Search Documents

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By John Mitchell, Mark K. Jorgensen

Newmont Mining’s Ahafo Mine is located in Ghana approximately 300 km (190 miles) northwest of the capital city of Accra in the Brong-Ahafo region. The nearest city is Sunyani, located 45 km (28 miles) to the north. The Ahafo Mine will process ore from seven major pits that extend along a 40-km (25-mile) strike. Four pits are in the south and three pits are in the north. The resource is currently stated at 373 t (12 million oz). But it still has the potential for growth both from new discoveries and the development of underground operations.

Jan 1, 2007

By D. Ouellet, G. Gagnon, B. Simser, V. Falmagne

The mining sequence at Noranda’s Bell- Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the redimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Jan 1, 2004

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By John K. Owens, Wayne L. Howie

Mobile roof support (MRS) machines are used as roof support during pillar recovery in retreat operations in lieu of wooden posts, cribs, or hydraulic props. A Mine Safety and Health Administration-permissible load rate monitoring system was developed for the MRS by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. The system uses a dedicated embedded processor to monitor changes in pressure inside the hydraulic cylinders of the MRS through multiplexed data acquisition channels and converts these pressure changes to load rates that sequentially activate three load-rate-indicator lights mounted on the machine. Each light represents a different loading rate to alert mine personnel to dangerous conditions during pillar extraction.

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002