Search Documents

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By Bradford F. Townsend, Gary Peach, Roger Rothenburger

From the experience of the authors on recent large infrastructure Design-Build projects this paper reviews major lessons for Contractors and Owners in the delivery of large Design-Build infrastructure projects and some major pitfalls and warnings to both Owners and Contractors. The paper is written from both the Design and Construction perspective. A case history is presented that details the approach employed to ensure a quality project consistent from the initial design phase through construction and outlines the strategy used to guide the Design-Build process to an acceptable completion. Suggestions are made for Contractors and Owners for handling the Design and the Construction elements of Design-Build contracts.

Jan 1, 2003

By B. Culkin

The production of fine particle products within the mineral processing industry is a very important market segment. Many of these products are processed in an aqueous state and must ultimately be dewatered. This entails processes which are very energy and capital intensive. The introduction of membrane based dewatering systems has offered great promise in the area of energy saving and operating costs. Unfortunately, membrane separators have not yet had the ability to handle high solids. New Logic introduces a system which can concentrate a low solids stream to a high solids sludge in a one pass, very energy efficient system.

Jan 1, 1993

By D. Olsen

The paper discusses the legislative and practical approach adopted to problems of management of environment in relation to coal mining in a very sensitive area of the south coast of New South Wales. The environmental problems are complicated in this area due to multiple and very often conflicting land usages. The environmental approach in relation to water quality maintenance, noise control and air quality is discussed and methods adopted meet stringent requirements. Requirements of New South Wales Regulations on Environmental Impact Statements (EIS) are described.

Jan 1, 1988

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By Paul D. Kovscek, Charles D. Taylor, Edward D. Thimons

When blowing ventilation is used on a mining section, a machine-mounted scrubber is often required to maintain face dust levels below 2 mg/m3. Operation of the scrubber also affects airflow patterns at the face and the dilution of liberated methane. Reductions in scrubber flow can result in increased methane concentrations. During mining, loading of the scrubber filter with dust is likely to reduce airflow. Detecting changes in scrubber flow is difficult, especially with extended cutting, because the machine must be operated from a remote location. Tests were conducted to demonstrate how scrubber airflow could be continuously monitored at a remote location. Three variables, static pressure at the fan inlet, differential pressure across the scrubber filter, and scrubber fan motor current, were continuously monitored while the scrubber filter was incrementally loaded to reduce air flow. The results show that monitoring each variable provided a way for estimating scrubber flow.

Jan 1, 1995

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999

By E. Topuz, C. Patrick

Longwall face-to-face equipment transfers or moves are the largest source of nonproductive time in a long wall-mining system. Detailed planning and resourceful thinking are paramount for economical, safe and timely longwall moves. New equipment and innovative techniques are frequently tested to reduce overall more time. Determining the cost-effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project-duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several ideas.

Jan 1, 1996

By P. T. Bissert, J. P. Ducarme, J. D. Noll, C. C. Jobes

"There have been about 42 fatalities in underground coal mines between 1984 and 2015 where the victim was struck, pinned, or run over by a mobile machine (MM) such as a shuttle car, scoop, or battery hauler. MSHA has issued a proposed rule requiring proximity detection systems (PDS) on MMs in an effort to prevent future fatalities. Currently approved PDSs use electromagnetic (EM) technology to detect the presence of a miner and impose machine controls to prevent contact. The disadvantages of an EM-based PDS on MMs include the need for a miner-wearable component (MWC), environmental interferences, EM interferences from other devices, and low localization range and accuracy. NIOSH researchers are investigating alternate technologies that could improve the capabilities of the current PDSs. Many technologies were reviewed, and NIOSH researchers identified RFID, LIDAR, RADAR, ultrasonic detection, and computer vision as candidates for PDS development. The performance characteristics of each technology and its applicability to an underground mining environment will be discussed, along with international developments and implementations, and the concept of sensor fusion. INTRODUCTION PDSs provide safety to mine workers by detecting their presence (and in some cases location) around a machine. These PDSs provide a warning zone, which triggers an alarm, and a stop zone, which halts the machine before it contacts the miner. The Mine Safety and Health Administration (MSHA) issued a final rule requiring that PDSs be installed on all continuous mining machines (CMMs) on the working section, with the exception of full-faced machines, according to a phase-in schedule for newly manufactured and existing equipment [1]. The PDSs that were designed for CMMs have since been adapted to other mobile machines. Mobile machines include scoops, which are used as general utility vehicles, as well as coal hauling machines, such as shuttle cars, ram cars, and continuous haulage systems. MSHA has examined all accident reports from 1984 to 2014, and determined that 42 fatalities could have been prevented on mobile machines had a PDS been installed [2]. As such, MSHA issued a proposed rule that would require mobile machines on working sections (with the exception of longwall sections) to be equipped with a PDS. This rule would follow a phase-in schedule for newly manufactured and existing equipment. Currently available PDSs are based on electromagnetic (EM) technology. NIOSH researchers developed a shell-based magnetic flux density distribution model [3] for determining the position of a miner near a machine. A typical system would consist of four generators positioned around the perimeter of the machine. Each generator is a coil of insulated wire wrapped around a ferrite core. The magnetic field strength is proportional to the current running through the coil. Miners working on the section have an MWC, which is a transceiver that measures the field strength emitted by the generators and transmits a data packet over an RF link which contains the field strength reading to the PDS controller mounted on the machine. The magnetic field generators are pulsed sequentially such that the MWC can identify which generator’s field strength it is reading. This type of system utilizes the principle of magnetic flux density: the closer the MWC is to the field generators, the higher the field strength reading. Thus a miner’s presence can be determined once he gets too close to the machine, because his MWC will measure a magnetic flux density beyond a certain threshold. These thresholds are utilized on a per-generator basis to “shape” the fields for both warning and stop zones around a machine, as illustrated in Figure 1."

Jan 1, 2017

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry's ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry's technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By J. C. Judd, D. D. Harbuck, M. D. Odekirk

The US Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent, such as SO2 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage countercurrent leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with SO2 or sulfuric acid.

Jan 1, 1992

By Pierre Mousset-Jones, Felipe Calizaya

The design of an auxiliary ventilation system for long underground openings (drifts, ramps and shafts), often requires the installation of multiple fans. The fans are installed in series and separated from each other by rigid ducts of fixed or variable length. However, problems relating to excessive leakage often occur, with each project representing a unique problem requiring an efficient solution. In this study, a method to determine the design parameters of an auxiliary ventilation system is presented. The method is based on the principle of partitioning a long ductwork into segments of finite length and solving the resulting networks separately. Specifically, the method is developed to solve two types of problems: constant fan spacing, and constant fan size. In the former, the fan spacing is fixed, and the problem is solved for fan sizes. In the latter, the problem is to solve for fan spacing. An example is used to illustrate the method.

Jan 1, 1993

By Stephen Day, Maria Falutsu, Gary Coulter

Open-pit mining began at Red Dog in 1989. Mining is expected to continue past 2030 but closure planning is an ongoing process. Geochemical studies of rock and tailings were begun in 1996 as part of development of closure plans to address leaching of metals and ARD. The deposit has many different primary and secondary sulfur minerals in amounts that preclude the use of conventional geochemical characterization methods. This paper will describe development of a specific chemical method to estimate the speciation of sulfur and classify wastes according to reactivity.

Jan 1, 2000

By O. C. Carter, B. J. Scheiner

The Bureau of Mines is investigating the effects of rainfall and gypsum/cooling pond water on the rate of metal and nonmetal ion mobility through phosphogypsum stacks located in central Florida. Since leachate contains metal and nonmetal ions that have the potential for migration into surface and groundwater, laboratory column leach tests were conducted. Synthetic rainwater was passed through the column and metal and nonmetal ion migration was monitored. Similar experiments were conducted using a number of synthetic solutions which simulated a number of different compositions of gypsum/cooling pond water. Results indicate that within the first five pore volumes most of the mobile metals and nonmetals were removed.

Jan 1, 1992