Search Documents

By C. K. Gupta

The paper reports on the experimental work and results obtained in processing a xenotime concentrate. The rare earth resource concentrate has been treated by three different methods namely, hydrothermal leaching, alkali roasting and alkali pugging or baking. The recovery in hydrothermal leaching with caustic soda at 150-160°C has been 89%. En comparison, processes involving alkali roastings with soda ash at 850°C and with caustic soda at 500°C, and alkali pugging or baking with caustic soda at 200°C have given recovery values close to 100%

Jan 1, 1992

By Y. Pokhvisnev, S. Vandariev, A. Yatshenko-Juk, V. Valavin, V. Romenets

The technology of the liquid-phase reduction process known as Romelt was developed in the Moscow Institute of Steel and Alloys in 1979. The pilot plant was constructed at the Novolipetsky Steel Works (Russia) in 1984. Investigations into processing zinc-containing blast oxygen furnace dust and slag from the Lead and Zinc Works at the pilot Romelt plant proved the perspective of using this technology for processing zinc and lead-containing materials. In this article, the description of Romelt technology, basic technological information of trials at the Romelt plant using zinc-containing materials, compositions of charging materials, metal, slag, gas and dust are presented. The influence of flue gas composition on the composition of zinccontaining dust is shown.

Jan 1, 2000

By Hong N. Vu, Jitka Jandova

"Gypsum and limestone methods were examined in this study to process zinnwaldite wastes originating from dressing Sn-W ores mined in the Czech Republic. These wastes containing 0.20-0.30% Li and 0.10-0.20% Rb were subjected to magnetic separation to obtain a zinnwaldite concentrate with 1.36% Li and 0.94% Rb. It was observed that processing of the zinnwaldite concentrate with gypsum resulted in almost 96% recovery of Li into aqueous liquors, whilst rubidium extraction was only 25%. At the same time, it is possible to extract almost 92% Li and Rb from the identical zinnwaldite concentrate if the concentrate is processed by limestone method. Lithium carbonate, a final product of both methods was recovered from the refined sulphate solution using K2CO3 as a precipitation agent and/or from unrefined hydroxide solution using gaseous CO2. In the continuation of this study, rubidium will be separated from carbonate solutions after Li2CO3 precipitation as RbAl(SO4)2, an intermediate for Rb2CO3 production. IntroductionLithium is used as an alloying constituent in lightweight alloys, as a heat transfer medium in nuclear reactors and as a component in primary and secondary batteries. With the development of a new generation of electric vehicles, the lithium demand will dramatically grow. Lithium chemicals find extensive application in many industrial branches such as metallurgical, glass, ceramic and pharmaceutical industries. Rubidium compounds are predominantly used in psychiatry and medicine, in magneto-optic modulators, solid-state lasers, phosphors and components of electrolytes for fuel cells. The four most important lithium minerals are amblygonite, spodumene, petalite, and lepidolite. Spodumene LiAlSi2O6 (6.0-7.5% Li2O) and petalite LiAlSi4O10 (3.5-4.5% Li2O) belong to aluminosilcate minerals. Lepidolite (Li.Al)3(Al.Si)4O10(F.OH)2 (3.30-7.74% Li2O), lithium mica, is the most important representative of the mica minerals, a subgroup of the aluminosilicates. It frequently contains 3–5% Rb2O and eventually caesium. Zinnwaldite, which has the general formula K(Li.Al.Fe)3(Al.Si)4O10(F.OH)2 (2-5% Li2O), is regarded as a variety of lepidolite with a high iron content. Commercial amblygonite is a complex phosphate (Li.Na)Al(F.OH)PO4 (up to 9.88% Li2O), however, its deposits have not been commercially exploited because of their small size. Natural brines with a high lithium chloride content are important in the industrial production of lithium [l]"

Jan 1, 2008

By G. Ramadorai

"This paper addresses processing options for recovering gold from carbonaceous sulfidic gold ores. These include, but not limited, to the following methods: (1) Hypochlorite pretreatment followed by cyanidization; (2) Chemical blanking agents pre-treatment followed by cyanidization; (3) Non-cyanide heap leaching techniques; (4) biological pre-treatment followed by cyanidization; (5) biological pre-treatment followed by non cyanide heap leaching. Issues of costs, economics, recoveries, testing methods, state of advancement etc., will be discussed in the paper.ABSTRACT ONLY"

Jan 1, 1997

By Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems are less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIXTM) and fixed film biological reactor, Denite°. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1994

By K. L. Money, R. R. Bleakney, R. H. Hanewald

The processing of EAF baghouse dusts, rolling mill scales, and belt grinding swarfs from the specialty steel industry will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions, filter cakes, spent nickel and chromium plating baths, super alloy wastes, and nickel-cadmium batteries. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery.

Jan 1, 2000

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996

By C. T. Philipp

Recycling of waste is much preferred over disposal. This paper discusses the Enviroscience, Inc. (ESI) process, now being commercialized by MetWool, Inc., to recycle hazardous wastes using an extractive metallurgical process which is followed by vitrification of non-reducible metal oxides. In this process, volatile and reducible metals are reclaimed as their respective oxides and elements.

Jan 1, 1995

By Ali Kucuk, Bekir Karasu, Keriman Karaveli Pekkan

"Zircon (zirconium silicate) is the main opacifier of glossy, opaque, white colored, frit-based wall tile glazes. However, zirconia containing frits employed in the preparation of these glazes increase the production cost and therefore, limit zircon usage as a raw material at industrial scale. With the present study, it was searched whether borax solid wastes could be evaluated as a component in the starting relevant frit recipes. The wastes were obtained from Eti Maden Kirka Boron Company of Turkiye. Frit production, glaze preparation, application, and fast single-firing of glazed wall tiles were conducted under laboratory working conditions in Anadolu University, Department of Materials Science and Engineering laboratories. Beside standard tests applied to the final glazed wall tiles, color and gloss analyses of the fired glazes were conducted with a spectrophoto-meter and a gloss-meter. Characterization of these newly produced glass-ceramic glazes was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques. IntroductionFrits are the indispensable constituents of most industrial glazes which mature at temperatures below 1150 °C [1]. In the traditional opaque glazes used in wall tile industry, opacity usually originates through hardening of glass matrix by adding high amounts of zirconia containing frits into the glaze batch [2]. Nowadays, researches point out that certain type of glass-ceramic layers can be alternatively employed as tile coatings lowering the use of zirconia containing expensive opaque frits. A rather high crystallization capacity of glass- ceramic glazes due to zirconia presence in glass network makes them suitable candidate as a glaze coating with a desirable micro-structure. One of the best methods to obtain an opaque glaze surface is to induce a crystal phase in the coating, whose refractive index differs significantly from that of the glassy matrix. The opacity of such coating is determined by the diffusion, refraction and reflection of light through the layer containing emerging crystals, and the degree of opacity mainly depends on the size and quantity of crystals. The development of glazes not consisting of expensive or toxic components is of special interest [3]."

Jan 1, 2008

By Yang Tian-zu

Sodium pyroantimonate which is widely used as the clarifier in the glass industry and as the synergist in anti-flaming industry respectively has a production history of about 30 years in China. At present there is the production capacity of about 20,000 tons per year in China and China is chief producer of sodium pyroantimonate. In this work the production processes adopted by the producers of China, the operation conditions and the product qualities of sodium pyroantimonate prepared by different preparation methods have been summarized, and on the basis of comparing the advantages and disadvantages for each process the most advanced method - the air-oxidation method was introduced in detail. The production processes of sodium pyroantimonate mainly include the method of oxidation by sodium nitrate, the oxidation method of hydrogen peroxide, the potash salt method, the chlorination method and the air-oxidation method etc. The method of oxidation by sodium nitrate in which the crude antimony oxide, sodium carbonate and sodium nitrate are separately used as the raw material, the flux agent and the oxidant, has the advantage of short and simple technological process, but low grade quality of sodium pyroantimonate and bringing about serious environmental pollution are the disadvantages and this method has been substituted by other methods. Sodium pyroantimonate can be directly prepared by the hydrogen peroxide oxidation method with the advantages of simple technological process, high grade quality of the product and little environmental pollution. High grade quality of sodium pyroantimonate can be also synthesized by the potash salt method, in which industrial antimony white, the hydrogen peroxide, potassium hydroxide and sodium hydroxide are applied as the starting material. The disadvantages of these two preparation methods are high production cost and high requirements on the raw materials. The chlorination method with the crude antimony oxide, hydrochloric acid and chlorine as the raw material has the advantages of low production cost and high grade quality of the product. However complex process, high requirement of anti-corrosion for the equipments and producing plenty of waste water limit its application. The air-oxidation method with stibnite/jamesonite concentrate, sodium sulfide, and sodium hydroxide as the raw material and atmosphere as the oxidant is a newly developed method and its advantages are low production cost and the complex raw material can be treated by this method and its disadvantage is that the quality of sodium pyroantimonate is lower than that prepared by the oxidation method of hydrogen peroxide and the potash salt method.

Jan 1, 2006

By W. G. Davenport

The offgas from flash furnaces inadvertently contains dust. The dust contains 25 to 30% Cu so it must be treated for Cu recovery. This is almost always done by recycling it back through the flash furnace*. This chapter shows how dust production/recycle is included in our matrix calculations. It then discusses the effects of dust production/recycle on flash furnace industrial oxygen and oil requirements. It concludes that re-smelting of dust requires considerable industrial oxygen and fuel, so that dust production should be minimized. Recycled dust also takes the place of new concentrate in the flash furnace feed system, decreasing Smelter productivity -another reason to minimize dust production. Compositions of industrial dusts are given in Appendix VII and Table 18.3. Industrial quantities are given in Tables 2.1, 3.1, 19.1,20.1' and Appendix VI.

Jan 1, 2001

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By A. Ohno

"A new near net shape casting process, OHNO Continuous Casting (OCC), has been recently developed. In this process, molten metal is fed into a heated mold maintained at a temperature above the solidification temperature of the metal being cast. Solidification begins from the central core of the casting rather than the wall of the mold. With the heated mold, the formation of crystals on the mold wall is prevented and solidification occurs out of contact with the mold surface. This produces near net shaped products with smooth, mirror-like surfaces and unidirectional grain structures free from cavities, porosity and segregation. Any crystals formed at the beginning of solidification decrease in number as solidification progresses and eventually a single crystal product is obtained. This process is applicable to any metal alloys, converting them into new materials with superior properties and quality.IntroductionAs a result of growing technical demands for more advanced and diversified materials, the OHNO Continuous Casting (OCC) technology has found many new applications in industry. Considerable interest in the process has been shown in Japan and other countries because of its distinct ability to:produce a single crystal, (1)produce a remarkably clean cast surface without a witness mark,provide extremely good ductility,and reduce casting defects and segregation.This paper provides an overview of the principle of the OCC process and describes the remarkable characteristics of the material produced by this method."

Jan 1, 1988

By F. Garcia-Carcedo

This research aimed to develop a clean technology for the production of ZnO from residues generated by the steel making industry. Scientific and technologic parameters were both investigated in order to define an industrial methodology allowing the integral recycling of EAF dusts. A reengineering of the Waelz process was perform,~d, aiming to produce a clean fraction of ZnO, fluorine free, as well as a slag enriched in metallic iron, which can be recycled in electric arc furnaces. The technical conditions used to produce the ultra pure fraction of ZnO are described. The magnetic separation of the EAF dust allowing the production of a phase high in iron and recyclable to the electric arc furnace is also discussed. Thermodynamic of the volatilization of all the elements contained in the EAF dust was performed in order to better control the thermal process in the rotary kiln. Tests were run using different reducing agents, weakly or highly reactive, aiming to determine their specific efficiency.

Jan 1, 2000

By Tugba Basargan Çagatay Morall, Gülhayat Nasun-Saygili

"The aim of this study is to prepare the apatitic material using colemanite mineral (2CaO.3B2O3.5H2O) which was obtained from Eastern Anatolia, Turkey. For this purpose, colemanite mineral was reacted with different phosphate sources, namely, dipotassiumhydrogen phosphate, ammoniumhydrogen phosphate and ortophosphoric acid at various temperatures and time periods. Experiments were run in batch system. The apatitic material was prepared by a wet method and followed by heat treatment at various temperatures. Structure of the samples was analyzed by XRD, FTIR, XRF and SEM. The particle size analysis was also made for the result product. The experiments showed that reaction temperature, contact time and heating temperature are important parameters to transform the colemanite into apatitic structure. Reaction of colemanite with dipotassiumhydrogen phosphate and ammoniumhydrogen phosphate results in amorphous, non-stoichiometric hydroxyapatite type structure, while acid based phosphate source gives brushite and monetite type product before and after heat treatment, respectively.IntroductionBoron which has properties intermediate between metals and non-metals is a member of semiconductor group of elements. Its atom is very small and has three valence electrons. Boron exists in Earth's crust (from 5 mg/kg in basalts to 100 mg/kg in shale) and in the oceans (4.5 mg/l) [1]. Turkey has 60% of world's boron reserves which is mostly in the form of colemanite (2Ca0.3B203.5H20). Colemanite is the most important calcium containing commercial borate mineral with 5 mol of crystal water [2].Calcium phosphate cements are very useful for bone repair applications because of its chemical structure. They are injectable, easy to shape and can be maintained locally. Because of those reasons calcium phosphate cements are very effective to fill bone defects with an irregular shape [3]. Hydroxyapatite (Ca10(PO)6(OHh) is the major component of the bone (70 wt%). However, hydroxyapatite stoichiometry, composition and crystallinity differ in human skeleton system [4, 5].The main objective of the present work was to study the transformation of colemanite to apatitic material using different phosphate solutions at several time spans and temperatures. The experiments were run in a batch system, change in pH and also weight loss were measured after the experiments. Several analysis methods were used to investigate the chemical and structural changes."

Jan 1, 2012

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Milorad Cirkovic, Mile Bugarin, Vlastimir Trujic

"Industrial scale testing was performed in the plant-site of Bor Company. Charging sample was from 4-5 tons for each particular test. All operations in industrial scale investigations were carried out in one furnace. For the aim of successful realization of experiments, and primarily for safety and prevention the risk of toxic contamination the working environment, a plant was designed and constructed for cooling and wet dedusting of gases formed during smelting process, zinc removal and flame refinement of molten metal. For the requirements of industrial investigations a complete plant for cooling and wet dedusting of gases has been constructed for brass scrap processing. In this plant, the original ultra-sonic water spraying devices have been installed. The efficiency of such simplified system for gas treatment has been 98,6%. Introduction Permanent development of techniques and technology causes formation the considerable quantities of secondary raw materials that are much more relevant as the raw material base for many metals. Due to a fact that large quantities of metal, are concentrated in the waste materials, large consideration is given to this topic, and numerous technologies for this waste recycling are developed in the world nowadays. High energz price and permanent increase of metal price on the world market have made that secondary raw material tretament, for the aim of various metals production, becomes more and more relevant in the world. In comparison of metal production using enrichment and metallurgical treatment of primary raw materials, the non-ferrous metals production from secondary raw materials has a range of advantages, as well as: - Low level of capital investments, - High technological recovery of qualitative secondary raw materils, - Considerably low consumption of energetic resources regarding to the treatment of primary raw materials (ore and concentrate), - Reduced consumption of unrecoverable mineral resources, - Reduced enviroment pollution [1,6]."

Jan 1, 2008

By E. Açma

In this study, the production of Cu, Co, and magnetic iron oxide from the ancient copper, slags, located in Küre-Turkey, is investigated. In the process under development, fayalitic slags containing 1% Cu, 0.43% Co are reduced in a D.C. arc furnace with coke or graphite additions. A metallic alloy, consisting of 3.8% Cu, 3.3% Co, 2.1% S, and the rest being Ice, is produced by granulation of the liquid metal. About 85% recoveries of Cu and C:o are achieved by hot sulfuric acid leaching of these granules followed by H2S precipitation. The, production of magnetic iron oxide is possible from the discarded leach solution, loaded v:ith FeS04, by using a method with geothite precipitation, dehydration, controlled reduction, and re-oxidation steps. The magnetic oxides produced have 20 m2Jg surface area, 1:8.3 aspect ratio, and the coercivity of 330-380 Oersted.

Jan 1, 1993

By Buket Tunçer, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are one of the most significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques

Jan 1, 2015