Search Documents

By Simon St J Tose

The objective of this paper and presentation is to review the different criteria and methodology used by AEL and other organisations to create a pre-split design which delivers a stable highwall for the life of that part of the mining operation. It will look at the need to adapt and change the way, size and direction of the production blasts as the mining phase approaches the highwall position for which a pre-split has been created. Key Words: Pre-split: Design; Highwall; Perimeter

Jan 1, 2006

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By G. Humphries, E. Wolmarans

The PPRust North project is an expansion of existing operations on the ?Platreef? orebody in the Limpopo Province of South Africa. Anglo Platinum has been mining and processing the Platreef since 1993 at the adjacent Sandsloot and Zwartfontein South open pits at a current rate of approximately 4.5 million tons per annum. This paper describes the origin of the proposed process flow sheet. A comprehensive test work programme has been conducted evaluating the best process flow sheet for the very hard and variable ore in the proposed mining area. The selection of the comminution circuit is discussed where conventional crushing and SABC options were analysed based on both extensive test work and analyses of current operational data at the existing concentrator. The application of the high pressure grinding roll technology has significant advantages?it replaces the 3rd and 4th stage crushing stages in a conventional circuit. This programme has been conducted over several years and has involved work done at site at pilot scale, internally at the company?s research facilities and externally at various sites. The on-site pilot work was completed over a 7-month period at the existing concentrator facility using a ThyssenKrupp-Polysius, ?Polycom?, 950 mm by 350 mm, high pressure grinding rolls (HPGR) machine. In excess of 185 000 tons of ore was processed through the unit during the trial period. This paper describes the test work programme and particularly the proposed application of high pressure grinding technology and its potential for further application in the platinum industry.

Jan 1, 2006

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By R. M. Lamya

The leaching behaviour of nickel?copper matte in an acidic?copper sulphate solution during the repulping stage at Impala Platinum Refineries has been studied. The base metal recovery process consists of a matte repulping stage prior to a series of pressure leach stages. Therefore, the repulping stage is basically an atmospheric leach stage in which the matte containing mostly Niand Cu is leached in copper-spent electrolyte from the tank house, resulting in dissolution of nickel and precipitation of almost all the copper. To understand the nature of the leaching process during this stage of the operation, the effects of temperature stirring rate and matte particle size on the rate and extent of base metal dissolution and copper rejection from the solution have been investigated. The leaching mechanism of the matte in the investigated system is alsoproposed.

Jan 1, 2006

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By S. Sakurai, N. Shimizu

The stability of slopes is a crucial problem not only in open pit mines, but also in civil engineering situations. The deformational behaviour of slopes is in general monitored during/after the excavation by carrying out field measurements where displacement measurements are commonly adopted. In monitoring the slope stability it should be emphasized that the measurement results must be properly interpreted so as to assess whether the slopes are stable or become unstable in the future. In order to interpret the data, back analysis is extremely useful. In this paper a slope stability monitoring system is described. It consists of displacement measurements by GPS, and a back analysis of measured data. The use of GPS has a great advantage, because of the fact that continuous displacement measurements with high accuracy for a large extent of concerned area can be easily achieved. On the other hand, the back analysis can reveal the mechanical characteristics of the ground, which make it possible to assess the stability of slopes quantitatively.

Jan 1, 2006

By Luis-Fernando Contreras, Juliano Maran, Richard LeSueur

A risk study was carried out at the Cerrejon coal mine in order to assess the impacts of pit slope failure in terms of safety of personnel and destruction of equipment with economic consequences. Results of the assessment enabled the definition of risk treatment requirements and the identification of key aspects to consider in a risk treatment plan. The approach included the following tasks: (1) Assessment of the total probability of failure (POF) representative of the stability conditions of typical footwall and highwall slopes. For this purpose, stability analyses were carried out to define the Design POF, which accounts for the variability of strength parameters and represents the normal conditions considered for slope design. Strength parameters for highwall slope analysis were derived from borehole data obtained with a geotechnical drilling campaign. The Total POF was estimated through the use of Source Response Diagrams (SRD) in order to incorporate other sources of uncertainty not accounted for, like changes in geometry, variability of rock conditions due to geological or operational factors, changes in groundwater conditions and occurrence of seismic events. (2) Assessment of the consequences of footwall and highwall slope failure on safety of personnel. The assessment was performed through the use of event tree analysis to establish the probability of fatality caused by slope failures, from the Total POF defined in the previous task. This analysis required the evaluation of personal exposure to slope failures. Also, the assessment included benchmarking of acceptability criteria in terms of probability of fatality and the evaluation of options of risk mitigation to comply with these criteria. (3) Assessment of the consequences of footwall and highwall slope failure in terms of economic losses associated with impact on equipment. The analysis included the evaluation of equipment exposure to slope failures, and it was performed through event tree analysis to establish the probability of an economic loss associated to total or partial lost of equipment, from the total POF value defined in the first task. The magnitude of the economic losses was estimated from the costs of damaged equipment, lost production and site restoration. Options of risk mitigation were also examined in terms of economic losses. The risk assessment process applied to the Cerrejón mine showed how the system can be applied to evaluate the consequences of failure in terms of personnel safety and economics and to identify the more adequate risk mitigation options. The system can be an extremely powerful tool in the mine design process and provides the opportunity to rationalize the geotechnical information requirements, once the risk criteria have been defined by management. The main purpose of this paper is to present the process; therefore, the emphasis has been put on the methodology followed rather than on the actual results obtained.

Jan 1, 2006

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By Brian Wyatt, Neil Webb, Marcel Roche, John Thirkettle

Recent developments in survey techniques and measuring equipment now allow for an accurate assessment of external coating condition and cathodic protection performance. These developments build on 20 years of experience of using Direct Current Voltage Gradient (DCVG) and Close Interval Potential Survey (CIPS) methods. The techniques use the latest advances in measurement systems coupled to a bespoke data processing system. The paper describes tests and trial surveys carried out on a hydrocarbon transmission pipeline in West Africa during 2005. The survey works described and conclusions drawn are from the data collected. Of particular interest are the apparent capacitance effects which are thought to occur under disbonded coating and the characteristics that these may show on the integrated CIPS and recorded DCVG profiles. This paper was originally presented at the Cefracor conference in Aix, France, in June 2006 The pipeline was originally installed on a phased basis between 1989 and 1994. The external coatings were three layer polyethylene factory coating and shrink sleeve field joint coating. An impressed current cathodic protection system was installed. The pipeline has subsequently been affected by disbondment of the coatings. It was a primary objective of the trials to attempt to identify such affected areas. In addition to a technically detailed account of the survey works undertaken and the results obtained the authors will consider the practical and commercial aspects of these surveys with input that provides a perspective from the specifier, pipeline surveyor, pipeline operations personnel and the pipeline owner. It is intended that the data presented will provide greater awareness of the benefits and limitations of the techniques used and their role for both stand-alone interpretation and the integration of the survey information with other inspection methods used for external corrosion assessment. The application of the described techniques is well developed and proven to locate and characterise through?coating defects and to provide a full audit of cathodic protection status. However, the possibility of the techniques being able to indicate disbonded coating is unproven and further tests and trials are planned which may allow a greater understanding of the electrical characteristics which are believed to be associated with disbonded coatings which may or may not be filled with an electrolyte. Further work is currently planned in West Africa, South Africa and Scotland in order to improve the understanding of this technique and to determine if the reported indications do actually represent a method of locating disbonded coatings. Keywords: External Coating, Cathodic Protection, DCVG, CIPS, corrosion assessment.

Jan 1, 2006