Search Documents

By E. J. Magri, A. Couble

Kriging estimates of geological resources are sometimes conditionally biased because the kriging plan contains too few samples. This may be done purposely in order to match the variance of the estimates to the true block dispersion variance. This work aims at evaluating the influence of conditional bias over the ultimate optimum pit design in relation to its shape, size and NPV (Net Present Value of profits). It has been restricted to two real case studies: a ‘carrot shaped’ gold porphyry in northern Greece and a manto-typeexotic copper deposit located in northern Chile. The methodology applied to each deposit consisted of generating a ‘real block model’ and four resource estimates by the use of conditional simulation and the application of four different kriging plans to the drillhole databases respectively. The estimation models vary in smoothness and conditional bias. Ultimate optimum pits were determined for the ‘real’ and the four different kriging models. Pit comparisons lead to the following conclusions: •In the worst case, conditional bias overestimated the project's NPV by 32% and 5% for the gold and copper deposits respectively. •The overestimation of high grades is more relevant than the underestimation of low grades. This resulted in a tonnage over-extraction of 148% and 1% for the gold and copper deposit respectively. This difference was attributable to the vastly different geometry of the deposits. •The smoothing effect of kriging, without or very little conditional bias, produced open pits that were different to the ‘true’ (ideal) ones and furthermore, underestimated the project's NPV by 10% and 6% for the gold and the copper deposits respectively. •Other factors that influence the optimum open pit design and to some extent control the effect of conditional bias are: the cut-off grade, the orebody geometry and distribution of grades within it and the amount of over-burden. Keywords: conditional bias, ultimate pit design

Jan 1, 2003

By J. Kuijpers

Failure and fracturing are often regarded as synonymous. While this is obviously true in an environment dominated by tensile stresses, it is still not clear how failure and macro fracturing are related in a compressive stress environment. Excavations at great depths are typically subjected to compressive stresses only. The fracturing observed around such excavations is therefore commonly assumed to be induced by such compressive stresses. The physics of such a phenomenon have unfortunately never been explained properly, so that the formation of these so-called extension fractures still remains a mystery. As the presence of fractures is an important factor affecting the stability of underground excavations, it is of practical relevance to understand their formation. In this paper, a possible explanation is proposed. It is argued that fracturing in a compressive stress environment is a secondary effect. Primary failure, in the form of micro fracturing and associated damage is assumed to precede the major fracture processes. The fractures are thus generated in response to material failure and may not directly be the cause of failure. The implications for material response and behaviour are discussed. Keywords: micro fracturing, macro fracturing, extension fractures, failure, compressive stresses, damage, excavations.

Jan 1, 2000

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

By J. L. Havenga

South Africa produces about 400 Kt zircon (ZrSiO4) per annum. This represents about 30 percent of the global demand. However, very little is beneficiated locally and more than 95 percent is exported with little or no value addition. Zircon is a very inert material and needs to undergo high-temperature alkaline melting processes to produce valuable zirconium products. The conversion of zircon to plasma-dissociated zircon (PDZ) produces a chemically reactive species (ZrO2.SiO2) which consist of finely divided submicron monoclinic ZrO2 crystals dispersed in a SiO2 matrix. In this paper, an in-flight, non-transferred arc pilot plasma plant with a capacity of 100 kg/h and which consists of three 150 kW DC plasma torches, is described. The optimization of the plant, which includes the use of different zircon concentrates, the influence of particle size, feed rates, plasma gas, and energy utilization, is discussed.

Jan 1, 2012

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By K. R. Vost

This paper reviews the theoretical methods used in South Africa for the prediction of heat pick-up and air-temperature gradients along main haulages. These methods include those of Starfield, Ramsden, McPherson, and Goch and Patterson. The differences in predictions based on typical airway conditions are explained as being due to differences in the mathematical models on which the predictions are based. The largest discrepancies were found for dry airways and for airways with bulk air coolers. The errors in predictions of the effect of machines and coolers that have been running for only a few months are calculated, and the limitations of various simplified methods are discussed.

Jan 1, 1982

By T. C. Marshall

A comparison between hydraulic and pneumatic rockdrills by T. C. Marshall, Pr.Eng. (Member) The greatly increased output of rockdrills has placed new demands on booms, carriers, and drill steels and bits. Limited scope for further improvement in pneumatic rockdrills has led to the development of hydraulic rockdrills, which compare favourably with their pneumatic counterparts: they are more efficient, more flexible in coping with variations in the working conditions, more economical in the consumption of drill steel, and less productive of noise and mist. Their disadvantages include a greater need for a reliable power supply, a greater vulnerability to dirt, greater complexity (requiring more skilful maintenance), and the liberation of heat into the working environment. They should be regarded as a complement to, and not as a substitute for, pneumatic rockdrills.

Jan 2, 1974

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By J. Maiti

This study examined the group differences in accident susceptibility among underground coal mine workers accounting for their personal and workplace characteristics. A logistic regression model was used for this purpose. Data were collected from five underground coal mines for a period of four years. The case study results revealed that different age and experience groups of workers bear no significant differences in their accident susceptibility; however, the workplace location and occupation groups show significant differences in their risk of injuries. It is inferred based on the logistic model results that among the three occupation groups, the face workers are more susceptible towards accidents/injuries compared to the haulage and other workers. Key Words: Mine Safety, Accident Susceptibility, Group Differences, and Logistic Regression.

Jan 1, 2001

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By N. A. Barcza

Pointing out that South Africa needs to utilize its wealth-creating activities, together with local and international investment, to further develop its industries, the address asserts that the mining and minerals industries, especially in the manufacture of beneficiated products, offer the greatest potential for South Africa to achieve its goal. As many mineral-beneficiation processes are based on pyrometallurgical routes, the address goes on to describe some historical - pyrometallurgical operations and to indicate probable developments in the future. These include growth in the fields of both precious and base metals. After discussing environmental and recycling matters, together with manpower requirements, the address concludes that the major growth in the mining and minerals industries will occur in the manufacture of steel, stainless steel, ferro-alloys (particularly ferrochromium), aluminium, and titania slag.

Jan 1, 1996

By M. C. van Blerck

This paper examines the South African fiscal system as it applies to the mining industry and, where components are found wanting, discusses possible alternatives. It is concluded that the South African system has long provided a stable environment for mining investment and growth. However, the introduction, of steep surcharges during the past decade or so (since abolished) and ring fencing (since relaxed but not abolished) has started undermining this stability.

Jan 1, 1994

By J. M. Font, R. G. Reddy

Jan 1, 2004

By E. Cetin

Orebodies that contain more than one economically important mineral are generally evaluated by parametric cut-off grades. This approach often leads to mis-valuation of mineral deposits because cut-off grades are not based on the grades of each individual mineral and, because of the parametric formulation, are only indirectly related to the individual grade distributions. The only realistic approach is a formulation that accounts separately for each component mineral. The grid search method can be used as a means of multi-mineral cut-off grade optimization in this context. This paper describes the use of the grid search method in cut-off grade optimization for multi-mineral deposits. The authors introduce the general concepts of the method and formulate its application to cut-off grade optimization; they describe a software implementation of the method that can accommodate cut-off grade optimization for mineral deposits that contain up to three economic minerals. Keywords cut-off grade, optimization, grid search, multi-mineral deposits.

Aug 1, 2013

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012