Search Documents

By V. C. Robinson

INTRODUCTION Most presidential addresses are in the nature of a review of some specific topic and this will be no different. In thinking about the subjects which might be suitable for this address I decided that as next month will see my retirement from the gold mining industry I might review the four decades since I started in the industry in 1929. These four decades have been more than usually in',~resting and exciting. They have covered a period when the price of gold increased from the old figure of 84/- an ounce to the price of $35 an ounce today, taking in on the way at least two periods of premium sales from which the producer benefitted. The industry in these four decades has survived the most totally destructive war in history and has seen fundamental changes in the political, economic and governmental life of South Africa. There have been great technological changes and improvements, some of which I shall refer to later, and in addition there have been profound changes in the relations between employer and employee in the industry which have affected not only the economy of the industry but the traditional thinking of both management and labour. I believe that the address presented to this Institute on the occasion of its 75th Anniversary by Mr Goode covered more than adequately the history of the Institute and the part it has played in the mining industry of South Africa. It would be merely repetitive, therefore, to discuss the affairs of the Institute of Mining and Metallurgy. Having said this, however, it is also necessary to point out that the history of the Institute is, and always will be, an important record of the history of mining in South Africa. There are many facets, however, on which we ought to look back and to re-examine. One of the most rewarding, but at the same time one of the dullest, places to look for historical facts is in the annual reports of the Chamber of Mines. I suppose that some of the dullest of these have been the reports for which paragraphs have been prepared by me personally. The notes which follow do not claim to be anything like a full record of this exciting period. RISE AND FALL OF THE GOLD MINING INDUSTRY In talking about the mining industry of South Africa it is inevitable that one talks, particularly in the historical sense, about the gold mining industry - an industry of fundamental importance which has made South Africa what it is and which has been dying since the early part of this century. In Table I is shown the progress of the gold mining industry measured by its output of ounces of fine gold from the beginning of operations until the end of 1969, and if you are interested in the productivity of the men who work this industry the table, composed entirely from figures set out in the Chamber's annual reports, also shows the production of gold expressed as fine ounces per European and fine ounces per Bantu worker over a long period. If you are still minded to think of this industry as dying then the last column in the table shows how uranium has played such a vital part in the prosperity of the country.

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By J. Kuijpers

Failure and fracturing are often regarded as synonymous. While this is obviously true in an environment dominated by tensile stresses, it is still not clear how failure and macro fracturing are related in a compressive stress environment. Excavations at great depths are typically subjected to compressive stresses only. The fracturing observed around such excavations is therefore commonly assumed to be induced by such compressive stresses. The physics of such a phenomenon have unfortunately never been explained properly, so that the formation of these so-called extension fractures still remains a mystery. As the presence of fractures is an important factor affecting the stability of underground excavations, it is of practical relevance to understand their formation. In this paper, a possible explanation is proposed. It is argued that fracturing in a compressive stress environment is a secondary effect. Primary failure, in the form of micro fracturing and associated damage is assumed to precede the major fracture processes. The fractures are thus generated in response to material failure and may not directly be the cause of failure. The implications for material response and behaviour are discussed. Keywords: micro fracturing, macro fracturing, extension fractures, failure, compressive stresses, damage, excavations.

Jan 1, 2000

By M. Mokgohloa, T. R. Stacey

Boring of tunnels and shafts in hard rock under high stress conditions is becoming more common as mines and tunnels are developed at greater depths. Under the high stress conditions, fracturing of the often-brittle rock occurs in the walls, backs, and ahead of advancing faces of excavations. Fracturing can have a significant impact on boring activities: sidewall spalling, which affects machine gripper capacity, and fractures can also develop in the rock ahead of the face, leading to blocky rock conditions, which may have a significant effect on machine excavation. Fracturing may develop dynamically, leading to rock bursts manifesting in the form of strain bursts, which can be hazardous and destructive. In brittle rock, fracturing is commonly extensional in nature. The focus of this paper is on fracturing in the face of the excavation. Examples of such fracturing behaviour are described briefly in the paper. Numerical analyses were carried out to predict the initiation of extension fractures and their orientations ahead of excavation surfaces, and the resulting formation of rock slabs/plates, and the stability of these plates. The results should be beneficial for the evaluation of the conditions prior to, and during boring operations.

Nov 27, 2024

By FJ Fourie

Lack of success in attempts to develop viable large-scale continuous mining techniques (previously reported by MP o?Hare in 2004) led the team at Kopanang to explore alternative solutions to their ongoing need for improved profitability. By calling into question the basic assumptions around the stoping of narrow tabular deposits of gold, fragmentation and more particularly, the range of sizes of blasted rocks eventually became the focus of serious study. This background is briefly covered before the sequence of the investigations is described. So far, some of the ?rules of thumb? derived over the years have been confirmed, albeit for totally different reasons than those from which they arose; some persistent theories on gold loss have been debunked, and some new ones have been developed. Blast optimisation (the means by which desired fragmentation is achieved) has been based on tailoring energy to rock characteristics in an innovative packaging design for explosive charges. Other beneficial consequences arising from the work include increased production volume and gold output, a decrease in milling consumables, and the Mine Call Factor is being maintained at a level previously thought to be unachievable. This is very much a ?work in progress?, and it is empirical in its approach. The authors are the first to recognise that they have yet to determine in absolute measures why some of the innovations have had the effect that has been observed. Also that there other factors which may contribute to the result, but which have not yet been examined. Nevertheless, publication of the work completed so far is felt to be justified; firstly on the basis of the achievements themselves, and secondly for the benefit of others in the industry for whom similar problems exist. Statistical reports of the effects on the business are included at the end of the report. Detailed laboratory test results have been separated into an appendix, leaving salient graph and tabulated data in the main text. For ease of reading, units of measurement for particle sizes below 1mm are described in microns, but millimetres have been retained for those at that size or greater.

Jan 1, 2007

By M. Grozdanovic, D. Marjanovic, M. Ilic

We present a framework for solving the problem of functional compatibility between process control equipment in control centres at underground mines and operator capabilities. The equipment incorporates displays of current ventilation, gas, and fire hazard data, status of alarm and early warning systems, a voice communication subsystem, and facilities for recording and printing ofdata and reports. The layout of the existing control panel is compared with a recommended design. The basic principles of ergonomic design and arrangement of the controls and indicators, as well as ease of use, type of operations carried out with these controls, and operators’ viewing angles are discussed. The objective is to improve the usability of control panels, display boards, and graphic screens so as to enhance the functioning of control centres and optimize control of technological processes in coal mines.

Jun 10, 2024

By W. Kotze

The gold mining industry has mainly relied upon the use of highly polluting chemicals, such as mercury and cyanide to recover gold from its ores. The Coal Gold Agglomeration (CGA) process was developed some years ago and has the advantage in that gold is recovered by a procedure which has little or no negative impact on the environment. A gold ore containing liberated gold particles is contacted with coal-oil agglomerates, where by the gold is recovered into the coal/oil phase. Laboratory scale batch tests were performed on an artificial mixture gold slurry and gold recoveries of up to 85% were found under optimized conditions. By recycling the coal/oil phase, it was found that the gold loading onto the agglomerates was increased. Tests performed on an industrial ore yielded slightly lower gold recoveries, and X-ray Diffraction (XRD) analysis on the coal/oil phase showed that minerals other than gold was recovered into this phase. A comparative study was conducted whereby the CGA process was compared to mercury amalgamation. Gold recoveries obtained through amalgamation were 15% lower than by the agglomeration process, which indicates that this process can be considered favourably as an alternative to amalgamation.

Jan 1, 2000

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By J. Cilliers, R. Seitz, D. Drinkwater

Mineral processing produces a saleable product from high-cost ore. The Mineral Processing Engineer must constantly improve the separation to create the most value from the ore and reduce the associated costs. Graduate Metallurgists (or Chemical Engineers) have had the university theoretical training required, but often are illprepared to perform their plant roles. The in-work Metcelerate programme was designed specifically to develop the practical skills that Mineral Process Engineers require, by combining three key elements: 1. Knowledge transfer through self-paced, on-line training; 2. Practical skills acquisition through assessed, practical plant exercises; 3. Skills development through online tutorials. A final process improvement project adds significant value to the operation that far exceeds the training cost. Experience from Metcelerate clients has indicated improved staff retention, greater confidence, and pro-active process intervention.

Jan 1, 2023

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By D. Seke

Metal inventories are usually reported in financial statements of mining companies. However, the value of these inventories can be reliable only if the metals in stock are measured within acceptable tolerances. Reliable metal balancing requires accurate mass measurement, sampling, and chemical analysis. Many mining companies are usually unable to validate the accuracy of metals in inventories at the end of their financial year. This is mainly due to poor mass measurement, sampling, and chemical analysis practices. This has an adverse impact on metallurgical accounting and metal valuation. In addition, it puts a lot of stress on external auditors, who have the duty to recommend the approval of the financial statements to the board of directors. Although a full value chain of metal reconciliation includes the accuracy of Mineral Reserve definition and grade control at the mine, this paper discusses the implementation of best practices for mass measurement, sampling, and chemical analysis at processing plants. This is an important aspect of sampling and reconciliation that is required in order to improve the reporting of inventories in the financial statements of public mining companies. Keywords metallurgical accounting, corporate governance, sampling, analysis.

Jan 1, 2014

The influence of Harold Hotelling?s work in the field of mineral economics is both unusual and outstanding. In the 66 years since its development, theory surrounding the economics of exhaustible resources has only been significantly researched since the early 1970s. At that time a wave of research into the economics of exhaustible resources arose from the threat of global resource scarcity and continued into the late 1990s. Current East Asian and global demand for natural resources as well as mineral and metal commodities, has stimulated interest in the optimal and sustainable exploitation of exhaustible resources to the point that the subject is worthy of review. Hotelling?s theory and the assumptions that he made in establishing a model for the optimal exploitation of mineral resources at the industry level and at the level of the individual mine owner, are examined. He showed that the rate of increase inexhaustible resource prices should be equivalent to the market rate of interest and that in a market with rising prices the rate of extraction should be constant. In markets where demand is stable optimal exploitation requires that the rate of extraction should decline over time, while in a monopoly market he showed that the rate of extraction is retarded. In addition, the effects of cumulative production on costs and prices, the uncertainty associated with estimates of the resource stock, the impact of exploration and issues of intergenerational equity are examined. An analysis of the optimal price path, extraction costs and mineral rents at an industry level is presented as a model. An analysis of the rates of production and optimal benefits at the individual mine level including total, average and marginal costs on the optimal rate of production, is considered. Optimal extraction rates for a mine with a clearly defined concave positive cost equation vary according to the position on the marginal cost curve. The influence of discount rates and the size of the ore reserves on the rates of mineral extraction are also examined and could define the frontier of usefulness for the ?economics of exhaustible resources?.

Jan 1, 2007

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By D. Mesa, J. Karvonenb, A. López, P. R. Brito-Parada, R. Grau, D. Davoise

The froth zone in flotation cells plays an important role in determining metallurgical performance. This is even more critical as cell sizes increase, since larger bursting surface areas can easily result in poor froth transport and even stagnant froth zones, which are detrimental to recovery. Generating additional overflowing lip length by adding internal launders and reducing surface area (while also directing the froth to the overflow) by adding crowders are well established design strategies to enhance froth mobility. However, comparative experimental studies of froth zone design modifications at industrial scale are scarce and often lack detailed froth characterisation. In this work, we present the results of two experimental campaigns that were carried out at Atalaya’s Riotinto concentrator in order to determine the effect of a new froth zone design on the flotation performance of a TankCell® e300 cell that operates as the first cell of the rougher bank. These campaigns provided a unique opportunity to assess froth phase phenomena and metallurgical performance before and after changes in design. The original cell design had an internal peripherical launder and a froth cone, while the new concentrate launder technology adds a centre launder and an adjustable froth crowder to the existing launder design. The new concentrate launder arrangement reduces significantly the froth area as well as the froth transport requirements, aiming to improve froth recovery and, consequently, enhance flotation performance, allowing copper recoveries in the TankCell® e300 cell to increase dramatically. In addition, radial profiles of froth height and froth velocity at the surface were determined, which provide valuable insight into the effect of design changes on froth stability and mobility. Keywords: Flotation performance, enhanced recovery, launder, crowder, froth stability

Jan 1, 2020

By L. Ozdemir, B. Asbury, T. G. Rozgonyi

A new type of bit, that has been developed and is being evaluated, shows great potential in expanding the range of rock strength that can be cut by continuous miners and roadheaders. This new style of bit is called the frustum. The tools tested in this program were developed, manufactured and patented by Briese Industrial Technologies, Inc. The frustum derives its name from the unique geometric shape of the cutter, or cutting insert. The frustum shape cutting tool has previously been proven as an effective cutting tool for machining metals, metal matrix composites and polymers. The frustum rock bit has a very dense carbide frustum shape tip mounted on the end of a steel body similar to the conical bits typically used on continuous miners and roadheaders. In between the carbide frustum cutting tip and the steel body there can be a bearing that allows the frustum to rotate around the bit axis. When the bit is forced into the rock at a skewed angle, the frustum tip rotates as it travels. This rotation greatly reduces the cutting forces acting on the bit when compared to the current state of the art conical drag bits. This cutting force reduction, derived from the frustum’s cutting action, allows for much harder and more abrasive rock to be cut without quickly wearing out the bit. Full scale laboratory cutting tests have been performed with the frustum bit in direct comparison to the current state of the art conical bits. Field trials of the frustum bit are currently being planned. Test procedures, results and findings are presented.

Sep 1, 2001