Search Documents

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By Arcy R., D&apos George

The Bureau of Mines has developed, on a laboratory scale, a superior Eluex-type circuit for eluting and recovering uranium from ion exchange resins. The improved circuit differs from conventional Eluex practice in that a stage of uranium solvent extraction is coupled with each stage of resin elution rather than the elution and solvent extraction operations being conducted separately. The new system reduces the number of stages, retention time, and resin inventory in the elution circuit to one-fourth or one-fifth that in existing circuits. The system is applicable to both resin-in-pulp and moving-bed-type ion exchange uranium recovery circuits.

Jan 1, 1969

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By J. E. Wilson

A bench-scale expansion tester using 71 grams of coal was developed to determine the practicability of an apparatus of this size to investigate the effect of variables such as oxidation, blending, bulk density, inerts, size consist, petrographic differences, and rate of heating on the expanding properties of coal. The value of this tester is shown by the correlation that exists between its results and those of the larger scale sole-heated oven expansion apparatus used in commercial plants. From tests on 32 coals the standard error of estimate for predicting sole-oven results from bench-scale results is ± 5.3 percentage points. A standard deviation of the difference between pairs of tests in the latter apparatus of ± 2.1 percentage points was determined for 31 samples. In the sole-heated oven test the expansion of a coal at constant pressure is directly proportional to the dry coal bulk density. Tests in the bench-scale tester show a similar relationship between expansion and bulk density. When the blending ratios of high-and low-volatile coals are varied, similar changes in expansion are observed in both the sole-heated oven and the bench-scale tester. Therefore, the effect of other variables on expansion should be similar in the latter apparatus.

Jan 1, 1960

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.' Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world's least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country's first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

To provide accurate navigation and control of continuous mining systems.

Jan 1, 1996

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

By H. M. Thorne

The oil-shale deposits of the Puertollano basin in the Spanish province of Ciudad Real appear to have been give little consideration in discussions of oil-shale resources throughout the world. A small, integrated oil-shale operation has been conducted at Puertollano since about 1922 by a French company, Sociedad Mimora y Metalurgica de Penarroya, hereinafter referred to as "Penarroya", but only within recent years have the potentialities of the Spanish oil-shale deposits been recognized. Empresa Nacional "Calvo Sotelo" do Combustibles y Lubricantes, hereinafter designated as "Calvo Sotelo," which was created in 1942 by the National Industrial Institute of Spain to produce liquid fuels from oil shales, has made marked progress in the design and construction of a complete oil-shale plant at Puertollano. Penarroya is mainly a coal-mining company, and the oil-shale operations were on a small scale of approximately 220 tons a day in October 1947. It is an integrated operation comprising oil-shale mining and retorting and shale-oil refining. Motor gasoline, Diesel fuel oil, light burner fuel oil, lubricants, paraffin wax, cresols, and ammonium sulfate are manufactured.

Jan 1, 1950

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

The Aluminum Co. of America raised its 99.5 percent unalloyed aluminum ingot selling price in March by 34 to 514 per pound. Other producers, including Kaiser Aluminum and Chemical Corp. , Anaconda Aluminum Co. , and Reynolds Metals Co., followed Alcoa's lead, raising their quotes to 51$. In late March, domestic merchants quoted ingot at levels ranging between 49.56 and 50.50 per pound. BISMUTH: Several domes tic dealers lowered their bismuth prices in recent weeks by 50t-606 to within a range of $5.60-$5.75 per pound; producers continue to hold published prices at $7.50.

Jan 1, 1977

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Marshall County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, were estimated at 3,158 million short tons as of January I, 1954. Of this total, 3,071 million short tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By D. E. Andrus

This paper, which describes the milling practice at the Montana mine concentrator of the Eagle-Picher Lead Co., is one of a series being prepared by the United Slates Bureau of Mines. LOCATION The Montana mine is situated on the eastern edge of the Oro Blanco mountains at an elevation of 4,300 feet. It is in the Oro Blanco mining district, Santa Cruz County, in the southern part of Arizona, about 4 miles north of the Mexican border, 30 miles northwest of Nogales and 80 miles southwest of Tucson. Amado, a station on the Southern Pacific Railroad, midway between Tucson and Nogales, and about 40 miles northeast of the mine, is the shipping point and is reached over an excellent highway.

Jan 1, 1931