Search Documents

By R. H. Kudlich

In order to assist the various Federal and State agencies using large quantities of coal to select coal best suited technically and economically to their use, the United States Bureau of Mines has placed at their disposal a fuel inspection service. As part of this service, inspections are made at the mines which propose to furnish coal to these agencies on contracts. Such inspections cover both the mine itself to ascertain its capacity to fur- nish the desired tonnage and quality of the coal, the preparation of the coal in the tipple, and the obtaining of samples for analysis to determine the quality of coal as shipped. To insure that the sample sent to the laboratory for analysis is representative of the average quality of the coal, increments are taken at intervals until a gross sample of about 1,000 pounds of coal has been collected from each of the sizes of coal shipped by the mine, while coal has been coming from all parts of the mine. In reducing this gross sample to the small sample which is sent to the laboratory for analysis it is necessary to crush and quarter the coal by a certain standardized method until only 5 or 6 pounds of coal small enough to pass through a 3/16-inch square-mesh screen remains. The ordinary method which the bureau has followed was to crush the coal by hand with a tamper, such as is used for tamping concrete, on some hare smooth surface and to reduce the volume by quartering and riffling. During the past few years the demands from various Federal and State agencies for this service have been increasing rapidly in respect to bituminous coals. In addition to this, which might be called the normal increase, numerous requests have been received for similar service in respect to anthracite. It was obvious that if this increased demand was to be met it would be necessary either to increase the force allotted to this work or to provide the present force with some means by which their work could be made more effective. A care- ful survey of the situation showed that the greatest amount of time was consumed in trans- porting the men and their equipment from mine to mine in the same district, and in reducing the gross sample to the small finely crushed sample which is to be sent to the laboratory. Both of these phases of the work could be greatly accelerated by providing a motor truck of suitable speed and capacity, carrying a power-operated crusher, and the proper auxiliary equipment to store the gross sample as collected and to reduce it in volume efficiently after it has been crushed. Such a truck has been provided and placed in service. In the eight months it has been in operation the desired results have been fully attained. About twice as many samples as usual have been taken during that time by the same 2-pan crew assigned to this work. Many of the mines in the eastern part of the United States are in hilly or mountainous regions and can be reached only over rough, practically unimproved roads. Hence the speci- fications for the truck were drawn to cover high-quality, long-life trucks, in order that

Nov 1, 1931

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By L. C. IlsLey, M. W. Means

The United States Bureau of Mines under provisions of Schedule 20 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equip- ment and assemble them, thereby making up a permissible unit. Before the assembler purchases electrical accessories for use in such contempla.ed units he may require certain information from the accessory manufacturer as to whether these par- ticular accessories are suitable for assembly in his proposed permissible outfit. In order to aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies. The section of Schedule 20 which permits this special work reads as follows:

Jan 1, 1932

By H. H. Storch

Methane is the chief constituent of natural gas, and large quantities of it are also obtained in coke-oven gas and in the off-gases from cracking higher hydrocarbons. Perhaps the most important potential chemical use of methane is in the production of higher hydro- carbons, both aliphatic and aromatic. The results of a relatively large number of researches have been published in the technical and patent literature on the thermal decomposition of methane, the objective being an industrial process for the production of "antiknock" motor fuel. No industrially feasible process has, however, been developed. An inspection of the literature on this subject indicates that the chief difficulty in the way of accomplishing this object lies in controlling the decomposition so that undesirable products are eliminated. A considerable number of quantitative experiments have been reported, the results of which provide only a vague and confusing picture of the various steps in the thermal decomposition of methane. The reaction mechanism has not been subjected to rigorous fundamental study, and the necessity for such a study is obvious if further progress is to be made. The thermal decomposition is only one of the reactions of methane which are of potential industrial importance and which require further fundamental investigation. The oxidation, hydrolysis, and halogenation of methane are other reactions which must be studied further. In view of the importance of methane as a raw material for various industrially desirable products, it is appropriate that a survey be made of the important facts concerning the physical and chemical properties of methane which will serve as an aid in subsequent experi- mental work. No attempt will be made to present a complete chronological review, but rather a condensed critical description of the important literature will be presented.

Jan 1, 1932

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

By W. J. Fullerton

This paper is one of a series prepared for the United States Bureau of Mines discussing the methods used in crushing and grinding materials for cement manufacture, and deal particularly with the methods used at the Howes Cave plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Albert W. Cox

This paper, one of a series prepared for the United States Bureau of Mines discussing the methods used in mining, crushing, and grinding materials for cement manufacture, deals particularly with the methods used at the Security plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of, total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shall ensue.

Jan 1, 1932

By M. R. McKenzie

This paper describing the milling methods at the Walkermine concentrator, Plumas County, Calif., is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to James O. Elton, manager of the International Smelting Co., and to Henry A. Geisendorfer, manager of the Walker Mining Co., for permission to present this paper; to H. A. Geisendorfer and J. D. Roberts, shift boss, for historical facts, and to D. D. MacLellan, geologist, for geological information.

Jan 1, 1932

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By D. Harrington

We Americans fondly believe that ours is the greatest , most progressive and most civilized country in the world , but the cold statistical facts reveal that we apparently have little appreciation for the lives of those whose efforts of various kinds give us whatever greatness we have . The latest available statistics indicate that the annual death rate per 100,000 persons , from accidents is nearly 80 , or far higher than that of any other country in the world ; it is more than double the rate in Denmark , Belgium, Netherlands , France , Sweden , Italy , Ireland , Germany , Norway, and Austria; it is practically double the rate in England and Wales and in Japan , and is from 25 to 60 per cent higher than the corresponding rate in Scotland , New Zealand , Australia, Switzerland , and Canada . And added to this is the fact that of the main industries of the United States mining has by far the worst accident record , viewed from either the frequency or the severity basis . The National Safety Council's latest figures for 27 of the country's main industries give mining the highest or worst accident frequency rate, 74.43 in 1929 ; meat packing comes next with 55.94 , and construction third with 50.41 . In accident severity in 1929 mining also was the worst offender , with a rate of 9.99 ; quarrying is second with 6.11 , and construction third with 4.62 . Metal mining's frequency rate in 1929 was 52.16 , as against 69.25 for bituminous coal mining ,99.68 for anthracite mining, and 74.43 for the entire mining industry ; accident severity for metal mining in 1929 was 5.99 , as against 11.69 for bituminous coal mining , 10.87 for anthracite mining , and 9.99 for the mining industry as a whole . Although this figure indicated that metal mining is on a much safer plane than either bituminous or anthracite coal mining, the frequency rate of 52.16 for metal mining was higher in 1929 than the frequency rate of all but one of the other 26 industries about which data are available ; the metal mining severity rate of 5.99 , while much better

Mar 1, 1932

By Paul Hatmaker

Pumice and pumicite are siliceous volcanic substances quite similar in chemical composition , but somewhat different in physical properties , manner of formation , and mode of occurrence . Production in the United States has increased from 23,271 tons valued at $ 94,943 in 1910 , to 56,843 tons valued at $336,099 in 1930. Both pumice and pumicite are included in these figures as it has been impractical to collect statistical data on the separate commodities .

Mar 1, 1932

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By Paul M. Tyler

"In preparing this paper the writer has perforce depended mainly upon published information, including the catalogs and pamphlets issued by importers and dealers such as the Diamond Drill Carbon Co. and J. K. Smit & Zonen. Special acknowledgment is made to various articles published by S. H. Ball. The writer of this paper, however, is alone responsible for statements herein contained and since he has often found it necessary to rationalize apparently conflicting opinions of recognized authorities on this little-known subject, he will welcome constructive criticism from the trade.Two types of diamond are extensively used for industrial purposes. One type, known as bort or bortz (boort, boart, bowr, etc.), consists of diamonds of the gem variety but unfit for cutting into gems. They may be colorless, yellow, brown, or gray. The other type, carbonado, known in the trade as ""carbon"" or ""black diamond,"" differs greatly from the white diamond, being opaque and apparently amorphous or noncrystalline. Actually, instead of forming a large single crystal as in a gem stone, carbon diamond comprises a mass of microscopic crystals that interlock to form a tough, homogeneous material with no planes of cleavage. It is found in various colors -- black, dark green, brown, and gray -- but usually it has .a dark lustrous black surface, with a resinoid or submetallic appearance, often resembling fine-grained steel. Upon exposure to the air the broken surface gradually darkens to an ash-gray color. Ballas is a special type of carbonado in which the crystals are definitely-oriented around a central nucleus. They are harder and tougher than ordinary carbonado but are much scarcer. The Cape ballas is reputed to be not quite so tough as Brazilian ballas but tougher than carbon or bort.The diamond crystals are isometric and take a variety of forms. The cleavage is octahedral and well marked. A crack is easily -started parallel to an octahedral face, and bort or gem diamonds are notoriously brittle, especially when subjected to sudden shock. Even carbonado, while it has a high resistance to slowly applied pressures, may be chipped or broken by a sharp blow.Exposed to radioactive rays, the diamond becomes phosphorescent; this property is often utilized to distinguish it from quartz, topaz, or glass. The unusually high refractive index likewise aids in its identification in the case of a more or less transparent stone. At the temperature of the electric arc, diamond is converted into graphite, another form of Carbon but one of the softest mineral substances. At a much lower temperature, as low as 1,5620 F., the diamond may be burned like ordinary carbon in an atmosphere of oxygen, and according to some authorities there is danger of burning a diamond if overheated even in air."

Mar 1, 1932

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932

By John B. Umhau

In 1930 , 65,448 long tons of virgin or primary tin were consumed by 1,292 establishments in the United States , representing about 91 per cent of the total consumption as computed from imports , exports , and stocks at the beginning and the end of the year . The reported consumption was equivalent to 38 per cent of the world's tin production in 1930 , estimated at 171,000 tons , and was 12 per cent less than the 74,369 tons consumed by 1,307 establishments in 1928 . Decreased consumption of new tin in 1930 ás compared to 1928 was a reflection of the general industrial depression . All of the tin- consuming industries showed substantial decreases except tin plate and terneplate , white metal , and tinning , which showed small tonnage increases aggregating only 1,200 tons . The largest tonnage decrease was in the use of new tin in babbitt which declined 33 per cent in 1930 as compared to 1928. This was largely attributable to the decreased production of automobiles and trucks , which was 24 per cent lower in 1930 than in 1928. Percentage decreases in other important tin- consuming industries were as follows : Solder 18 per cent , bronze 19 per cent , tin foil 40 per cent , chemicals 23 per cent , tin oxide 44 per cent , and type metal 46 per cent . The distribution of the amount consumed by various uses during 1927 , 1928 , and 1930 is shown in table 1 . Consumption studies indicate the fact that variation in tin consumption from year to year parallels the fluctuations in demand for the already wellestablished tin products . For example , the manufacture of motor cars and trucks3 required only 11,000 tons of tin in 1930 compared to 19,000 tons in 1928 ; the canning industry continues to require the greater portion of the tin plate and much of the solder . Recently developed industries , while affecting total consumption of bearing metals , solders , etc. , to some extent , have made little change in the relative importance of these commodities as consumers of tin .

Jan 1, 1932

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932