Search Documents

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By L. X. Yu

As is known, the oxidized antimony and antimonate are hard to treat. A new combined mineral processing flowsheet which is controlled in grinding and classification ?bulk floatation?gravity separation is adopted to dispose of gravity-separated tailings (antimony content: 1.48%; oxidization rate: 68.92%) in Muli Antimony Mine, the grade of floatation antimony concentrates is 32.64%; the grade of gravity-separated antimony concentrates is 26.99%; the combined grade of floatation and gravity-separated antimony concentrates is 30.85%, and the total recovery of antimony is 70.64%. Adopting the new mineral processing technique have solved the problem of over grinding of antimony ore by controlling grinding and classification, recovering effectively the sulfide antimony and the easy floatable oxidized antimony of fine size by bulk floatation, recovering effectively the oxidized antimony which is hard to float by classified gravity separation. This is a great breakthrough in the mineral processing technique of the recovery of the oxidized antimony. At present, favorable economic benefit has been obtained from the application of this processing technique in Muli Antimony Mine.

Jan 1, 2014

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By Yuqing Feng, Ping Fang, Dezhou Wei, Zichuan Guan, Shuling Gao, Baoyu Cui

"Air core, as an inevitable phenomenon of rotational flow field inside hydrocyclone, has a major impact on hydrocyclone’s separation characteristics. The air core formation process, its structural features and its influencing factors were investigated systematically in this paper. Numerical study on the air core of a f50 mm hydrocyclone was carried out using a commercial computational fluid dynamics (CFD) modelling software package ANSYS/Fluent with the selection of Reynolds Stress Model (RSM) for the turbulence model and Volume of Fluid (VOF) for capturing the air-liquid interface. Physical experiments were conducted under the same geometry and operation conditions and the particle image velocimetry (PIV) technology was used to measure the liquid flow. The CFD results are compared with the experimental measurement with good agreement demonstrated. The air core was formed generally at around 0.7 s, air outsides of the air core was eliminated completely after 1.7 s. The centreline axial velocities and the water blocking hydrocyclone simulations showed that air of the air core entered the hydrocyclone from the underflow area and exhausted from the overflow area, but there was also some air flowing into the air core from the overflow area. The largest swing of the air core occurred on the top of the underflow pipe, and a protuberance similar to the shape of Adam’s apple appeared when the air entered the vortex finder. CFD simulation results also showed that the air core diameter was decided by axial position and parameters of hydrocyclone. The structural parameters have more effects on the air core diameter than the operational parameters."

Jan 1, 2014

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014