Search Documents

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013

By Yolaine le Beau

Plan de la présentation Le contexte mauritanien La situation de l?environnement en 1999 L?évolution de 1999 à 2010 Bilan La situation de l?environnement en 2011 Le contexte mauritanien Pays du Maghreb couvert à 75% par le désert du Sahara Un des plus pauvres au monde Index de développement humain : 136esur 169 pays en 2010 46,7% de la population ne peut subvenir à ses besoins quotidiens

May 1, 2011

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By Gordon T. McKenna

"Syncrude Canada Ltd. is developing new concepts in lease-closure landscape design for its Oil Sands Leases 17 and 22 in northeastern Alberta. Closure planning is becoming an integral part of the planning cycles and of the lease operation. By incorporating closure planning into the day-to-day operation, the company will achieve acceptable lease closure in an economical manner. Ultimately, Syncrude will achieve lower operating costs through innovation in mine planning and a reduction in residual liabilities.New concepts being evaluated for lease-closure landscape design include: designing for closure, use of landforms and natural analogs, self-armouring bouldery ground, robustness in design, landform grading, terrain analysis of reclaimed land, geotechnical hazard assessments, choices in closure design timeframes, passive maintenance, determining post-closure monitoring goals, engineering tailings, engineering other substrates, use of test plots and field demonstrations, geomorphologic monitoring of reclaimed lands, defining closure goals, and visiting other mines. These concepts are being formalized under the new discipline of Landscape Engineering."

Jan 1, 1996

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By A. W. White

Introduction To discuss all the technical details of incorporation laws, security laws, underwriting procedures, codes, and ethics-as laid down by varous associations -would be impossible in the time which has been allotted to me. My remarks, therefore, will be made in a very general way and will naturally be coloured with experiences which my firm and I have had. There is a common expression that "money makes the mare go". I hardly have to mention here that the best prospect in the country is of very little value unless its prospects can be developed-and this requires large capital expenditures. The art and problems surrounding the raising of this money is a long and interesting story. Since by its very nature mining is risky, the appraising of its risks in the many phases of its development programme is continuous. Very few men-if any-and very few corporations -if any -can afford to take all the risk of mining. Because of taxation policies-and the very scheme of present-day living -the truth of this statement can be seen throughout the whole industry by a close examination of the records. Since this is so, it is essential that the mechanics of distributing risk on a sound, and equitable basis be known to those engaged in the business and to the investor or spectator who proposes to risk his funds in the industry. Perhaps the greatest stimulant to modern business activities has been the creation of corporate bodies. It is evident, from the number of charters being granted by various jurisdictions, that this method of doing business is becoming more and more important. A limited company -or corporation-can be defined as a fictitious person existing solely in contemplation of the law.

Jan 1, 1951

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

Ion Exchange is finding a greater role in copper processing, and hydrometallurgy in general, both as a technique for removing impurities and as a means of adding value through the recovery of secondary metals. Both the gold and uranium industries use resin adsorption as a primary production technique. While hydrometallurgical processes predominantly rely on solvent extraction as the mainstay of copper recovery there are a number of projects, in particular polymetallic deposits, which are considering the use of resin recovery as an alternative or supplemental production technique. A number of applications have been developed and proven at commercial scale for the removal/control of impurities (iron, antimony and bismuth) from copper electrolytes. These are well documented ion exchange applications. Increasing metal values and scarcity of certain metals are focusing companies to look at secondary metals recovery rather than losing these often highly valuable metals to tails residues. Bleed streams are being seen as valuable opportunities to recover contained metals; iron, copper, nickel, cobalt, bismuth, antimony and rhenium are all metals being targeted for removal or recovery from process solutions, electrolytes and bleed streams. An overview of currently applied techniques as well as some developmental technologies for impurity removal and secondary metals recovery is presented to provide insight into the advantages and flexibility of ion exchange applications in metals processing.

Jan 1, 2007

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By Mario A. Morin

The last few years have seen considerable consolidation of the mining software industry and a trend towards greater planning and production control system integration, particularly for surface mines. The mining industry is starting to realize the benefits of system integration and will continue to drive the evolutions of these systems. Several trends can now be observed. The trends include application and system integration, data portability, ?intelligent? systems for support of decision-making activities, mine process-control and automation. While many planning systems are moving in this direction, there is room for considerable improvements. This paper will discuss these trends, examine the current state-of-the-art in mine design software, and identify areas where improvements should be made and why.

May 1, 2004

By J. E. Gill

Introduction During the past summer, detailed geological mapping was extended to cover the entire group of 31 claims owned by Waite-Ackerman-Montgomery Mines, Ltd., and considerable new information was revealed by development and exploratory work underground. These new facts provide a more complete view of the lithology and structure of the area than has heretofore been available. They also necessitate revision of certain interpretations presented last year by Peale (l), and have served to straighten out some of the problems suggested by Porritt (2). The purpose of this paper is to outline in a broad way the relations as now understood and to discuss in detail certain points which should be of interest to members of the Institute. Maps and records by the mine staff have been freely used in arriving at the interpretation presented in the following pages. The writers are especially indebted to Mr. R. V. Porritt, the mine manager, with whom many of the problems touched upon were discussed on the ground and whose intimate knowledge of the geology of the underground workings aided greatly in testing various hypotheses. The writers have profited greatly, also, from close association with Dr. W. F. James during the course of the work. Permission to publish the included data has very kindly been given .by the management.

Jan 1, 1932

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By Bradley Stoughton

The magnetic oxide of iron, F eO4 , contains a theoretically larger amount of iron ( 72.4 per cent.) than any other commercial ore. It is probable that it has originated in many cases by the prolonged exposure of the hydrated oxide, ZF e20 a + 3H20 to heat and pressure which converts it first into hematite, F e20 3, and then into magnetite. It would thus appear as if nature had already done part of the work of removing all the oxygen and that magnetite should be relatively easy to reduce. That it is, in fact, less reducible than either limonite or hematite, is due chiefly to its dense and compact physical structure, which makes it less pervious to the furnace gases, and also to its characteristic action in resisting crushing to a uniform size, with consequent irregularity in reducing conditions within the furnace. The net result is that the magnetic oxide requires more fuel and more time for its reduction in the blast-furnace than any other iron ore of similar iron content and physical condition. There is another very important reason why the smelting of magnetite is more costly than that of hematite, and its treatment viewed with a great deal of adverse prejudice by blast furnace operators, namely, that magnetite decreases the proportion of heat developed by the fuel in the stack of the furnace, and increases the already excessive heat requirements of the heart.

Jan 1, 1924