Search Documents

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By G. V. Smith, C. O. Tarr, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By Taylor Lyman, E. P. Klier

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

Jan 1, 1944

Jan 1, 1944

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division's Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By H. F. Yancey, M. R. Geer, Franklin T. Davis

Coke with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning, An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. Previous Work Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,' and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.'

Jan 1, 1944