Search Documents

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By BRETTMANN TRACY

Jan 1, 2000

By Robert J. Shanley

The computer program, HYBMODE, has been developed to meet the need for a fast and economical method for clustering data points on the sphere. The algorithm used in this development is an extension of D. Wishart's one-level mode analysis. The program can be used to cluster either vectorial or axial data; it is currently being used by the Bureau of Mines to cluster fracture orientations.

Jan 1, 1974

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By Silvio Hernández Aquije

El presente texto señala el descubrimento del yacimiento vanadífero de Minasragra a través del reporte de Yeatman-Berry en 1916 y el de Kett-Sproul en 1931. Así también señala los tipos de mineralización como la mineralización primaria y por impregnación.

Jul 1, 1955

By Michael A. Piepenburg

The East Side Access (ESA) Project will extend Long Island Rail Road (LIRR) into midtown Manhattan via 11 km of tunnels, a new terminal station and associated support facilities. In addition to the hard-rock tunneling currently underway in Manhattan, soft-ground tunnels in Queens will traverse beneath Amtrak?s Sunnyside Yard and Harold Interlocking, the busiest rail interlocking in North America. This paper details ESA?s coordinated approach to interfacing with both Amtrak and LIRR with regard to the planned tunnels, shafts and related construction beneath or adjacent to the operating railroads. This interface includes integration of railroad staff, extensive presentations, reviews and agreements with the railroads regarding settlement mitigation, real-time automated geo-instrumentation monitoring, ground improvement, and geotechnical/environmental controls.

By Joan Weinberg

The economy continued to expand during the third quarter, as real GNP rose at a seasonally adjusted annual rate of 3.8%, up from 2.5% in the second quarter (table 1). Continued job gains (see below), higher incomes, and an increase in installment debt, resulted in a nearly 20% increase in consumer spending on durable goods. Consumer expenditure on nondurables fell slightly, while spending on services continued at a moderate pace. Nonresidential fixed investment climbed nearly 24%, as producers purchased more durable equipment. Residential fixed investment was adversely affected by rising interest rates, which slowed new home construction from January to August, 1987 to a rate 11.2% below a comparable period in 1986. Net exports of goods and services deteriorated slightly, after three consecutive quarters of improvement. The volume of net exports has risen 15% for the year, contributing to economic and employment growth, but large price increases on imports have slowed the improvement in the nominal trade balance. Although U.S. goods have declined in price relative to foreign goods because of the devaluation of the dollar, faster growth in exports is hampered by austerity programs in developing countries, and emphasis in Germany and Japan on curtailing inflation and fiscal deficits.

Jan 1, 1987

By B. H. Good

This paper describes the research that has been conducted -in an effort to understand the nature and causes of sulphide fires -in the Sullivan Mine. Results of the investigation have led to several theories of the origin: of the fires, the nature of the chemistry and a method for assessing: the fire potential. Recommendations and the implications for the mining operation are also discussed.

Jan 1, 1977

By George J. Young

DR . JOHN A . CHURCH, in his treatise on the Comstock Locle 1 gave a full and clear account of the conditions of the mine during the period of greatest activity. The difficulties in the way of deep mining at that time were excessive water and high temperature. The drainage of the mines taxed the financial resources of the mining companies, and the high temperatures restricted the capacity of the miners for underground labor. In spite of these difficulties exploratory work was continued until the financial burden of removing the water became too great. The companies then restricted the work to the upper levels. The years 1883 to 1886 marked the period of cessation of deep mining. For 12 years thereafter mining was confined to the levels above the Sutro tunnel; and, while the question of drainage was more or less agitated, nothing of importance was done until the formation of the Comstock Pumping Association in 1898. Since that time successive levels have been drained until, at present, on the north-end mines, a depth of 700 ft. below the Sutro-tunnel level has been reached. Mining is now carried on in the Ophir mine from the 1,700- to the 2,200-ft. levels, and a winze is being sunk to make connection with the 2,300-ft. level (the 2,450 ft. of the C. & C. shaft). In 1903-the Ward Shaft Association was formed to undertake the draining of the Central and Gold Hill group of mines, and at the present time a depth of 2,500 ft. has been reached in the Ward shaft. The situation at the Ward looks promis¬ing, and the 3,000-ft. level may be reached in the near future. It is proposed to establish a large pumping-station on this level, and then begin the opening of known ore-bodies and the prospecting for new ones. The main factors which have contributed to the successful solution of the drainage problem are the Sutro tunnel, the use of the hydraulic elevator as a sinking-pump, the concentration of pumping-units, and cheap electrical power. The question of high temperature and its control still remains as a minor but important problem. The temperatures encountered in the new workings are as great as those in the earlier periods. The Comstock was considered the hottest group of mines in the world, and I am not aware of similar conditions in any other mining-district. A water-temperature as high as 160° F. has been reported from the Ward shaft, and temperatures below the Sutro tunnel are very high in many instances.

Nov 1, 1909

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By H. F. Moore

DURING the last six years, there have been many extensive investigations of the fatigue of metals. The major work of 'these investigations has been the determination of constants for fatigue strength of wrought ferrous metals; but during the past year or two there have become available considerable test data on the fatigue strength of certain nonrferrous metals, including copper, brass, bronze, nickel, copper-nickel alloys, aluminum and aluminum alloys, magnesium and magnesium alloys. It is not proposed to give here extensive quantitative tables of test results; for such tables, reference is made to the published data of various laboratories. The following general conclusions, however, seem to be fairly well established: 1. The phenomenon known as "fatigue" of metal really a progressive fracture of metals. A minute (probably submicroscopic) crack is formed in the metal, the internat stress, is intensified at the ends' of the crack, and under successive applications of load the crack spreads like a minute hacksaw cut until there is not enough sound metal left in the cross-section of the piece to stand the load. applied, and then failure occurs suddenly. 2. For wrought ferrous metals, there is .a limiting intensity of stress (as computed by the ordinary formulas of mechanics of materials) below which, a metal is able to withstand an indefinitely large number of repetitions of stress without failure. This limiting stress is known as the "endurance limit or the fatigue limit.? For reversed flexure, the endurance limit for. wrought ferrous metals is usually not far from 50 per cent. of the ultimate tensile strength.

Jan 1, 1925

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976

By Paul C. Hyndman

The U.S. Bureau of Mines inventoried Federal mineral lands in Idaho and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal restrictions and agencies' management practices. The Bureau also identified known mineral deposit areas (KMDAs) and areas conducive to oil, gas, and geothermal resources. This information is shown on maps (developed in part by geographic information system technology) that spatially compare the availability for mineral entry of Federal land with these KMDAs to demonstrate the extent and severity of restrictions on mineral entry. Idaho contains 53.1 million acres, 35.7 million (67%) of which is Federal mineral land. About 7 million acres of this land is within KMDAs that host medium-to high-value locatable mineral deposits; 36% of this land is available, 27% is slightly to moderately restricted, and 37% is severely restricted or unavailable. For the leasable minerals, about 1.8 million acres are within KMDAs that host medium-to high-value phosphate deposits, about 5.4 million acres are favorable for oil and gas resources, and 3.9 million acres for geothermal resources. The percentages of land availability are 30%, 45%, and 25% for the phosphate acreage, 38%, 34%, and 28% for the oil and gas acreage, and 43%, 30%, and 27% for the geothermal acreage.

Jan 1, 2012

By Joey Hoang, Robert Johansson, Tapani Keronen, Mikael Jåfs, Jani Jansson, Mikko Korpi

At the Copper 2016 conference in Kobe, Japan, Outotec introduced a vision for the year 2020, wherein smelting would make use of four digital cornerstones: intelligent instruments, advanced process control, improved information management and transparency of and access to data. Since then, this vision coined the phrase “Fully Automated Smelter” with the mission promising a concept where no manual actions from human operators would be needed during normal smelter operations. Replacing repetitive physical work, collection and analysis of everyday production data has a great potential for further automation and will provide productive ways to improve efficiency and safety of smelters in the future. Therefore, a lot of emphasis has been put into developing solutions to automate these tasks and to move people out of harm’s way. A lot of new equipment, systems and optimization tools are under development. In addition, a lot of effort is going into developing dynamic process models and advanced control systems to interface with the plant automation systems. The goal is to integrate all these concepts to meet Outotec’s Fully Automated Smelter vision. This paper will cover these latest achievements toward this vision and introduce the near-future of digital smelting. INTRODUCTION As is well known already, the humankind is currently experiencing a change, extent of which is broadly studied by the governmental, educational and industrial institutions and parties. The wellbeing and quality of life have traditionally been improved alongside the developments in industrial production, which is now about to enter its fourth revolution. Therefore, the current change is often described as fourth industrial revolution, or industry 4.0 (or industrie 4.0, as named by Acatech, 2013) and can be considered anything from small incremental development to a ground-breaking global reset that will affect everyone’s lives. Many seem to agree, that the scale of change will indeed be big, even significantly bigger than the three industrial revolutions before it (Pellini, Weyrauch, Malho & Carden, 2019; Geissbauer, Vedso & Schrauf, 2016; Jansson, Bjorklund, Lahtinen, Heinonen, Jafs & Fagerlund, 2016).

Jan 1, 2019

By B. A. Filas, H. N. Lammers

Responsible environmental, social, and governance (ESG) practices are not new to mining. It is the ESG acronym that has become the “flavor-of-the-day” with the stock markets, accounting firms, and investment strategists. This increased interest from the financial sector has heightened executive awareness and accountability to where corporate leadership and directors are proactively prioritizing ESG issues from the top down within their companies. This paper aims to convey what the authors believe one needs to know to be able to conduct and prepare effective ESG audits and reports. The emphasis is on how ESG fits within the mining sector, some of the ways that many mining companies have been practicing ESG responsibility for decades, the importance of effective communications with stakeholders, and the roles that regulatory and international lending institutions play in enhancing ESG practice on a global scale as a precursor to the discussion on ESG auditing and reporting. Without this background, the ESG audit may become a purely academic exercise.

Feb 1, 2023

By César Bernal M

El presente trabajo busca establecer el mejor plan de explotación de la mina Cobriza a través del nuevo proyecto de expansión. El plan de explotación señala que los ciclos de explotación, el número de tajeos requeridos por el método de corte y relleno, la selección del equipo de mina, así como los servicios auxiliares para suministrar el tonelaje necesario de mineral a la nueva planta de Coris.

Nov 8, 1982

By J. H. Rhee, H. B. Ku, J. S. Lee, H. J. Park, B. S. Jang

A large wedge failure had occurred in the study area which was under construction. Therefore, in order to analyze the potential instability for this rock slope, the authors conducted numerical analysis with DEM and then the behaviour of rock mass was analysed after appropriate reinforce-ments were applied. Ein großer Keildefekt geschah in dem Untersuchungsgebiet, das im Bau befindlich ist. Deshalb, um die potentielle Unbeständigkeit für diesen Felsenabhang zu analysieren, führen die Urheber zahlenmäßige Analyse mit DEM. Und dann wird die Bewegung der Felsenmasse ana-lysiert, nachdem angemessene Verstärkungstruppen angewandt werden. Un grand échec de coin sèst passé dans le région étudié qui était en construction. Par conséquent afin d’analyser linstabilité potentielle de cette pente de roches, les auteurs ont mené une analyse numérique avec DEM. Ensuite le comportement de la masse de roches pourrait être analysée après les renforts appropriés étaient appliqués.

Jan 1, 2003

By Shigeru Tsutsumi

The rapid development of transportation facilities in Japan focused the attention of this country on the possibility of converting the existing coal resources (of which there was an abundance) into liquid fuels, for which there was a constantly increasing demand. Previous work had indicated that this could be accomplished by utilizing one of two processes - the Bergius process, in which high temperatures and high pressures were employed to effect direct liquefaction of the coal, and the Fischer-Tropsch process, in which an indirect liquefaction of coal was accomplished by the production of liquid hydro-carbons from hydrogen-carbon monoxide mixtures. This report describes some investigations into the latter process, which was first developed by Fischer and his colleagues in the Coal Laboratory in Muhlheim, Germany, in 1923. By 1932, these investigators had achieved a 60-percent theoretical yield (152 ml. of liquid hydrocarbons per cubic meter of 2H2:ICO synthesis gas) by using a precipitated Co-Th02 catalyst.3/ At the same time (1932), Dr. Kita of Kyoto Imperial University and Messrs. Fujimura and Tsuneoka obtained 145 ml. of gasoline (C5+) per cubic meter of synthetic gas by using a Co-Cu-Th-U catalyst. 4/ This report is a description of the experimental results subsequently obtained at the Fuel Research Institute, Kawaguchi City, Saitama, up to 1935.

Jan 1, 1951

By H. S. COOLEY

TO talk about a "factor of economy" in connection with the wire ropes used in mining practice may be coining a new phrase. If such be the case it needs no other apology than that economy in wire rope usage is so bound up with the factor of safety as to justify a similarity in naming that makes one suggest the other. At the latest Wire Rope Research Conference, held under the auspices of the A. S. M. E., Re- search Committee and Engineering Foundation, data were introduced covering mine ropes working under

Jan 1, 1930