Search Documents

By Sheng-hai Yang

The ultrafine, monodispersed, spherical cobalt powder has been fabricated by reducing cobalt hydroxide with glycol. It were investigated that the effect of NaOH concentration on the reaction rate and the effects of the concentration of cobalt hydroxide and surfactant on the morphology and particle size. The particles were characterized by the X-ray diffraction(XRD), scanning electron microscope(SEM), laser diffraction particle size analyzer and BET specific surface analyzer respectively. The XRD shows that the cobalt powders exist mostly in face centered cubic (fcc) structure, a little in simple hexagonal. The cobalt powders prepared at Co(OH)2150g/L, NaOH 40 g/L and surfactant 30g/L, its average particle size, specific surface area and cobalt content, were 0.88µm, 2.705m2/g. and more than 99.5% respectively.

Jan 1, 2006

By J. K. Brimacombe

Since the Peirce-Smith converter was introduced to the non-ferrous industry in the early part of this century, there has been a paucity of research on process-engineering aspects of the reactor such as gas injection. This paper reviews studies conducted at UBC over the last decade on gas discharge dynamics, high-pressure injection, bath slopping, oxygen/bath reaction kinetics and out-of-stack heat transfer within the converter. The ultimate objectives of this work have been to extend refractory life and to increase converter productivity.

Jan 1, 1985

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000

By Akira Yazawa

In the field of pyrometallurgy, the equilibrium evaluation has recently become easy by use of thermodynamic software, but it is strongly desired to estimate the amounts of non-equilibrium minor components to simulate practical processes. However, simple physico-chemical technique can not be applied to evaluate practical non-equilibrium components for many reasons. As an engineering solution for postulated equilibrium system, the activity coefficient is modified and introduced as the simulation parameter referred to as the "adjustment coefficient." This modified thermodynamic calculations were adopted to various sulfide roasting processes where many solid phases are participating and the system is not necessarily in equilibrium. Successful simulation was realized by assigning suitable adjustment coefficients for minor components which form a pseudo solid solution in the calcine. Some examples from sulfation roasting and dearsenizing roasting were discussed. In the smelting system, the loss of copper in slag is caused by equilibrium and non- equilibrium reasons, that is, chemical dissolution and entrainment of copper in slag. The total copper content of slag was simulated by use of the adjustment coefficient for entrained copper.

Jan 1, 1998

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By Li Ma, Shaoguo Chen, Gele Qing, Qihang Liu, Keng Wu

Olivine contains higher MgO element, which can be added into blast furnace burden to improve slag stability and fluidity. Effect of calcined olivine and untreated olivine on low silicon pellet production process and quality was studied in this paper. The results shows, calcined olivine has no effect on bursting temperature of green pellet, however the bursting temperature of green pellet will decrease with increase of untreated olivine ratio. Untreated olivine has slight effect on green pellet strength than calcined olivine while the ratio is higher than 2%. The compressive strength of low silicon pellet will increase first and decrease afterwards with increases of calcined olivine ratio under firing temperature of 1250°C, whereas, the changing sequence is reverse fired under 1280°C. The result of untreated olivine pellet compressive strength is same as calcined olivine pellet. However, the compressive strength and metallurgical property of calcined olivine pellet is slightly higher than that of untreated olivine pellet under same condition.

Jan 1, 2015

By Jean-Christophe Gebelin, Mark Jolly, Samantha Jones

"The de-waxing process in investment casting is truly a black art which is carried out in a black hole - the autoclave. The process involves exposing wax, coated by a porous ceramic shell, to steam at a pressure of 10 bar and a temperature of about 180°C. The processes which then occur are truly multi-media and multi-physics. Steam condenses in the porous ceramic, wax melts and flows, the shells expand and sometimes crack. Why the shells crack is one of the most difficult questions asked in the industry.Modelling and validating the de-waxing process is not simple. The IRC at the University of Birmingham is attempting to model this process using Physica+ a code developed in the UK. This paper will present the latest results in this attempt to model one of the casting industries most intractable problems.IntroductionThe de-waxing process using an autoclave involves the following physical phenomena:· Flow of the steam in the autoclave;· Heat transfer from the steam to the wax, possibly through the shell;· Melting and flow of the wax.At the same time, other phenomena may occur, such as the flow of the steam through the shell, the condensation of the steam on the shell surface and on the wax pattern surface, the flow of wax the through the shell, etc ...This shows how complex the de-waxing process is from a physical point of view. The main defect that appears during this process is the cracking of the shell. Previous modelling work carried out by Snow [1] has shown that it is possible to predict the stress in the shell, making numerous assumptions. In this paper, the modelling to predict the state of stress in the shell that is currently in development at the University of Birmingham is presented together with the presentation ofthe physical phenomena to model and the assumptions used. The parameters that are needed in such models will also be discussed, and some experimental work undertaken at the moment presented."

Jan 1, 2001

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By Yuanbo Zhang, Bin Xu, Guanghui Li, Xiao Kang, Chen Liu, Tao Jiang

Iron-bearing dusts, containing valuable constituents such as Fe, CaO, MgO, C, etc., are generally utilized as raw material in iron ore sintering. However, the dusts characterized by low granulating and refractory performances always lead to negative effects on sintering indexes. As we know, the innovative process named composite agglomeration process (CAP) has a series of advantages compared to traditional sintering process (TSP). In CAP, part or all of the iron-bearing dusts is made into green pellets with 5-15mm in diameter, while the rest of iron-bearing dusts and all of the other fine ores is granulated after mixing with fuels, fluxes and return fines. Compared with TSP, CAP could increase the ratio of iron-bearing dusts from 5% to over 20%. Meanwhile, the yield, ISO tumbler index and productivity reached 75.82%, 65.13% and 1.531t·m-2·h -1, respectively.

Jan 1, 2015

By Zvi Rivlin

Classical nucleation theory states that in first order phase transformations, such as liquid to solid transition, nucleation of the product phase starts with the formation of small, unstable clusters (embryos). When the thermodynamic barrier to nucleation is overcome, the embryos grow and attain a critical size, beyond which they are stable, i.e. they become nuclei. If nucle- ation does not occur, the parent, liquid phase remains in metastable equilibrium. At temperature lowers, undercooling increase and atomic mobility decreases. The viscosity change in the undercooled liquid may result in the formation of glassy state. As demonstrated in previous papers [I-21, in solidification involving surface nucleation of the product phase, as the case is in rapid quenching by melt-spinning, both nucleation temperature and nucleation time depend upon the number of atoms available at the isothermal surface in contact with the substrate. As a result of the thinness of the melt-spun ribbons, the embryo clusters that form at the freezing temperature may not be supplied by the amount of atoms necessary for their growth to critical nuclei sizes. In such extreme conditions, the liquid does not crystallize, it forms a metallic glass. A numerical simulation method is proposed for the reactions involved in embryo cluster formation and growth, at the atomic level. The simulation enables the caIcuIation of either the nucleation or the glass transition temperatures. Calculations made for the well-known glass forming CuZr and FeB systems afford prediction of the geometrical and thermodynamically conditions necessary for the formation of either crystalline or amorphous ribbons in melt-spun ribbons.

Jan 1, 1994

By Ker-Chang Hsieh

Four three-phase equilibria and one two-phase equilibrium in the FeNi- S-0 quaternary system in the vicinity of 1023 K and Pso2 = 1 atm were studied using the following emf cell 2 Pt,o2 (air)Zr02 .CaO/Pso2 = 1 atm, mixture of phases, Au The four three-phase equilibria are sp + (Fe,Ni )S + Ni 3s2, sp + Ni 3s2 + NiO, sp + NiO + N1S04 and Fe2 o3 + sp + (Fe,NOS04 -Y:he two-phase equilibrium is sp + (Fe,Ni)S. The two-.phase equilibrium was measured by using mixtures containing a major portion of one phase and a minor portion of the other. The results are presented in terms of oxygen potential as a function of YNi = nNi/(nN1+nFe) at constant temperature and pso2 = 1 atm. The stability diagram was also calculated using appropriate thermodynamic models for all the pertinent phases. The calculated diagram is in accord with the measured ones.

Jan 1, 1985

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don&apos;t allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir&apos;s law is discussed for different operating conditions.

Jan 1, 1996

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By Mukesh Jain

The liquor from potroom wet scrubbers is treated with lime to precipitate the soluble fluorides. The solids after filtration, referred to as scrubber mud, contain in addition to calcium fluoride, alumina, carbon, tars including polyaromatic hydrocarbons (PAH), cryolite and pachnolite and are considered hazardous. This communication deals with the pilot plant scale calcination of scrubber mud with a rotary kiln to obtain non-hazardous fluoride raw materials. Air classification was performed to separate the mudinto aluminarich andcalcium fluoride rich fractions which were then calcined. With proper control of calcination parameters and addition of lime, the carbon and tars were destroyed and hydrogen fluoride emissions were controlled. The calcined products could be used in the steel indusny as a fluxing agent or as a substitute for fluorspar in the production of aluminum fluoride.

Jan 1, 1994

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Corby G. Anderson

Hydrometallurgical technology for the pretreatment of refractory gold concentrates has been developed at Sunshine Mining and Refining Company. It employs a patented nitrous-sulfuric acid pressure leaching process which&apos; was proven industrially at the Sunshine refinery. Additionally, pretreatment for removal of antimony and some other impurities is done with alkaline sulfide leaching. This paper will discuss the successful application of these two technologies for pretreatment of a refractory gold concentrate prior to CIL gold recovery. A complex gold concentrate composed of pyrite, arsenopyrite and stibnite was tested. Results of antimony leaching in alkaline sulfide media will be discussed including some details of a novel and selective recovery method for gold leached by polysulfide or thiosulfate" Also, the factors important in and the results of the application of nitrogen species catalyzed pressure leaching to refractory gold concentrates will be detailed.

Jan 1, 1996