Search Documents

Reduction of titania and ilmenite ores by Cf4-H2-Ar gas mixture was investigated in a laboratory fixed bed reactor. Titania was reduced to titanium oxycarbide in the temperature range of 12OO-1500°C. At 1400-15000C, the extent of reduction of titania to titanium oxycarbide achieved more than 85% in 90 min. Optimum conditions for titanium oxycarbide synthesis by reduction of titania include temperature in the range of 1300-1450°C, methane content 8 vol% and hydrogen content above 35 vol%. Ilmenite ore was reduced by Cf4-HrAr gas mixture to metallic iron and titanium oxycarbide. Metallic iron catalyzed methane cracking and solid carbon deposition. Titanium oxycarbide formed at temperatures as low as 950°C. The optimum temperature for reduction of ilmenite is 1200°C and the optimum methane content is 8 vol%. Increase in hydrogen content increased both rate and extent of reduction. With 5 vol% CH4-75 vol% Hr20 vol% Ar gas mixture, the reduction of ilmenite completed in 60 min. Reduction of titanium oxides to oxycarbide with following chlorination may be an efficient alternative technology for processing of titanium minerals.

Jan 1, 2001

By Y. W. Chung, W. I. Chia

"The interaction of water vapor with single crystal Ni3(Al,Ti) and polycrystalline Ni3Fe, with and without the presence of oxygen, has been studied with Auger electron spectroscopy, photoemission spectroscopy, thermal desorption and isotope exchange. Water dissociates to produce atomic hydrogen above 200 K on both Ni3(Al,Ti) and Ni3Fe surfaces. For Ni3(Al, Ti), the reaction is structure-sensitive. Pre-adsorbed or co-adsorbed oxygen on Ni3(Al,Ti) and Ni3Fe significantly suppresses hydrogen production due to water dissociation. This suppression process occurs more efficiently on Ni3Fe than Ni3(Al, Ti).IntroductionOrdered intermetallic compounds such as aluminides, silicides and titanides are very attractive for structural applications at high temperatures. This is because these intermetallics tend to form adherent oxides in oxidizing environments which protect the base materials from excessive oxidation and corrosion. In addition, they have low density, relatively high melting points and good high-temperature strength. However, the moisture in air severely embrittles many ordered intermetallics such as FeAl [1-3], Fe3A1 [4,5], C03Ti [6,7], (Co,Fe)) V [8], Ni3Si [9], Ni3(Si,Ti) [10], Ni3(AI,Mn) [Ill, and Ni3A1 [12-14], resulting in low 'ductility and brittle fracture at room temperature. Recent studies by Liu and coworkers (see review by George and Liu [15]) provide a qualitative description of the mechanism for this moisture-induced embrittlement. During elongation testing, cracks are formed, thus exposing fresh alloy surfaces. One or more active components of the alloy react with water vapor in the environment to produce atomic hydrogen which penetrates into crack tips and causes hydrogen embrittlement. This is similar to that proposed for moisture-induced embrittlement of aluminum alloys [16]."

Jan 1, 1996

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999

By Michael Sheedy

Recoflo® ion exchange technology utilizes fine mesh resin beads, a fully packed resin bed, and counter-current regeneration. These unique features help to improve exchange kinetics, reduce regenerant consumption, and increase the concentration of strip solutions. Commercially, Recoflo technology has been extensively used in the following areas: the separation of strong mineral acids from dissolved metal salts, the purification, removal and recycle of dissolved metals in the surface finishing industries, and the production of high purity water. In the mining and metallurgical industries Recoflo ion exchange systems have been installed to treat a copper refinery bleed stream at Falconbridge's Kidd Creek plant and to treat a nickel and cobalt bearing ammonium sulfate effluent stream at another primary metal producer's facility. In the first application an APU® Recoflo system is used to separate the sulfuric acid at 200g/L from the dissolved copper and nickel sulfate salts at 80 g/L. The absorbed sulfuric acid is recovered from the resin by elution with water and is then returned to the refinery electrolyte circuit. In the second application a chelating ion exchange resin is used to remove nickel and cobalt at 0.01 - 3.0 g/L from process streams containing 120 - 240 g/L ammonium sulfate. This Recoflo system has been designed to reduce the nickel and cobalt levels to 0.001 - 0.002 g/L while recovering cobalt and nickel at concentrations up to 30 g/L and 15 g/L respectively. Case studies for both these metallurgical applications and other Recoflo processes are presented in this paper.

Jan 1, 1998

By Fuming Wang, Xin Lu, Hao Bai, Hebin Zhu

"In this study, CO2 emissions and carbon footprint of a typical steel works with integrated process and iron and steel industry in China was calculated and analyzed by a carbon footprint method based on the model of process CO2 emissions in iron and steel making. The carbon footprint of iron and steel industry from 1991 to 2010 in China showed a rapid increasing tendency. In 2008, the CO2 emissions of iron and steel industry in China was 1.289 billion tons, 19.71% of the national total CO2 emissions, and the corresponding carbon footprint was 159.13 million hm2 of green area. Carbon deficit of iron and steel industry also go up gradually if considering the carbon storage by green vegetation. Thus, the internal carbon reduction strategy, such as energy structure optimization and energy saving technology, was mainly encouraged for the sustainable development of iron and steel industry in China.IntroductionThe Global Warming resulting from the increase of Greenhouse Gases (GHGs), in particularly CO2, in the atmosphere has become the main reason of global climate change, and large emission reductions are required for sustainable development [ 1]. The iron and steel industry is the largest energy consuming manufacturing [2] in the world and the largest emitter of CO2 emissions. In 2005, it accounted for about 20% of global industrial energy use and 30% of energy and process CO2 emissions from industry [3]. In China, the crude steel has firmly been ranking at first of the world recent years and kept growing tendency year by year. With the production growth, the CO2 emissions of iron and steel industry also increased significantly and hence the steel industry has become one of the most sources of CO2 emission in China [4], which has attracted more and more attention to seek the carbon reduction strategies.Carbon footprint is an important and useful concept originating from Ecological Footprint, which was used efficiently to quantitatively analyze the impact of the human activities on ecological system, in particularly impact of the human energy activities [5]. In the view of Life Cycle, the carbon footprint is efficient to analyze the direct and indirect CO2 emission in the whole life of various products used in human activities. As to the iron and steel, the important materials and products in the human life, the carbon footprint analysis is quite necessary to evaluate the CO2 emission impact on the corresponding ecological system and global environmental."

Jan 1, 2013

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake's Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Ji-He Wei

The ESR of Cu-Cr-Zr alloy has been experimentally investigated. The remelting experiments have been carried out with different slag fluxes in the Cal, + Nal, CaF2 + ZrO2 and CaF2 + NaF + ZrO2 systems on an ESR furnace of 25kg capacity; using a water-cooled copper mould of 96.5 mm diameter, with the forged square bar electrodes of 50x50 mm2. The slag amount was taken to be 1.5 kg. The remelting current and voltage used were 1600-1800A and !5-25K, respectively. The influence of the slag composition on the stability of the remelting process and the losses of alloying elements (2r and Cr) has been considered and examined. The technologies of hot working and heat treatment of the ES ingot have been described and discussed. Some physical properties of the slag in a CuF2 + NaF + ZrO2 system and the remelted Cu-Cr-Zr alloy have been determined. The results indicated that with the slag flux of CaF2 + NaF + l0 mass % ZrO2 and the other operation parameters employed, a high quality ingot of Cu-Cr-Zr alloy may be obtained at the considerably high yields of Zr and Cr by means of ESR. For the remelted Cu-Cr-Zr alloy with a specified composition of 0.5 mass % Cr and 0.1 mass % Zr, the appropriate electrical conductivity, hardness and softening temperature are as high as 45-46S/m, HRB 82-84 and 550°C. respectively. The properties of the Cu-Cr-Zr alloy products are in accordance with and superior to the requirements and specifications of ISO5l82-l99l(E).

Jan 1, 2000

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By D. A. Horne, V. R. Daiga

Certain steel mill wastes contain significant amounts of zinc oxide due to the use of galvanized scrap during the steel making process. Typically electric arc furnace (EAF), and basic oxygen process (BOP) flue dusts contain 20 to 30% zinc oxide and 40 to 50% iron oxides, along with smaller quantities of lead and cadmium. These materials can be recovered from the flue dusts by using a proven rotary hearth furnace (RHF) process. By-products of the recycling operation include a crude zinc oxide fume, which is captured in a baghouse filtering system, and sponge iron that may be recycled into the steel making operation. Crude zinc oxide properties plus the operating experience from two commercial RHF installations utilizing MR&E's DRyIron™ Process will be presented.

Jan 1, 2000

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006