Search Documents

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By Wayne Bell, Matthew Andriese, Shuqian Xie, Jiann-Yang Hwang, Zhiwei Peng

"Pyrolyzed carbons are generally known as good microwave absorbers and their dielectric properties still remain to be fully explored. In the present study the dielectric properties and dielectric polarization-relaxation phenomenon of a typical activated carbon was investigated. The experimental results indicate the complex permittivity is highly dependent on temperature and frequency. The decrease of permittivity with increasing temperature from room temperature to ~100 °C is probably ascribed to the release of the water vapor adsorbed on the surface of activated carbon, and the variations of permittivity with temperatures between 100 °C and 450 °C in the frequency range of 300 MHz to 3000 MHz are mainly attributed to the decreased relaxation time of dielectric polarization.IntroductionPyrolyzed carbons have been identified as excellent microwave absorbers owing to their high dielectric and electrical loss under microwave irradiations. Among them, activated carbon continues to attract more and more attention from researchers. Due to its special physical properties, the production, modification and regeneration of activated carbon with the assistance of microwave have been widely studied over the last few decades [1-6]. However, only few attempts have been applied to explore the dielectric properties of such materials due to the complexity and variability of their organic precursors and activation processes [7,8]. In order to shed a light on this problem, a typical sample, Norit® A Supra USP powdered activated carbon, was adopted to perform dielectric characterization, which may provide useful information for its wide application in the fields of purification, energy (hydrogen) storage and so on."

Jan 1, 2011

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By Yimin Ruan

"An inverse design method is developed to obtain the optimal cooling conditions for the continuous quenching of precipitation hardenable sheet alloys to achieve the required yield strength. The yield strength of a precipitation hardenable alloy is obtained by allowing solute to enter into solid solution at a proper temperature and rapidly cooling the alloy to retain the solute in the solid solution. An aging process may be needed for the alloy to develop the final mechanical properties.The objective of the design is to optimize the quenching process so that the required yield strength can be achieved. With the inverse design method, the required yield strength is specified and the sheet thermal profile at the exit of the quenching chamber can also be specified. The conjugate gradient method is used to optimize the cooling boundary condition during quenching. The adjoint system is developed to compute the gradient of the objective functional. An aluminum sheet quenching problem is presented to demonstrate feasibility of the inverse design method.IntroductionQuenching is a critical step in metal production to achieve desired material properties, such as yield strength, hardness, etc., for precipitation hardenable alloys. In most cases, rapid quenching from the solution heat treatment temperature is necessary to obtain the required material properties, but rapid quenching may cause other problems such as excessive distortions of the quenched materials.In a solution heat treatment, the alloy is heated to a suitable temperature, held at that temperature to allow the soluble alloying elements to enter into the solid solution, and cooled rapidly (quenching) to retain the alloy elements in the solid solution. An aging process, which controls precipitation of fine particles at room (natural aging) or elevated temperatures (artificial aging), is generally followed after the quenching process to develop the final mechanical properties of the heat treated alloys."

Jan 1, 1998

By R. Cavanagh

Studies relating to the fixation of sulfur by reaction of 4 to 8 mm diameter cylinders of calcined limestone or dolomite with high strength sulfur dioxide in the temperature range 880°C to 1020°C were undertaken. Dolomites are far superior in sulfate capacity and reactivity than dense limestones even at high strength SO2. The sulfation reaction was first order with respect to SO2 concentration below 100 percent. Zero reaction rate at 100 percent SO2 concentration indicates that sulfate was the exclusive reaction product and that sulfite had no role in the reaction. At relatively low SO2 concentrations gaseous diffusion through the reaction product layer has a marked effect on the rate. As SO2 concentrations were increased up to 100 percent more complex rate controlling mechanisms unfold. By sectioning partially reacted dolomitic limestone pellets a moving interface was observed. Reaction ceased because of pore plugging for dense non-porous limestones at 30% conversion. With dolomitic material virtually complete sulfation of the calcium was observed. S.E.M. analysis showed that the average atom ratio Ca:S was 1.01, thus supporting the argument that little if any of the magnesium was sulfated.

Jan 1, 1996

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991

By R. Y. Wan, S. L. Chryssoulis

"Gold associations were established in a·biooxidized, chlorinated CIL residue assaying 0.02 oz Ault and in a biooxidized thiosulfate leach residue assaying 0.01 oz Au/t. A detailed mineralogical study involved: assays of screened fractions; light microscopy; ion probe microanalysis to quantify 'invisible' gold in sulfide minerals; proton probe microanalysis to detect and quantify preg-robbed gold. In the CIL residue, most of the gold is preg-robbed (71 %). In the thiosulfate leach residue, gold occurs mainly as submicroscopic disseminations in microcrystalline quartz (chert). In both residues, the 'invisible' gold in pyrite accounts for a minor fraction of the gold assay. Quantitative determination of the gold occurrence in the two residue samples established conclusively that gold adsorption on carbonaceous matter in the thiosulfate leach is of minor importance.Acknowledgement: published with permission of Newmont Gold Company."

Jan 1, 1997

By Miroslav Raudensky, Kallol Bera, Jaroslav Horsky, Jee G. Chang, Ampere A. Tseng

"A combined experimental and finite element approach to study the local heat transfer coefficient is presented in this paper. The heat transfer coefficients at different cooling regimes in a roll are quantified by an inverse heat conduction technique; the heat transfer phenomena involved are then discussed. A discussion of the application of the heat transfer information found in the present study for better design of a roll cooling system is also included. Finally, an identification of areas where further work is needed is presented.IntroductionIn metal rolling processes, the roll is used as a tool to deform the workpiece at very high speeds. As shown in Fig. 1, the heat transfer phenomena involved in the process are complicated by the interaction between the roll and the strip, mainly including 1) the heat transferred from the workpiece to rolls in the contact regions, 2) the heat created in the interface due to the deformation of the workpiece and the friction between the workpiece and roll, and 3) the heat removed by watercooling as well as the ambient air. All of these transport phenomena occur at extremely high pressure, high speed, and high heat flux; these make the control of the roll temperatures an extremely challenging problem.In hot rolling, proper cooling of rolls can lead not only to improve the roll shape quality by controlling the thermal crown of the roll, but also to extend the roll life by minimizing the thermally induced stresses [1,2]. Also, knowledge of roll temperatures can contribute to insights about the roll/workpiece interfacellubricant behavior, and lead to the desired surface condition of the workpiece. Therefore, adequate roll cooling or control of roll temperatures is of critical concern to mill designers and process engineers. In order to have proper operation of the process, a good understanding of the influence of cooling practices on the roll is essential [3]."

Jan 1, 1994

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

The rare earth elements are essential for a diverse and expanding array of high-technology applications, which constitute an important part of the industrial economy of the 21st century. As a matter of fact, rare earth has been listed in the category of strategic elements in many countries becoming a core business for international research. Experimental tests have been carried out on a bench scale battery of mixer settler composed of 24 stages, each one with a volume of 150 ml. These trials have been performed at room temperature checked by a micro-climatic control system. The battery was setted in two sections: extraction and scrubbing section. Rare earths concentrations were obtained by ICP-OES analysis made on aqueous phase and on the stripped from organic phase. We obtained a complete separation of light rare earth (La, Ce, Pr, Nd) in two sub-groups: La/Ce and Pr/Nd.

Jan 1, 2014