Search Documents

By Wen Liangying, Zou Chong, Tan Xiuqin, Bai Chenguang, Zhang Shengfu

"Eight typical metallurgical byproducts containing iron were selected based on the effect of the chemical composition, particle size, additives on the burnout degree of pulverized coal. Effect of three typical byproducts including fine iron ore, BOF dust and BOF sludge on combustion reactivity and combustion efficiency were investigated using TG-DSC method. The results indicated that the three additives have obvious catalytic effects on pulverized coal. By comparison, the relative active sequence of byproducts to the catalytic combustion can be described as follows: BOF dust>BOF sludge>fine iron ore. Moreover, adding BOF dust as component of additives also shows significant catalytic effects on combustion efficiency during rapid heating process.IntroductionChina is the largest producer in the world with an annual output reaching over 6 billion tons. Solid wastes arising from iron and steel making increases the environment pressure in recently years. For instance, annual output of dust during the production of iron and steel making in China reach up to 5 million tons, which is close to 8%~15% of the amount of steel [1]. Another characteristic of these byproducts is they are finer particle which are just harder to deal with. Since some of solid wastes, including dusts, scales, and sludge, usually contain high iron content, sintering plants have traditionally been used to recycle byproducts in integrated steel plants in China. However these byproducts also have noticeable effects on sinter quality, sinter strength and productivity and, therefore, waste recycling is limited depending on the analysis of the waste materials [2]. Another method which is pre-treatment of byproducts in pelletizing process, increases of energy consumption and production cost. In addition, metallurgical byproducts often contain heavy metals and alkalis. For these reasons, recycling rate of the byproducts in China is very low. Therefore, how to recycle the byproducts in iron and steel making process is an important subject."

Jan 1, 2012

By V. J. Ramirez, A. M. E. Noguez, M. J. Navarrete, B. G. Salas, N. T. Robert

"The close die forging stress in truncated conical cavities is evaluated with dimensional analysis. Five dimensionless groups are proposed from the process variables in order to simplify the forging stress determination. These groups are experimentally related and graphically expressed. This methodology can be used to predict the actual forging stress in industrial close die forgingThe use of the dimensionless groups allow to comprise more cases than the presented here, provided similar geometries and operational conditions.Introduction.Closed die forging is essentially a plastic deformation inside a two piece mold (forging die) with the inverted shape of the actual forging geometry. This plastic deformation will always be the result of a compressive stress. There are theoretical models which include complex calculations for the analytical determination of stresses (1, 2, 3, 4). Results of these calculations are approximate, requiring generally ulterior tests to obtain the true operational conditions(5).In this paper, it is presented a simplified approach to the actual compression stress needed in the forging. A well known tool in engineering: the Buckingham's Pi theorem in conjunction with dimensionless groups and a working piece scale model is used. Dimensional analysis will give the dimensionless terms needed to experiment with a selected scale model geometry to make the stress determination. The results presented demonstrate the reliability of this methodology."

Jan 1, 1997

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study reactions of sulfidic nickel particles. The studied materials were three natural nickel concentrates and four synthesised nickel mattes. The variables of the experiments were the gas preheating temperature (500 - 1300°C), the composition of the reaction gas (N2 + 0 - 75 vol-% 02) and the ,particle size of the feed. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect alteration in their morphology, internal composition and structure. General reactivity of the materials was monitored by the extent of sulfur removal. The reaction mechanism of the studied materials was found to depend primarily on the materials composition as well as oxygen content of the reaction gas.

Jan 1, 1998

Heap leaching with thiosulfate is only used in one location for the treatment of a refractory preg-robbing gold ore initially pre-treated with bio-oxidation. The chemistry of thiosulfate leaching is complex. Further work is required to develop a better control of the system. A mild refractory gold ore containing pyrite and chalcopyrite was used in this study to investigate the use of thiosulfate as an alternative heap leaching technology. Preliminary bottle rolls tests indicated that similar gold extraction was obtained with cyanide and thiosulfate. In the column leach test, effects of thiosulfate, copper and ammonia concentrations, and their ratio on both gold extraction and reagent consumption, were assessed. The range of reagent concentration were: 0.1 - 1.0M (NH4)2S2O3, 0.03 - 0.10M CuSO4*5H2O, 1.0 - 6.0M NH4OH. The solid-liquid ratio was in the range of 0.83:1 to 5: 1. Best results showed that 72% of gold was extracted in 50 days with 0.3M (NH4)2S2O3, 0.05M CuSO4*5H2O and 6M NH4OH or a combination of 1.0M (NH4)2S2O3, 0.03M CuSO4*5H2O and 3M NH4OH. The reagent consumption at solid/liquid ratio of 3:1 was 37 - 48.6 kg/t (NH4)2S2O3 and 0 - 0.62 kg/t CuSO4*5H2O. The results of thiosulfate leaching were also compared with cyanide leaching.

Jan 1, 1999

By Sabine Knott

The thermodynamic properties of four liquid ternary zinc alloys, Au-Sn-Zn, Ag-Sn-Zn, AI-Sn- Zn and Cu-In-Zn were measured with an electromotive force (emf) method at three or four cross-sections with an constant X:Sn or Cu-In ratio. At the Au-Sn-Zn and AI-Sn-Zn system calorimetric measurements were also carried out in order to compare the integral enthalpy of mixing from the direct measurements with the data of the emf measurements, which were derived by Gibbs-Duhem integration.

Jan 1, 2003

By Sabine Knoll

The thermodynamic properties of four liquid ternary zinc alloys, Au-Sn-Zn, Ag-Sn-Zn, AI-Sn Zn and Cu-In-Zn were measured with an electromotive force (emf) method at three or four cross-sections with an constant X:Sn or Cu-In ratio. At the Au-Sn-Zn and AI-Sn-Zn system calorimetric measurements were also carried out in order to compare the integral enthalpy of mixing from the direct measurements with the data of the emf measurements, which were derived by Gibbs-Duhem integration.

Jan 1, 2003

By A. Kar

A mathematical model is presented for pure titaqium deposition from titanium tetrabromide on a stainless-steel (SS 304) substrate. Five three-dimensional, transient, and nonlinear partial differential equations are used to account for the diffusion of various species inside the deposition chamber and the thermal decomposition of titanium tetrabromide, titanium dibromide, and titanium monobromide at the surface of the substrate in order to determine the thickness of the titanium film deposited on the substrate. The effects of various process parameters on the deposition and shape of titanium films are examined, and under certain conditions, the deposited titanium films are found to have volcanic profiles.

Jan 1, 1992

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Jesús Contreras

Since the commencement of its activities in Huelva in 1970, Atlantic Copper has maintained a course of action that has been more demanding than the successive environmental legislations current at different times. As its primary objective it has sought compatibility between the protection of the environment and both its industrial activity and the social and economic development of the area in which its Metallurgical Complex is located. For this reason, since the seventies it has maintained a continuous programme of investments which have allowed it to attain its present environmental situation. As a consequence of the Environmental Policy of Atlantic Copper, in April 1998 it obtained certification for its Integrated System of Environmental Management (SIGMA) according to international standard IS0-14001, and under European Community Regulation 1836/93 (replaced by the 76112001) for the Eco-Management and Eco-Audit System (EMAS). The SIGMA formalises the environmental management practices of Atlantic Copper and engages it to have available a system that can be fully audited. Atlantic Copper was the first European Company in the non-ferrous metallurgical sector to obtain both the UNE-EN-ISO 14001 certification and the EMAS registration. The present paper reviews the actions by Atlantic Copper in environmental matters that have allowed it to achieve its present position. It also describes the coming stages of improvement planned and the modifications to be carried out in the near future, in particular the criteria for the selection of technologies on the basis of the concept of BAT (Best Available Techniques) introduced by the European Union, and always guided by the final objective of converting Atlantic Copper into a reference within the sector, comparable to the best designed and operated installations in the world.

Jan 1, 2003

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Ken-ichi Machida

"Surface modification of R-Fe-N intermetallic compounds was made to improve their magnetic property and nitrogenabsorbing ability, arid high-performance resin-bonded magnets and nitrogen storage materials were developed: Surface coating for Sm2Fe11Nx by the zinc metal produced via photodecomposition of Zn(C2Hs)2 was effective to avoid the further oxidation in the molding process of the fine powders for bonded magnets and the resulting (BH)max values were improved to -186 kJm-3. Meanwhile, R2Fe17 as the mother compounds for RzFe11Nx was highly active for decomposition of NH3 molecule and subsequent nitrogen absorption as metal nitrides. Furthermore, even inert Nz molecule was dissociated on them by impregnating Ru metal and the resulting nitrogen atoms were absorbed in the crystal lattice of R2Fe17. These results demonstrated that the nitrogen storage system was established by cycling the nitrogenation and hydrogenation of RzFe11/R2Fe11Nx materials.IntroductionProcessing for rare earth metals and intermetallic compounds requires well-controlled conditions in order to avoid the oxygen contamination involved in it due to their high reactivity, as causes the serious damage for materials such as magnets, metal hydride for hydrogen storage, and so on. Rare earth-iron intermetallic compounds, R2Fe17, provide the corresponding metal nitrides (R2Fe11Nx) by heating in N2 or a mixed gas stream ofNH3-H2 [l] and, among them, Sm2Fe11N3 has been particularly noted as one of the promising materials for high-performance permanent magnets such as bonded ones [2- 6]. Usually, the nitrogenation for Sm2Fe17 is made in Nz, but it needs the much more hard conditions of reaction pressure (-10 MPa), temperature (-550°C) and time (-72 h) than the nitrogenation in the NH3-H2 mixture [l]. In the latter case, a significant amount of nitrogen can be interstitial introduced in· the R2Fe17 crystal lattice (x=-7) under the more moderate conditions than in N2 (at 0.1 MPa and -450°C for -3 h) [3-6] and then, in a similar manner as metal hydride systems [7], the excess nitrogen in RzFe1 7Nx (x>3) is reversibly desorbed by heating at a temperature around 500°C in Ar to form the RzFe11N3 compounds. This behavior of nitrogen absorption and desorption has a close relation to the sites for nitrogen in the crystal lattices."

Jan 1, 2000

By Saad Elias Kaskah

"The Box-Behnken Design (BBD) is used to model the sacrificial Cathodic Protection System (SCPS) to find the factors effectiveness behaviour. For protection potential assessment the BBD receives (resistivity of environment, sacrificial anode alloy, distance between anode and cathode and surface area for the structure to be protected) as input and gives the protection potential as output. By applying BBD with their analysis tools we get many results. The important results which are the factors individual effectiveness on the sacrificial cathodic protection (SCP) process are the resistivity which has the greatest effect on the potential protection (rank=l) followed by sacrificial anode alloy type (rank=2), surface area for structure protected required (rank=3) and distance between anode and cathode (rank=4). The interaction of sacrificial anode alloy and cathode area {X2X4 ) has significant effect on CP process with the limits which are used in this work while the other factors interaction (X1X2, X1X3, X1X4,X2X3, X3X4 ) has insignificant effect on the limits which used in this work.IntroductionFor carbon steel in seawater the normal corrosion potential E '°""_is in the range -550 to -600 mV vs. Ag/AgCI [1]. The most effective method to overcome the corrosion is cathodic protection {CP) which represents a control method in the steel wall corrosion. Cathodic protection has been used in several areas including marine and underground structures, storage tanks, and pipelines [2]. Sacrificial anodes system generates protective current which depends upon the inherent potential difference between the anodes and the structure to be protected. If the structure is made of iron or steel, any metal that is more active in the electromotive force series can theoretically be used as anode material [3]. There are many factors influencing on cathodic protection like resistivity (NaCl content), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode, temperature, humidity, velocity of solution, dust, impurities, bacteria and etc .. The present work studied four factors: NaCl content, resistivity), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode) with different three levels of values for each one. Then this work will find the optimum value from the factors levels that tacked to investigated there influencing on sacrificial cathodic protection system."

Jan 1, 2013

By Wenjun Duan, Qingbo Yu, Qin Qin, Junxiang Liu

In the study, the coke-oven gas (COG)-steam reforming process using hot blast furnace slag (BFS) as the heat carrier is explored for producing hydrogen and recovering high-grade waste heat of hot BFS. The method of the Gibbs energy minimization approach through Lagrange multiplier is adopted in the thermodynamic analysis of reforming process. The simulation is carried out to study the operation pressure, temperature and steam to carbon ratio (S/C) based on the chemical equilibrium calculations. The optimal operation conditions are determined to improve the yield and fraction of hydrogen in the COG-steam reforming process. The results suggest that the preferential operation conditions for COG-steam reforming process to produce hydrogen are achieved at 600ºC, 1.5MPa and S/C (5.0). Due to the CaO and other melts in BFS, CH4, CO and CO2 in COG are converted and removed efficiently, especially CO2. The hydrogen fraction reaches to 86.7% and its production is about 1.22mol with 1mol of the COG.

Jan 1, 2016

By C. Burton Clark

The important role of the petrographic microscope in the petrology of refractories is discussed, based on 45 years of industrial experience by the author. Highlights of his career are used to illustrate improvements in equipment and techniques during the period. Two specific investigations are described which emphasize the interrelated use of the petrographic microscope with other instruments such as the x-ray diffractometer and scanning electron microscope. Emphasis is placed on the use of phase equilibrium diagrams for guidance in predicting and interpreting reactions that occur under non-equilibrium conditions in the manufacture and use of refractories.

Jan 1, 1982

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By L. A. Harris

In the present study the open gradient magnetic separation' (OGMS) method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy (SEM) and x-ray diffractometry (XRD) were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (-80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

Jan 1, 1981

By Baozhong Ma, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The effects of additives with Na2S, Na2SO4 and CaSO4 on phase transformation of nickel laterite ore in low-temperature reduction roasting process using carbon monoxide were investigated. The results showed that diffraction peaks of forsterite increased with increasing reduction temperature for 30min with the addition of 10wt% Na2SO4 and 50vol% CO, and diffraction peaks of forsterite increased with increasing the content of Na2SO4 at 900°C for 30min. Comparing the above three additives, phase transformation of nickel laterite ore were strongly influenced with the addition of 10 wt% Na2SO4 and 10 wt% Na2S. Calcium sulphide from the thermal decomposition of CaSO4 was carried out in the reaction product. SEM-EDS analysis result deduced that increasing the dosage of Na2SO4 from 10wt% to 15wt% could promote the polymerization of ferronickel and improve the grade of nickel in ferronickel.

Jan 1, 2015