Search Documents

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

The Rasmussen Ridge phosphate mine is owned by Agrium CPO and operated by a unit of Washington Group International. The mine, located in southeastern Idaho, received the Idaho Inter-Agency Reclamation Award from the Idaho Department of Lands. The phosphate mine, located northeast of Soda Springs, was honored for “Excellence in Ongoing Operations, Soft Rock Mines over 75Acres.” Charles Ross is Agrium CPO’s plant manager. He said, “We are honored to receive this award. This recognizes the commitment and dedication of our employees toward the protection of the environment. I am really proud of the people that work at the mine.”

Jan 1, 2005

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By J. Garretson

When mining accidents occur, workers often become trapped and/or incapacitated. Current rescue operations can be dangerous and too slow to produce favorable outcomes. Currently, no method exists for rescue crews to scout ahead at critical times to assess the situation. Sandia National Laboratories (SNL), through a National Institute for Occupational Safety and Health (NIOSH) sponsored program has developed the Gemini-Scout mine rescue platform. The Gemini-Scout was created to assist in underground mine rescue missions. It has been designed to go into potentially hazardous environments to assess the conditions (structural, air quality, temperature). In addition, it will enable two-way communications with potential survivors prior to human rescue teams being able to enter the area. The Gemini platform is a dual tracked-chassis design, which gives the robot excellent mobility in unstructured environments. The design includes a passive 2-degree of freedom joint between two identical bodies allowing for ±30deg of pitch and roll. In addition to the base mobility platform, the Gemini-Scout incorporates many other features to help it succeed in its underground mission. The electronics are mounted in explosion proof housings to ensure safe operations in hazardous gas environments. The platform is also able to operate in up to 18in of standing water with its elevated pan/tilt cameras for navigation. A four-channel video link and Two-way audio on the vehicle help to ensure located survivors can communicate with the robot operators. The platform also incorporates a Mine Safety and Health Administration (MSHA) approved multi-gas sensor to monitor air quality. SNL believes that this technology is broad enough to be appealing to other first responders, such as police, firefighters and medical personnel. Gemini could easily be fitted to handle earthquake and fire scenarios, and it could provide relief in currently inaccessible situations.

Jan 1, 2012

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Yoneji Kanoh, Masahiko Ohtsuka

In Japanese tunneling history, it has commonly been accepted that the long-round driving is difficult due to the complicated geological condition. Therefore, the maximum past record has been less than 3 m per round. A new record of advance was established in the 99 m2 headrace tunnel of Imaichi Water Power Station Project with an advance of 239.5 m in a month by drilling 3.9 m deep blast holes. The geology of the headrace tunnel composed of pyroxine andesite (ie. 960-1770 kg/cm2, VP3.1-4.3 km/s) which had several clay seams and open cracks and was moderately weathered. Automatic shotcrete machine was used for shotcreting. Rock support was specified according to the N.A.T.M. with each different rock type. The contractor achieved a remarkable tunneling advance not earlier experienced in Japan.

Jan 1, 1983

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By Jerry D. Pfarr, Gary Loving, David G. McDowall

Introduction The Open Cut is one of the best known landmarks in South Dakota's Black Hills. It is the site of the original discovery of the Homestake ledge, or lead, in 1876. Between that time and 1945, the Open Cut produced about 36 Mt (40 million st) of gold ore, the majority of which was drawn from underground operations. In 1981, a drilling program was undertaken to determine how much ore the old timers left behind. The results of this study indicated an ore body made up of broken and caved ground, and solid blocks in pillars and crowns. Reserves are estimated at about 6.8 Mt (7.5 million st) of gold ore, grading at 4 g/t (0.116 oz per st). Total tonnage of material, including waste, is estimated at more than 60 Mt (66 million st). The mining plan is a combination open pit and underground operations. The bottom 78 m (255 ft) will be mined by the underground panel-caving method. The open pit was designed as a contractor operation up to the expected milling stage or the point of sustained ore production. The pit was designed to avoid disturbance of US Highway 85 near Lead, SD. In 1983, the South Dakota Board of Minerals and Environment approved the mining and reclamation plan. Test mining began in the north of the Open Cut using open pit methods. Upon completion of the test pit, Homestake Mining's board of directors approved an expanded mine plan. They committed an additional $27.1 million to prestrip the ore body that is expected to yield 23 t (750,000 oz) of gold. Project life is estimated at 15 years. Exploration program In early 1980, 10 diamond drill holes were drilled from the surface in the vicinity of the east side of the Open Cut. The reserves delineated by that drilling were too small to justify their development. A continuation of this study attempted to quantify the tonnage remaining in the bottom of the Open Cut in the crushed remnants of old stope-and-crown pillars. This was originally thought to be minable by improved drawhole methods using highly mechanized procedures. By early 1981, however, thinking turned toward surface mining methods. The effort to quantify minable ore tonnage ultimately involved drilling 385 reverse-circulation rotary drill holes. These were drilled from August 1981 to March 1983 in several groups of holes. Each group, or drilling program, had a slightly different immediate goal or purpose. The holes were drilled to various depths using truck-mounted Drill Tech 40 drills with doublewalled 76 mm (3 in.) pipe with 134 mm (5.25 in.) three-cone rotary bits. Initially, wet drilling was employed using a cyclone collection system. Since cutting recovery was not as high as it should have been, all subsequent drilling was dry. The cuttings were collected and deposited by way of a cyclone into the sample bag. The pickup for the cuttings using the three-cone bits was about 50 mm (2 in.) above the bottom of the hole. Overall cutting recovery for the drilling program was estimated at 75%. Samples were taken on each 1.5 m (5 ft) of hole drilled. Each sample was split into three 48-g (1-2/3 assay ton) charges. The accepted value was the straight average of the three charges. Because of the known "nugget effect," assays were nearly impossible to duplicate. Therefore, to validate the regular assays, a series of screen fire assays were run. Based on this method of assays and checks, it was concluded that 10% more ounces would be produced than indicated by mine grade. Test pit The northernmost portion of the mine as planned is known as the Terraville test pit. This portion was mined ahead of the rest and separately. It provided answers to questions on slope stability, reserves correlation, mill recoveries, mining costs, and surface mining conditions in various weather and ground conditions since many boulders and much timber were expected. The mining plan for this portion of the pit was successful. More ore was mined than was expected. Mixing of Open Cut ore with underground ore in the mill feed was successful. Impact on the surrounding communities

Jan 10, 1987

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once an analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at its power plants. A quality assurance program can also help a mine deliver a consistent product to a utility's power plants. The importance of accuracy, timeliness and consistency are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001