Search Documents

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By Q. Zhang, X. C. Wang, S. Mao

Phosphate ore is an important strategic mineral resource in which apatite is the main valuable mineral. Flotation is the most commonly used method to separate apatite from middle-low grade phosphate rock. Selective flotation separation is based on the difference of physical and chemical properties of minerals occurring at the three interfaces of mineral/bubble/water. Surface and interface chemistry of mineral have been playing an important role in interpreting and governing its flotation phenomenon. In-situ, visualized and high-precision analytical techniques, such as Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy and Molecular Simulation, have been applied to explore and uncover microscopic nature of apatite flotation. Consequently, a great progress at molecular or atomic level on surface and interface chemistry of apatite flotation has achieved in the past decades. In this paper, the research progress of surface and interface chemistry of apatite flotation such as surface wettability, surface-charging characteristics, surface dissolution behavior, adsorption mechanisms of fatty acid collector and depressor on apatite surface were systematically reviewed. This review will be helpful for the development of more selective reagents and efficient technologies for apatite flotation. Keywords: Apatite, Flotation, Surface and interface chemistry, Surface analysis technology

Jan 1, 2020

[The following notations will be used: O an ore body. z a point in O. z' another point in O. w0 (z) a point support of infinitely small dimensions w0 centred in z. w (z) a sample (or block) of finite dimensions kv centred in z. W (z) a block of size W greater than or equal to w. W'(z) a block of size W' greater than or equal to W. W" (z) a block of size W" greater than or equal to W'. x (z) value of the regionalized variable x with support wO at point z. p (z) average value of x in w (z). pw WZ) = E[x(z')l zt in w(z) pw (z) average value of x in W (z). pwl (z) average value of x in W' (z). pwU (z) average value of x in W" (z). Note that pW (z), pw (z), pwf (z) and pw,, (z) are (regular- ized) regionalized variables with support w, W, W' and W" respectively. The relative sizes of wO, w, W', W" and O are represented schematically in Fig. 7.1. The variance of pw (z) when w (z) takes all possible positions in O is known as the dispersion variance of w in O and is denoted by a? (w in O) or a\: 0; = a2(w in a = Ew,z, inn {[p~ (z) - p121. (7.1) For convenience, the following simpler notation will be used: a> Ew in n [(p w - pl21. Consider now a large block W (z) in O with average value p~(z), and all the possible smaller blocks (or samples) w (z') of size w in W (z). We can calculate the variance of the blocks w (z') in the block W(z), which is the dispersion vaciance of w in W (z), from the relationship a2 [w in W(z)l = Ewcz,, in W(Z) {[PW (z') -pw (z)l21. (7.2) Provided the intrinsic hypothesis is satisfied (§3.4.4), this variance is a function only of the dimensions of the supports w and W, and is independent of the position z of the block W (z). We can therefore define the dispersion variance of w in W, as follows: u2 (win W) = Ew in w [(ptti - PW)~]. (7.3) In cases where the intrinsic hypothesis is not satisfied, the variance of samples w in blocks W may vary only slightly from block to block, so that the average dispersion variance of w in W (z) for all possible W (z) in O can be used: ayw in W) = Ew(,, ~n n {a2 [W in W (z)]}. (7.4) The following example will help to illustrate the importance of the variance of dispersion. Assume that we plan to develop a bedded coal deposit Q. We consider mining the ore body with only one giant dragline, which will extract each day a block of coal of size W'. The total area mined in a year will have a size W". We want to know whether this scheme is acceptable, given that the daily variation in ash content must not exceed a given percentage specified in the sales contract, which is renewable on a yearly basis. On a given day, if we mine the block W' (z), the ash content will average pwT (z). In a period of one year, the expected daily variation in ash content is measured by the expected variance of pwf (z) in W", i.e. by a2 (W'in W"). An alternative mining method might be to use two smaller draglines, each one mining W'/2 of ore per day, and Wn/2 per year. If the draglines are used to mine two distinct sections of the deposit, the expected daily variation in ash content will be u2 (W'/2 in Wj1/2)/2 Other situations, where economic decisions cannot be made without knowledge of the dispersion variance, are illustrated in § 7.4 and 7.5 below. Remark: The notation a2 (w in W) is used in this publication because of its clarity. An alternative notation, which is increasingly accepted in the literature, is s2w/W. ]

Jan 1, 1978

By D. J. Briggs

The use of backfill for regional and local support is receiving increasing attention in the South African mining industry. To ensure that fill materials meet the purposes for which they are intended, a test procedure to characterize the load-deformation characteristics for a particular fill was developed. The major variables identified as influencing the load-bearing proper- ties of backfill include particle size distribution, porosity, width-to-height ratio, strain rate, confinement, water content, and additives. The influence of these variables on the performance of backfill is described in relation to crushed waste, dewatered tailings and deslimed tailings. These investigations confirmed that no single test could be used to define the overall stress-strain behaviour of a selected fill. Nevertheless, resulting from this work, a preliminary standard test procedure for uncemented backfill materials, com- prising a suite of tests in unconfined and confined compression, has been formulated. This test procedure is a significant advance towards a more meaningful evaluation of fill materials. Test results will also provide numerical information for input use in computer programs for the design of mine layouts incorporating backfill.

Jan 1, 1988

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

By B. Geelhoed

A generalization of Gy?s 1979 model for the variance of the fundamental sampling error has been proposed at WCSB2?2005 by Geelhoed. This generalized model can potentially lead to a better correspondence with actual sampling processes. However, a new parameter is required by the new model: ?the parameter for the dependent selection of particles?(Cij). It is important that this new parameter, which is at the basis of the new theory, is well understood in the sampling and blending community. In order to clarify the meaning of Cijand to prevent potential misinterpretation of Cij, we discuss the difference between Cij and an intuitively associated, but different, parameter: ?the parameter for the dependent selection of particle types?(Mij). In this contribution, the theoretical difference between both parameters is clarified. Simulations demonstrate that, numerically, the difference between Cij and Mij can be large. Some additional advantages of the approach which uses Cij are discussed: (i) the approach based on Cijis more general; (ii) in all cases where Mij is known, Cij can be determined as well, while the reverse is not true; (iii) an equation already exists that relates the sample variance to the value of Cij.

Jan 1, 2009

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By G. Akdogan, I. Mwandawande, S. M. Bradshaw, M. Karimi

The mixing characteristics of industrial flotation columns were investigated using computational fluid dynamics (CFD). Particular emphasis was placed on the clarification of the relationship between the liquid and solids mixing parameters such as the mean residence time and axial dispersion coefficients. The effects of particle size and bubble size on liquid dispersion in the column were also studied. An Eulerian-Eulerian method was applied to simulate the multiphase flow, while additional scalar transport equations were introduced to predict the liquid residence time distribution (RTD) and particle age distribution inside the column. The results obtained show that particle residence time decreases with increasing particle size. The residence time of the coarser particles (112.5 μm) was found to be at least 60% of the liquid residence time, while the finer particles (19 μm) had a residence time similar to the liquid. The results also show that an increase in the particle size of the solids results in a decrease in the liquid vessel dispersion number, while a decrease in the bubble size increases liquid axial mixing. Finally, the simulated axial velocity profiles confirm the similarity between the liquid and solids axial dispersion coefficients in column flotation.

May 2, 2022

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By B. Emwanu, R. A. Raju

The implementation of new technology in mining can be likened to a paradoxical situation or dilemma, where, on one hand, major mining projects are not able to solicit investor funding unless it is proven that the business cases were developed using tried and tested mining methods. On the other hand, new and innovative mining technology and mining methods need first to demonstrate and prove themselves under real production conditions over a reasonable period before they can be considered bankable feasibility studies in the mining industry. This dilemma locks new mining technology investments in a continuous cycle of underinvestment. Technological innovations are particularly relevant to the mining industry, which deals with the challenges of depleting access to resources, requiring new solutions to remain sustainable and competitive. In the last decade, the mining industry has come to realise that technological innovations can directly contribute to its sustained competitive advantage (Sanchez, Hartlieb, 2020), helping to reduce costs, lessen environmental impact, increase production, and improve mineral recovery. While understanding barriers and drivers for technology adoption is important for the success of technology implementation efforts and the sustainability of the mining sector (Muduli et al., 2013), this paper suggests strategies to exit the dilemma, proposing a preliminary framework.

Oct 24, 2025

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By W. F. McKechnie

"Southern Africa is generally thought to be well explored, with only limited potential for major new diamond discoveries. However, Chiadzwa in Zimbabwe and reports of a significant new kimberlite find in Angola are testimony to the dangers attached to an attitude that ‘there is nothing left to find’.Since the major discoveries in the central interior of South Africa in the 1870s, diamond exploration in the region has been led by market and political factors that influence the key exploration drivers of opportunity and value proposition. Unexpected new discoveries by new players always impact on existing producers and, from time to time, denial of opportunity through political or protectionist policies has inhibited investment in exploration.Entrepreneurial exploration appetite in southern Africa will be tempered by the potential value equation and security of investment. Overlaid on this, developments in diamond recovery technologies provide opportunity to reinvigorate current mines and old prospects previously considered too difficult or costly to exploit. Position on the cost curve will remain a key factor for survival in an increasingly competitive environment. IntroductionThe diamond industry in southern Africa boasts a history of 150 years of discovery and mining, forming the cornerstone of development of the core, modern economies at the southern tip of Africa.Since the discovery, in the 1860s and 1870s, of the secondary diamond placers and primary diamond-bearing kimberlite deposits in the central interior of the then Cape Colony and Orange Free State, southern Africa has endured as the pre-eminent diamondproducing region in the world. Notwithstanding periodic competition from significant new discoveries in other parts of the globe and the paucity of recent, new discoveries in the region, its ranking is unlikely to change in the short to medium term.In a geological context the region contains the Kaapvaal-Zimbabwe and Angola-Kasai cratons, identified in terms of Clifford’s rule as areas inherently prospective for diamonds, being underlain by portions of the Earth’s crust that are tectonically stable and older than 1.5 billion years (Clifford, 1992). Although the Democratic Republic of Congo (DRC) would, in a geographic context, be considered to be part of Central Africa, for the purposes of this review it is included in southern Africa since northeast Angola and the adjacent parts of the DRC form part of the same geological terrane and diamond production from both countries needs to be considered together. Historical and current diamond production from the northeastern parts of the DRC around Kisangani is not considered to be significant and its inclusion in the overall numbers for the DRC does not materially affect the overall picture presented here."

Feb 1, 2019

By L. Godfrey, Z. Nontso, F. Magweregwede, B. Maphalala, S. Khan

The aim of this paper was to establish if mineral resource scarcity is a driver for South Africa to transition to a circular economy. The project objectives were achieved by investigating economically viable, and critical or strategic minerals remaining in South Africa, as well as resource scarcity, as a driver for South Africa to transition to a circular economy. The study found that some minerals in South Africa, such as iron ore, lead, manganese, gold, and cobalt have less than 50 years of economically viable mining remaining. At least 18 minerals can be classified indicatively as critical or strategic: aggregates, bauxite, chromite, cobalt, copper, gold, graphite, iron, limestone, lithium, manganese, nickel, phosphorous, platinum group metals, rare earth elements, silver, titanium, and vanadium. The classification was based on the minerals’ economic importance, supply risk, and potential use in the development and manufacturing of emerging technologies. The findings suggest that the scarcity of mineral resources is a critical driver for the country to transition to a circular economy. Other identified drivers include socio-economic factors, climate change commitments, and business objectives. All minerals are non-renewable resources and at risk of depletion, therefore sustainable extraction and use are critical. Priority should be directed at investigating circular economy opportunities and substitutes for commodities at risk of being depleted within the next 50 years. There is an opportunity for South Africa to transition from a minerals export-based model to one that promotes local mineral beneficiation and manufacturing of end products.

Mar 5, 2025

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020