Search Documents

By W. K. Loftus, H. S. Simpson

Discussion I. R. M. Cheston (Visitor): I should like to congratulate the authors on this interesting paper which graphically illustrates the overall effects of the gradual developments in diamond concentrating processes which have taken place over the past few years. These final stages of diamond concentration represent only a minor factor in the cost of diamond production but because of the shortage of highly trained people for this work, any easing of the burden on the sorting staff has an importance far beyond the immediate economic sphere. The search for the solution of problems posed by the economic and social conditions of industry is never-ending. The Diamond Research Laboratory is, even now, carrying out further work to improve still more the operation of general diamond recovery processes as described in the paper. Before looking at some of the latest developments in this field of final recovery, there are a few points arising from the paper on which I would like to comment. On page 321, reference is made to the X-ray sorters originally developed by the DRL. The paper gives a figure of 100 per cent recovery of diamonds from +7 mesh concentrates in two passes through the prototype machine. Not wishing to claim miraculous powers for our group, I would prefer to see this given as virtually 100 per cent recovery of all fluorescing diamonds. Firstly however much care is taken, there is bound to be an occasional operating loss. In the test work, 100 per cent recovery was made on many occasions but this was not always so. Secondly, although most diamonds fluoresce strongly under X-rays, some diamonds only fluoresce weakly. Type IIB diamonds, in fact hardly fluoresce at all, but the incidence of this special type of diamond is very low in most deposits. However, in operating the commercial X-ray machines, there is a certain background level of reflected radiation from other feed particles. Unless the diamond fluorescence is several times greater than this, it is not possible to achieve sufficient sensitivity in ejection. A certain small but variable proportion of diamonds from each deposit is always found to fluoresce too weakly to be recovered by the X-ray machine. Tests have shown, that for the De Beers mines, this proportion is considerably less than I per cent. These diamonds are nearly all dark brown or black in colour and therefore of low value. The degree of fluorescence does not, however, depend entirely on the colour or quality of the diamond and some of the brightest fluorescence comes from the lowest quality of boart diamonds. Investigations into the property of the diamond which causes this low fluorescence are being carried out. On page 322 it is suggested that zircon fluoresces in the same colour spectrum as the diamond. This is not quite accurate. The total light given out by zircon under X-rays is of the same order as that of diamond. However the zircon radiation has a much wider spectrum band than the diamond fluorescence. Reference is also made on page 322 to the effect of selective milling in small laboratory mills on diamonds. Perfect diamonds are very hard and very strong and are extremely difficult to break. Imperfect diamonds, which form the majority of diamonds recovered from most deposits, although hard, can be very brittle. Even under slight impact some of these diamonds may shatter to powder. Milling conditions must therefore be extremely closely controlled to minimize breakage, and even so, some breakage will always occur. As suggested in the paper, the necessary conditions are: the use of small balls, slow speed mills and very limited water addition. Tests elsewhere have suggested that the water content of the pulp in such a mill must be less than 25 per cent by weight of pulp to prevent diamond breakage reaching significant proportions. The skin flotation techniques described on page 323 operate on a very small scale. It is of interest to note that in West Africa a large-scale continuous skin flotation machine is used to recover the fine diamonds. In this operation the feed is dried and, after standing, is mixed with water and fed in a single layer onto a woven phosphor-bronze conveyor belt. This belt runs at a shallow angle into a water bath and as the particles are carried through the air-water-interface, the diamonds float off and over a weir into a collecting box. The bulk of the particles, being wettable, sink to the bottom of the tank and are continuously removed. If treated without prior drying, the diamond recovery is poor. If material is treated immediately after drying, a lot of the gangue particles also float. During standing, in the hot and humid atmosphere of West Africa, it is found that the gangue particles recover their wettability much faster than the diamond particles. Optimum selectivity is obtained after standing for approximately 24 hours. At the DRL we have been experimenting with optical filters to differentiate between the fluorescence of diamonds and zircon. By limiting the light transmission to the fairly narrow range emitted by diamonds, it is

Jan 4, 1970

By P. Lloyd

Perceptions of disaster caused by burning fossil fuels have reached such a pitch that they seriously threaten the very future of the industry. Coal is a dirty word. A leader in Business Day(January 192009) claimed ?There is no disputing that renewable and non-polluting energy sources are preferable to the country?the true cost of so-called cheap coal-fired power stations is neither reflected nor accounted for by Eskom?the true and immediate but unacknowledged cost of continued coal mining is apparent in the catastrophic level of acidification from mining runoff of all significant natural water resources in the country?and their waters have been rendered unfit for human consumption. Air quality is in a similar state with?increases in pulmonary disease causing workforce absenteeism and compromised childhood development, among many other health problems recorded in areas polluted by coal mining.? The upshot is that our latest coal-fired power station, Kusile, is being required to use flue gas desulphurization. The costs are considerable, and the benefits minimal. Meanwhile, exports are being threatened by EU directives and an assumption that South African coal gives off excessive quantities of SOx and NOx when burned. The industry needs to arm itself with clear responses to these and similar misconceptions, and to communicate those responses loudly and clearly, if it is to survive.

Jan 1, 2011

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023

Statistical summary of the mineral industry world production, exports and imports 1964-1969 Published by Her Majesty's Stationery Office, London, on behalf of the Institute of Geological Sciences (1971) The Statistical Summary contains a wealth of care fully garnered information on the production, exports and imports of the principal minerals and mineral products throughout the world for the period 1964-1969, and it should therefore be of particular interest to economic geologists and others concerned with marketing and selling minerals. In view of the intractable nature of the source data it is quite an achievement to have published figures for 1969 so expeditiously. On picking up the Summary this reviewer instinctively compared it with the Annual Yearbook published by the United States Department of the Interior. The Yearbooks have been issued annually since 1882, and today each consists of a set of three separate books containing five volumes. Apart from abundant statistics on the domestic and international mineral industries, the Yearbooks are known for their perspicacious reviews and articles on a host of different facets of the world's minerals industry. Physically the Summary is a much slimmer publication than the Yearbook, and it contains no commentary whatsoever other than occasional footnotes. The principal contents are a series of tables showing production, exports and imports of fifty-nine of the world's more important minerals and mineral products. Each table shows the weight of the material produced or traded, by countries, with figures for each of the six years in adjoining columns. In some cases (e.g. diamonds) values in British currency are quoted in addition to weights. Most of the data have been abstracted from national reports and returns, although in some instances estimates are quoted where national sources are silent--as for example the production of platinum in South Africa. One wonders in passing if any useful purpose is served by the continued suppression of this particular figure. The four South African producers must surely be able to estimate each other's production fairly accurately by now, and one imagines that the national export figures can likewise be synthesised. This reviewer has two minor criticisms of an otherwise praiseworthy publication. Firstly it seems an unnecessary anachronism to perpetuate the split between 'Commonwealth' and 'Other' countries-the split can have little practical significance today. Secondly, what is one to make of the statement that the 1966-1969 figures for exports from Rhodesia of chrome ore and copper, to take two examples only, are 'not available'? It seems improbable that no estimates of these figures have been made since the imposition of sanctions, and inevitably one suspects that the figures have been excluded on policy grounds. Hopefully this problem will have been solved when the next Summary is published. M.J.M. South Africa, land of Challenge by Maurice Tyack France Interpresse, 323 pages, price R18-00. Is South Africa God's richest acre? In its mineral wealth it certainly is, but what of the many other complex overlays of emotions, traditions and racial problems? South Africa, Land of Challenge, provides the background. This is reported to be the first comprehensive documentary work of its kind on South Africa. It is a handsome volume measuring 12ft by 9f', is illustrated by at least 600 photographs of South Africa, more than half of which are in colour, and contains 21 original maps and charts. The book covers the full spectrum of South Africa's very existence, its geography, pre-history, its customs, countryside, natural resources and its cities. The more controversial categories are thoroughly discussed, the people, their policies and politics. Mr Tyack is eminently qualified to write on South Africa, being the author of over 20 books on other African countries and having spent more than three years of research, in the field, in South African archives and also in various libraries and museums, in preparation for this book. The book claims to be free of any party political bias and appears to be an honest attempt at a factual survey. However, a work of this magnitude will undoubtedly leave an impression on the reader and the tone of this book is decidedly patriotic. This is a useful reference work on South Africa that most South Africans will be proud to own. J.P.H. Ergonomics and physical environmental factors This publication by I.L.O. of a symposium in Rome in September 1968 has much useful information for the mining industry in regard to the health and productivity of its labour force. The first subject dealt with is mechanical vibrations. From this section it is clear that men who drive, for many hours each day, vehicles which vibrate in the 6 Hz range are subject to serious physiological and psychological effects. The former may show as changes to the vertebral column (which has a resonance in the 4-5 Hz range). The circulatory system is adversely effected by values in the 6-10 Hz range and the vision is impaired at between 40-100 Hz. Less definite knowledge exists of the effects of vibration on the hand-arm system from mechanical drills etc, although Raynauds disease of the blood vessels of the hand and degenerative diseases of the elbow and shoulder joints occur in men using drills which vibrate, respectively, in the higher and low frequency ranges. Industrial noise is extremely well dealt with and the latest knowledge is summarized. Clear information is given on the relationship between time of exposure to

By B. Hayen

The principal advantages of fibre optics as compared to copper wire are well known and include almost perfect electromagnetic isolation, light weight, small size, excellent transmission security and substantially better bandwidth/distance performance. The decreasing cost of the optical fibre technology (both fibre cable and equipment) has led to another generation of private networks, which provide much larger bandwidths, very high reliability and an increase of the maximum geographical coverage. The larger bandwidth allows to transport all types of information on a single network. Typical communication requirements are speech (audio), computer data, LAN info, control information, video, etc. OTN or ‘Open Transport Network’ is a transmission system based on the latest available technology in fibre optics. It is characterized by the dual ring approach, resulting in high network availability, and the integration of different types of services in one network. As such, it can fulfil almost all transmission requirements for voice, data, LAN, video and any special service required.

Sep 1, 2001

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

By John Freer

The time 06h30 in midwinter is a little early to set out on an excursion from Johannesburg. Yet this was the hour that members, many accompanied by their wives, started to assemble in the parking lot adjacent to the squash courts at the Wanderers Club, Illovo, for a visit to Premier Diamond Mine at Cullinan. All fifty were checked in and aboard the coach by 07hOO. Coffee and sandwiches, served en route by Doris Gardner and Pam Binstead, were most welcome. IMM awards Given below are details of the trust funds, etc., to which applications are invited for grants, etc., payable in 1985. Application forms, which must be returned to the Secretary before 15th March, 1985, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1984

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020

By K. C. Corin, M. S. Manono

The mining and mineral concentration of Cu-Ni-PGM sulfide ores in South Africa occurs in semiarid regions. The scarcity and availability of water resources in these regions has become one of the biggest challenges facing mineral concentrators.S Owing to this challenge, concentrators have to find ways through which they can manage and control their water usage. Recycling and re-use of process water in mineral concentrators has therefore become common practice. This practice is beneficial in that it reduces reliance on municipal water, harnesses compliance to stringent environmental regulations on water usage, and it also offers a better response to the Sustainable Development Goals. This could however be somewhat concerning to the operator as recirculated water often has higher concentrations of ions compared to fresh or potable water. The unintended change in the process water quality may potentially affect critical aspects of flotation such as the stability of the froth. This has led to the need to find those process water ions that have the greatest impact on froth stability. Thus, this paper investigates the effect of various ions common in process water of a typical Cu-Ni-PGM concentrator on froth stability. Bubble size, water recoveries, foam height, and dynamic froth stability in both twophase and three-phase flotation systems are used as proxies for froth stability. Findings of this study are deemed crucial towards the development of a process water management protocol in sulfidic Cu-Ni- PGM ore concentrators. Keywords: Bubble diameter, electrolytes, flotation, froth stability, water quality

Jan 1, 2020

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

SYNOPSIS The phase equilibria, viscosities and sulphur capacities of titaniferous slags were determined in the composition range of CaO = 30 to 0 per cent, MgO = 0 to 30 per cent, SiO2 = 19.69 per cent, AI.O. = 13.12 per cent and TiO2 = 37.19 per cent. The phase equilibria were determined by high temperature microscopy, the viscosities were measured using a rotating outer cylinder viscometer and the sulphur capacities were evaluated from the results obtained by equilibrating the slag in a gas stream of CO, CO2 and SO2. The behaviour of these titaniferous slags under reducing conditions was examined. Possible use of the slags for aggregate, or slag-cement, and the possibility of extracting the TiO2 are discussed. CONTENTS INTRODUCTION PHASE EQUILIBRIA VISCOSITIES DISCUSSION OF THE PHASE EQUILlBRIA AND THE VISCOSITY VALUES EFFECT OF REDUCING CONDITIONS SULPHUR CAPACITY DISCUSSION OF THE SULPHUR CAPACITY VALUES POSSIBLE USES CONCLUSIONS ACKNOWLEDGEMENTS REFERENCES INTRODUCTION The latest phase in the exploitation of the mineral wealth of the Bushveld Igneous Complex is the erection of a plant by the Highveld Steel and Vanadium Corporation Limited near Witbank to produce steel and vanadium-rich slag from the titaniferous magnetites occurring in this rock formation. These titaniferous magnetites occur as segregations in the gabbro body and the TiO2 is mainly present within the structure of other constituent minerals but also occurs in smaller amounts as ilmenite and ulvospinel. The vanadium is thought to be present in the iron oxide phase due to isomorphous replacement of the iron. Until very recently, it was feared that the high titania content of these titaniferous magnetites would militate against their value as useful iron ores. However, the design of an integrated plant to produce both steel and vanadium-rich slag, and in which the iron-making process is conducted in submerged arc furnaces instead of in

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

By D. F. Malan, R. P. Els

The limit equilibrium model, used in displacement discontinuity codes, is a popular method to simulate pillar failure. This paper investigates the use of physical modelling to calibrate this model. For the experiments, an artificial pillar material was prepared and cubes were poured using the standard 100 mm × 100 mm civil engineering concrete moulds. The friction angle between the cubes and the platens of the testing machine was varied by using soap and sandpaper. Different modes of failure were observed depending on the friction angle. Of interest is that significant loadshedding was recorded for some specimens which visually remained mostly intact. This highlights the difficulty of classifying pillars as failed or intact in underground stopes where spalling is observed. The laboratory models enabled a more precise calibration of the limit equilibrium model compared to previous attempts. Guidelines to assist with calibration of the model are given in the paper. The limit equilibrium model appears to be a useful approximation of the pillar failure as it could simulate the stress-strain behaviour of the laboratory models.

May 3, 2023

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025