Search Documents

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By Earl T. Hayes

THIS BIBLIOGRAPHY has been assembled to aid research by the Bureau of Mines, and others on high-purity tungsten. It appears approximately 50 years after the development of ductile tungsten-one of the first metals to be produced in a high-purity form. Requirements of the missile age are ever more demanding that engines rout hotter and space vehicles fly higher and faster. Thus, it has become necessary to reexamine all conventional materials of construction as well as to investigate new combinations. At this stage of our technology we have alloys capable of operation at 1,800° F. and several possibilities of developing some. that will be satisfactory up to 2,500° F. Strength-weight comparisons, detrimental to tungsten at, lower temperatures, disappear at this point, mid tungsten or its alloys appear to be the only metal capable of operation at truly high temperatures. The aim of this bibliography has been to include only references that concern improving the purity of tungsten-from processing the ore to treating the finished metal. In this sense it is a selected and not a critical bibliography. The period front January 1911 through February 1959 has been covered. Because repent literature has the greatest, value, most of the selected items refer to publications issued within the pest 5 years.

Jan 1, 1960

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

A compilation of papers presented at the Fourth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 2-4, 1978. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1978

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By G. M. Kintz, Charles B. Carpenter, G. W. Jones

"INTRODUCTION At 9:12 a. m. on April 16, 1947, the ammonium nitrate cargo in hold 4 of the S. S. Grandcamp, a 7,176 gross-ton Liberty ship owned by the French Government, detonated at pier 0 of the Texas City Terminal Railway Co., Texas City, Galveston County, Tex.This detonation was the first of a series of explosions and fires that took the lives of approximately 600 persons, injured 3,000 other persons, and caused a property damage and business loss that will exceed $58,800,000. It has been estimated that the life, accident, and workmen's compensation insurance loss will be $8,200,000.At 1:10 a. m. on April 17, 1947, the ammonium nitrate cargo in hold 5 of the S.S. High Flyer, a 6,214-gross-ton Liberty ship owned and operated by the Lykes Bros. Steamship Co., Inc., detonated at pier L. This explosion materially increased the property damage caused by the first explosion, in between 50 and 100 persons, and is believed to have taken the life of only one person.The exact number of casualties resulting from the Texas City disaster may never be known. On June 22, 1947, 65 days after the explosions, the red Cross and the Texas Department of Public safety repoted:,""Identified dead, 405; unidentified dead, 63; believed missing, 100; injured, 3,000; hospital¬ized, 600; still in hospitals, 37."""

Feb 1, 1948

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

The London Metal Exchange began its first official session of aluminum trading on Monday, October 2, LME prices based on 3-month forward contracts opened Monday at 52.4 cents per pound, fell midway through the week to 52.3 cents and ended Friday at a high of 52.7 cents. For the week, LME metal averaged 52.5 cents. Although Reynolds Metals Co. and Aluminum Co. of American continued in September to value unalloyed 99.5 percent aluminum ingot at 53 cents per pound, other producers were at higher positions of 55-57 cents. Alcan Aluminum Corp. of Alcan Aluminum, Ltd., a Canadian producer, increased prices for its U.S.-marketed ingot by 2 cents to 55 cents per pound, effective September 21. New York merchants increased ingot quotes by approximately 0.5 cents to 52.8-53.5 cents per pound.

Jan 1, 1978

Norton Co., a manufacturer of abrasive products and diamond drilling and coring bits for oil and gas exploration, is building a $19.1 million addition, scheduled for completion in late 1980, to the Huntsville, AL. The plant makes alumina-zirconia abrasive grains used in grinding wheels and coated abrasives. ALUMINUM Martin Marietta Aluminum Inc. announced plans to expand production capacity of its 112,000-ton-per-year primary aluminum smelter at Goldendale, WA to 177,000 tons per year. The $125 million expansion was scheduled to come onstream in 1981. The Aluminum Company of America announced plans to restart a fourth potline during October at its 185,000-ton-per-year Point Comfort, TX primary aluminum smelter.

Jan 1, 1979

By J. H. Jacobs

This report records a chapter in the history of the development of an electrolytic manganese industry in the United States. Nearly all the manganese requirements of the United States have been imported. Although there are large quantities of manganese ore in the United States, most of it is low-grade and cannot be used for the production of ferromanganese. Since the electrolytic production of manganese carried out by a process developed in the laboratories of the Bureau of Mines offers a method whereby the extensive low-grade deposits may be utilized and since commercial development had proceeded slowly, the Bureau constructed a new and larger pilot plant at Boulder City, Nev., where abundant electric power was available. An authorization in November 1940 covered a plant of only several hundred pounds daily capacity. Additions to some sections author¬ized by subsequent appropriations have enabled the plant to produce over 2,000 pounds a day for extended periods.

Jan 1, 1946

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By J. N. Geyer

During the early stages of the mining industry of the United States an apparently inexhaustible supply of high-quality, easily accessible coal made the product cheap and the attendant mining methods wasteful of recoverable coal. Because coal from advance places could be mined with less effort and a large outwit obtained as the entries advanced, much of the coal left in pillars to support the roof was lost. Squeezes often developed in these mined-over areas, or, if pillars were of sufficient size to-prevent squeeze, the roof would be so weakened by long exposure that any pillar recovery was extremely hazardous. As the value of unmined coal increased, a high recovery of the available coal became necessary. Numerous plans were tried during the period that followed, some of the methods proving successful while others were complete failures or only partly successful. As a better knowledge was pained of the roof strata and its behavior, however, pillar mining became more successful and methods suited to special roof conditions were developed.

Jan 1, 1933