Search Documents

By Cathy Aimone-Martin, Caitlin Woznick, Brent Meins

This study is a continuation of previous work in which the responses of tall structures to close-in construction blasting at two rock excavation sites are evaluated. A total of eight buildings were instrumented to calculate blast-induced wall strains. Of these structures, five high-rise buildings measuring 166 ft (51 m) to 294 ft (90 m) in height (15 to 24 stories), were included for this study and compared with the results of previous studies that included one to three story residential structures and mid-rise structures (four to six stories). All five structures were built between 1908 and 1940 with interior walls comprising aged plaster. Three of the structures are designated Landmark, subject to a 0.5 in/s (12.7 mm/s) regulated peak particle velocity (PPV) limit. The regulated PPV limit for the two other structures was 2.0 in/s (50.8 mm/s). To date, a total of 450 close-in construction blasts have taken place over six months at the two adjacent projects, blasting three to six times per day at each site. Seismograph instrumentation included tri-axial geophones in the ground and bi-axial geophones (horizontal components only) mounted on structure exteriors at the corners closest to blasting. Peak global wall tensile strains were calculated from time-correlated differential structure displacements in two horizontal directions as measured by upper and lower geophones mounted near the roof and at street levels. Wall strains were correlated with ground excitations to establish a stiffness factor for each structure defined as the upper bound linear regression slope for strain as a function of ground displacement. In addition, a structure-specific regression best-fit function was established to relate horizontal components of displacement to velocity. These two functions were used to determine the maximum ground motion velocity for a desired limit placed on wall strain. A 25 ?-strain limit was suggested for both projects to protect interior plaster walls. To date, global wall strains have not exceeded 0.53 ?-strains (or 47 times the project limit) for peak particle velocities up to 3.49 in/s (88.6 mm/s). This demonstrates the low strain response of tall structures to ground velocities well above regulated limits. The stiffness factor computed for the most flexible high-rise building was 688 in-1 (17475 mm-1). In comparison, stiffness factors for the most flexible residential and mid-rise structures previously studied were 8651 in-1 (219735 mm-1) and 4387 in-1 (111430 mm-1), respectively. Based on a large number of measurements made at these study structures, the maximum horizontal ground velocity needed to achieve 25 ?-strains in walls ranged from 36 in/s (914 mm/s) to 192 in/s (4877 mm/s) because of the high stiffness of these buildings. Such high amplitudes of ground vibrations can never be safely achieved during close-in blasting in urban environments. These excessive values stand to show how unfounded the current limits of 0.5 in/s (12.7 mm/s) and 2.0 in/s (50.8 mm/s) are when applied to massive, tall structures. This study demonstrated that upper structure motions are highly attenuated from the lower (street-level) motions because of the long travel distances up the buildings. High-rise structures are far stiffer than mid-rise and residential structures and can withstand ground vibration amplitudes far greater than the currently enforced blasting limits in New York City.

Jan 1, 2015

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997

By Don W. Lake

Of all the blast monitor& instrumentation systems and techniques av&able today, highspeed photography and videography remain as the most valuable, stand alone, diagnostic techniques to evaluate full scale blasts in the mining and explosives industries. Highspeed image data, coupled with information from other instrumentation systems, such as continuous VOD records, seismographs, laser surveying systems, refraction seismographs, etc. can eIiminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both good and bad blasts is increased, and optimum blast designs are achieved considerably faster when compared to the trial and error approach or relying on just the experience factor.

Jan 1, 1992

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By Italo Onederra, Jason Furtney, Ewan Sellers

The detonation reactions occurring during rock blasting result in high pressure gas phase products from the condensed explosives typically used in mining applications. After detonation and the initial fracturing, the work done by the expansion of this gas contributes to burden movement and further rock fracturing. Before all of the energy in the reaction product can do useful work on the rock, some of this energy is lost to crushing and possibly to gas venting to the atmosphere. Borehole gas pressure decreases by three principle mechanisms: (i) expansion of the borehole cavity, (ii) flow into the fracture network, and (iii) flow through the stemming. To simplify the problem and to get a better understanding of the interaction of these mechanisms, a simple model for each of these mechanisms is developed. A comparison is made of the time-scales and the influence on burden movement for each. A comparison of gas flow behavior is made between typical ANFO and emulsion products.

Jan 1, 2012

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

By Tom Short

"Construction blasting covers a very extensive variety of explosive applications. I will discussseveral of these with you and then show slides from my collection, starting in 1956, which will betterillustrate the types of blasting under discussion."

Jan 1, 1991

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By Richard R. Brochu

At the International Society ofExplosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this wmmittee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give ‘results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same ,&thin stated tolerances.

Jan 1, 1998

By Jeffrey L. Dean

Now in its twenty-fifth year, the ISEE has grown to more than 4000 members representing 75 countries. The Society and its 35 chapters in the US, Canada and Australia work to educate the public about our industry, provide forums for the exchange of explosives technology, serve as a repository of explosives information, offer expert help to governments, develop standardized methods and terminology, and promote research and education by, creating and conducting certificate and trainktg programs and encouraging the teaching of the safe and controlled use of commercial explosives.

Jan 1, 1998

By David Reddick

The mining industry is in the midst of dramatic change. Mining activities are moving from industrialized first world countries (Canada, Australia, and the United States) to the third world. This shift is occurring due to depleted reserves, tough environmental standards, and expensive labor in traditional mining countries. During a recent trip to South Africa, I was asked, owing to my educational background in economics and an international involvement in drilling and blasting, what changes could be anticipated in third world blasting practices as labor costs increase. It is from that beginning that this presentation has evolved.

Jan 1, 1997

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By Stephen H. Chung, Kevin Atherton

The main purpose behind this preliminary study was the reduction of costs while maintaining productivity. Finding a way to achieve this balance without compromising controls on safety and quality of blasting results is of continual interest to the mining industry and of particular interest when ore of lower grade is being mined.

Jan 1, 1998

By John Watson, Jay Rodgers

The world of blasting and explosive use continues to evolve into one which relies heavily on measurement, quantification, process control, and information feedback as a means of contributing to operational improvements. More than ever good blast performance, once thought to be a result of someone’s “artistic ability”, is giving way to “hard science” and measurement techniques. Variability in product performance and process control is becoming less tolerable with increasing environmental issues, regulatory pressure and public awareness.

Jan 1, 1998

By Larry: McAnuff Schneider, Edward Walter, Gordon Shaw, Daniel Grieco, Dennis Clark

During the 1998 Annual Conference of the International Society of Explosives Engineers (ISEE), the Seismograph Section established a subcommittee for the purpose of compiling a list of all regulations pertaining to limits imposed on ground vibration generated by blasting. The goal of this project was to determine the vibration regulatory levels being enforced, with the further intention of examining their scope, and uniformity. A secondary purpose was to evaluate the consistency of the existing regulations with the current scientific findings on structural response and damage potential.

Jan 1, 2001

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By Robert Hopler

That some time in the year 1872 there was organized an association composed of practically all of the manufacturers of gunpowder and other high explosives in the United States, the members of which said association were as follows: E. I. du Pont de Nemours & Co., The Hazard Powder Company, Laflin & Rand Powder Company, Oriental Powder Mills, American Powder Company, The Miami Powder Company, and Austin Powder Company of Cleveland, all of which or their successors are defendants herein; that the object and purpose of said association was the elimination of all competition between the members thereof in the shipment and sale of gunpowder and other high explosives among the various States and Territories of the United States; that the only manufacturers of gunpowder and other high explosives which did not join such association at the time of its organization were the California Powder Works, The Sycamore Manufacturing Company, and The Lake Superior Powder Company, but your petitioner alleges that each of said three last named companies

Jan 1, 2008

By Dale S. Preece, Stephen H. Chung

Electronic detonators and the attendant precise detonation timing that they facilitate are having a measurable effect on rock blasting in terms of improved fragmentation and vibration control. These improvements are increasingly well documented which is driving the expanding use of electronic detonators. In spite of the growing body of positive evidence concerning the benefits of precise delay timing, very little work has been done to document the impact of electronic detonators on the movement of rock. In this study 3-D computer programs, used to predict blasting induced rock heave, including the effects of detonation timing, are used to simulate the effect of precise timing on rock movement. Implementation includes quick, precise timing between blastholes going down a row and then much longer delays between rows of blastholes. For example an effective blast design might call for precise 3 ms delays between blastholes along a row and then 60 or 72 ms between rows. Several options are studied in this paper using computer simulations to draw some conclusions about the underlying physics affecting the process and how precise timing might have a positive impact on blasting induced rock motion.

Jan 1, 2005

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994