Search Documents

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984

By J. D. G. Groom

The introduction to a selection of papers from the Minerals '98 professionals' conference, held in London, 24 June 1998 as part of a week of activities supported by 13 professional and trade associations to promote the industry, highlights enthusiastic visitor comments on quarry visits around the UK and outlines the Foresight programme whose key issues were addressed at the conference

Jun 21, 1905

By Ruddle R. W.

An outline account is given of the smelting of copper and the chemistry of the process. A table provides compositions of the more important minerals from which copper is won by smelting. Roasting is discussed as is smelting using reverberatory furnaces, blast furnaces and flash smelting. A brief discussion of converting covers the upright (Great Falls) converter and the horizontal (Peirce-Smith) converter.

Jan 1, 1953

By S A. M Crawshaw, J A. B Fortune

Trackless battery powered haulage vehicles have been in operation in British coal mines principally for longwall face transfer and personnel transportation. Changes within the industry have resulted in the introduction of room and pillar coal mining methods and the introduction of increasingly heavier longwall roof supports This has resulted in the introduction of: • Battery powered coal haulage machines, which, without the need for trailing cables, increase productivity within room and pillar mining. • Battery powered longwall shield haulers which are capable of carry ing the heaviest shield supports currently being utilised within the British coal mining industry. The conventional machines have been adapted from an American design to meet the requirem ents of European legalisation. This has seen the- emphasis being placed upon the supplier with the European M achinery Directive being introduced, necessitating the assigning of a 'C E ' m ark to each vehicle. Battery vehicle technology has advanced to meet the demands of the ever changing market and will no doubt he further adapted to meet the requirement of the British coal mining industry.

Jan 10, 1996

By C. H. J. Beaven, M. P. Jones

Since the various new techniques of automation and computing have enabled vast numbers of mineralogical observations of relatively small samples to be made cheaply and rapidly, the statistical assessment of these measurements has become of vital importance. Much of the theory and most of the procedures of sampling that are used in the mineral industry are based on Gaussian statistics, but modern measuring techniques show that many mineralogical parameters do not necessarily follow the Gaussian distribution function. Consequently, it has become necessary to examine the application of other, more suitable statistical methods in order to derive the maximum amount of useful information from the examination of mineralogical samples. Some of the errors that can be introduced by the use of incorrect distribution functions are discussed and the value of determining the function that is appropriate to the particular parameter that is being measured is shown. Examples are provided of non-Gaussian distribution functions in mineralogical materials that were encountered during prospecting and during mineral treatment operations: a Canadian uranium ore, a Thai tin ore, and gold ore tailings.

Dec 1, 1971

By J. Laskowski, J. Lekki

"The mechanism of joint action of a frother (alpha-terpineol) and a collector (ethyl xanthate) in the flotation of chalcocite has been examined. In order to study the dynamic effects of frother and collector in bubble-particle collisions, the following aspects were investigated : determination of zeta-potential. Measurements of the thickness of fluid film on the surface of chalcocite and adsorption of xanthate, as influenced by alpha-terpineol, induction time and flotation versus concentration of alpha-terpineol and ethyl xanthate.The mechanism of the adsorption-desorption phenomenon on chalcocite with regard to non-ionic molecules, e.g. a-terpineol, has been considered, and the influence of this on the stage and thickness of the intervening wet layer between a bubble and a particle, changing the probability of collision and attachment, is suggested."

Dec 1, 1971

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By M. W. Davies, P. N. Smith

The activity of MnO has been measured in the system CaF2-MnO at 1773 and 1873 K and in the system CaF2-CaO-MnO at 1773 K by the method of equilibration with platinum. Large positive deviations from ideal solution laws have been found, but these became less as the lime content rose. The loss of a volatile component made activity measurements impossible in the CaF2-AI203-MnO system, but the boundaries of a two-liquid region have been measured at 1773 K.

Dec 1, 1971

By P Shead, M A. Tuck

Both climate and methane control have been a prime concern in the development of the workings within the Deep Soft seam at Harworth Colliery. This paper describes the numerous methods employed over the past 15 years to effect control over these two major environmental pollutants at Harworth and describes a future method of working which will enable the output levels required to be achieved, whilst effecting the required level of both climatic and methane control. Firstly, the paper gives a broad historical overview of the steps taken since 1981, when production started in the Deep Soft seam at Harworth Colliery, to effect control over the main environmental pollutants in the seam. Secondly, the paper details the results of planning exercises undertaken to assess the various options with respect to panel layout, to achieve environmental control in future production districts. Finally, the recommended method of panel design to achieve the levels of production required is detailed.

Jan 7, 1997

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By J. E. Rouse, D. L. Buchanan

"During the emplacement of the Bushveld Complex in the Potgietersrus area magma reacted with the original floor rocks— Archaean granite or Malmani dolomite and overlying Penge handed ironstone or sedimentary rocks of the Pretoria Series. The complex sequence of sulphide-rich mafic rocks that formed along the contact is known as the Platreef. Associated with the sul­ phide mineralization are important concentrations of platinum-group metals, copper and nickel. Xenoliths of Malmani dolo­ mite have been incorporated into the Platreef and previous work has suggested that anhydrite is likely to have been present in the dolomite. The sedimentarv-derived sulphur thus introduced into the magma exercised an important control on the forma­ tion of the sulphides.Petrographic studies on the Platreef rocks from the Tweefontein area indicate that the original magma reacted with the banded ironstone to form iron-rich pyroxenites. In the Turfspruit area, to the south, the footwall rocks consist of sediments of the Timeball Hill Series. Original argillaceous rocks have been metamorphosed to cordierite-, corundum- and spinel-bearing hornfelses. Graphite was present in the contact zone in both the Tweefontein and Turfspruit areas. Anhydrite-bearing hornfels rocks are also present on Turfspruit.The Platreef rocks that overlie the corundum- and spinel-bearing hornfelses on Turfspruit are peridotitie, and pyroxenites are present in areas underlain by cordierite-bearing hornfels. The absence of orthopyroxene in the peridotite is probably indicative of low silica activity in the original magma. The pyroxenites have, however, undergone silica contamination from the underlying more siliceous cordierite hornfels.Carbon isotope studies indicate that the graphite in the Tweefontein and Turfspruit samples represents organic material orig­ inally associated with the footwall sediments. Sulphur isotope determinations on the anhydrite-bearing floor rocks indicate that this phase is clearly of sedimentary origin and was probably derived from an evaporitic unit within the carbonate sequence. This provides firm support for a model of ore genesis that involved the introduction of additional sulphur into the Bushveld magma. Isotope studies on sulphides associated with the banded ironstone and graphite indicate that these units were not the source of additional sulphur. Experimental studies predict, however, that a magma contaminated with iron- and carbon-rich material would have a high sulphur-carrying capacity. Where additional sulphur is available the magma would achieve saturation early in its crystallization history and precipitate an immiscible sulphide phase. Experimental work has also shown that sulphide precipi­ tation can be triggered by the introduction of salic material into a magma close to sulphur saturation. This mechanism probably played a role in the control of the sulphide mineralization in the Turfspruit area."

Jan 1, 1984

By G. J. Lyman

Mayer curves are used for process calculation in coal preparation. They can also be used to smooth washability data by fitting a hyperbola of particular properties to ash and yield, but to introduce the density variable an independent relationship with ash content must be adopted. When this ash-density relationship has a realistic form at low density, the implied form of the mass distribution function is unrealistic, suggesting that Mayer curves represented by a hyperbolic functional form are unsuited to coal washery calculations for low-density separations. Their use at higher densities is also uncertain. A similar conclusion can be anticipated when Mayer curves are used for other mineral systems.

Jan 8, 1992

By R. M. Honey

An attempt is made to summarise the mining law of England, Wales and Scotland. Attention is also drawn to the recent privatisation of the electric power and gas industries and the intention of the present Government to follow suit as regards coal mining. The subject of mining law is discussed under the headings: minerals or rights that have been nationalised or are vested in the Crown; ownership (of land and mineral rights); special customs; tracing of owners; right of support (arising from mining); ancillary rights and easements; obtaining prospecting and mining rights; planning permission; statutory aids to obtaining rights; notes on the history, law and practices of petroleum (onshore and offshore), gas, coal, prescribed substances, gold and silver; electricity; safety, health and welfare; and technical information and boreholes. A correction in the subsequent issue amends errors on p.A75 and A82 and regrets the publication of misinformation on the availability of grants

May 1, 1991

By Emanuel Shinwell, Douglas Hay

"Opening statements relating to the health and welfare of underground workers and the nature and prevention of silicosis and pneumokoniosis. During 1945-47, 10,500 UK coal-miners were certified by the Silicosis Medical Board to be suffering from pneumokoniosis and suspended from work in the industry. Over 80% of cases occurred in the South Wales coalfields. Silicosis and pneumokoniosis also occur among metalliferous miners, such as the tin-miners of Cornwall. The slate-quarries of North Wales are also troubled by these conditions as are the haematite mines of the North-West of England."

Jan 1, 1947

By Winmill T. F.

Paper presented at the at the Institution of Mining Engineers' general meeting held in London on 8th June 1916: In a previous paper it has been shown that the rate of absorption of oxygen by coal is neither directly proportional to the surface area of the coal exposed nor to the percentage of oxygen in the air. Further experiments are now described supporting this conclusion

Dec 1, 1916

The first part describes a model (the C model) based on the motion of the grinding charge. The charge is treated as a continuum, which allows analytical solutions to the equations that are developed. The C model is equally applicable to ball-, semi-autogenous and autogenous mills and contains a description of the power draw of both the cylindrical section and the cone-ends. Differences between the power draw of grate- and overflow-discharge mills are described from consideration of the different shapes and compositions of their charges. A large database of industrial mill data is used to demonstrate the accuracy of the model. Part 2 describes a simpler, empirical model (the E model) whose performance is based on that of the C model. The same database was used to assess the predictive capabilities of the E model. The model was shown to be only slightly less accurate than the C model despite its much simpler structure

Jun 18, 1905