Search Documents

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By A. Mainza, I. Govender, J. Waters

"The study of the properties of mineral processing suspensions is important in understanding how a circuit might behave. As soon as the predominantly dry ore enters a wet milling stage the ore properties undergo changes as a ‘slurry’ is created. Slurries can be classified in terms of their physical properties (particle density, solids concentration, particle size and size distribution, particle shape), and their flow properties such as rheology. Slurry flow regimes are classified into true homogeneous, pseudo homogeneous, heterogeneous and fully segregated, and only true homogeneous and pseudo homogeneous suspensions can be characterized by their flow structure. A class of the heterogeneous regime are the so-called dense phase or settling slurries - those which result in a clear water surface on standing, although they may approach a pseudo homogeneous state if suspended for a sufficient period of time. They are usually extremely difficult to characterize by their rheological properties alone and the rheological characterization of these slurries has always posed a problem, especially at higher concentrations. Previous rheological studies have focused on the individual concentrator units dealing with milling, classification, pumping, flotation, fine grinding, thickening.In this work an attempt was made to characterize two ore types (copper and a Platreef platinum ore) using a custom built Paterson and Cooke tube rheometer, at concentrations up to 43% by volume. After applying a turbulence correction, results showed Bingham plastic behavior. A conventional vane rheometer was then used to compare the rheological behavior of platinum concentrator streams. A size criteria was used to identify any rheologically dominant streams."

Jan 1, 2014

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By Heiko Schiemann, Christoph Beyer, Thomas Pretz

"Due to multiple experiences in the field of planning and engineering of processing plants for secondary materials the Chair for Processing and Recycling of Solid Waste Materials decided to develop a software tool that supports the engineering and the planning of the basic layout of processing plants for secondary material flows. The detailed description of the material flow and its characteristic parameters is one of the main tasks to be worked out and should be considered as the basis for representative simulation results.The description of the material flow and its characteristic parameters is based on a fraction vector containing 12 material fractions. This is a compromise between a detailed material flow description and a compact and therefore time-extensive calculation model. Each material fraction is characterized by 15 parameters, which can be edited with the help of an easily accessible user-interface. In addition to basic parameters like ignition loss, water content and calorific value more parameters like the material fraction-specific particle-size distribution are contained. Using the model library SimuRec, the processing success and the recovery of complex processing plants for secondary materials can be predicted."

Jan 1, 2003

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

The Separation in Froth (SIF) technique is based on the idea that the pulp is fed directly onto the froth layer prepared on the surface of liquid medium providing an effective method for separation of coarse particles up to a few millimeters size. Thus the SIF process can result in substantial savings in grinding energy and flotation chemicals. In this work flotation of apatite, calcite and silicate minerals from various industrial sources was investigated using laboratory and pilot plant-scale SIF machines. Flotation of diamonds was also investigated on laboratory scale. It was observed that all the minerals mentioned above can be successfully floated up to about 3 mm particle size. Beneficiation tests with the coarse fractions of classification circuits indicated that final grade calcite concentrate can be obtained with over 90% recovery in one SIF step in this grain size (typically 0,1 to 1,5 mm). Similarly, substantial upgrading of coarse apatite was achieved without grinding it to the fineness required by conventional flotation. SIF could also be applied to the recovery of coarse apatite from the tailings of a conventional flotation process. The capacity measured in the pilot plant test runs for a 1 m2 cell was typically 30 t/m2h. Presently, a full-scale process using the SIF technology is being installed for coarse apatite recovery.

Jan 1, 2003

By Philippe De Donato, Odile Barres, Mukendi Kongolo, Stoyan Gaydardzhiev, David Bastin, Jean-Marie Kanda

The adsorption patterns of potassium amylxanthate on the surface of high purity malachite subjected to prior sulfidization with NaSH have been followed and elucidated. DRIFTS spectroscopy has been used to trace the associated physicochemical alterations as well as the chemical species present on the mineral surface. Varying the collector concentration from 5.10-4 to 1.10-2 mol/L has led to different degree of surface coverage of the alkyl groups and to formation of organometallic hydrophobic complexes of CuX or CuX - X2 type. The results reveal that the CuX complex formed on the malachite surface without sulfidizing agent is more unstable and prone to dissolution-precipitation phenomena. Based upon the constructed adsorption isotherms and upon the degree of statistical coverage, different zones of mineral-reagent interactions could be distinguished. They correspond respectively to the monolayer, bi-layer and tridimensional condensation domains. In each of the identified zones mono or double layer adsorption patterns of the collector are proposed leading respectively to formation of surface compounds with different degree of hydrophobicity. The results suggest that sulfidisation remains an important prerequisite in view achieving efficient flotation of the malachite from the studied copper ore.

Jan 1, 2014

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By Sanja Miskovic, Manjunath Basavarajappa

In this study, a coupled CFD-DEM (Computational Fluid Dynamics-Discrete Element Method) approach is used to simulate two-phase, solid-liquid flow within the flotation cell. Turbulence plays a key role in flotation cells and level of turbulence is affected locally by the presence of particles. Turbulence in the flow is modelled using Reynolds Averaged Navier-Stokes (RANS) based k-e model. Using particle transport and spatial distribution, mixing mechanism for differed sized particles are analysed. By including the effects of particle-particle collision, particle rotation, and particle translation, as well as the volume occupied by the particles in the fluid, CFD-DEM approach can be used to accurately predict the motion of particles in the turbulent solid-liquid flows with strong coupling. Electrical resistance tomography (ERT) is used to investigate the effect of impeller size, shape, off-bottom clearance and impeller speed on mixing and suspension behaviour inside flotation cell. The effect of flotation impeller design, impeller size, and off-bottom clearance on flow hydrodynamics is investigated. In the case of moderate and high solids loading (> 10 %w/w), energy is dissipated through inter-particle interactions and four-way coupling becomes important (Derksen 2003). The main goal of this study is to understand the effect of particle size and concentration on flow dynamics at high Re in highly turbulent systems using advanced modelling and measurement techniques. Experimental measurements obtained by ERT) system allowed detailed mapping of temporal hold-up profiles of the dispersed phase. Impeller size and off-bottom clearance are found have significant effect on the particle suspension characteristics.

Jan 1, 2014

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

By M. Rudolph, D. H. Hoang, N. Kupka

"Froth flotation has been subjected to modelling since the 1930s and there is a large variety of approaches that intend to portray the entire process. Among these, three fundamental models could be considered exhaustive: the Pyke model [1], the Yoon model [2] and the Schwarz and Koh model [3]. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. Using a scheelite ore as a test case, a specific batch flotation test was repeated ten times and analyzed for chemical assays, mineralogical studies and froth properties. The detailed data are used to feed the three flotation models aforementioned in order to compare the outcomes of the three approaches, their capacity to reflect reality and to predict it. This article intends to pave the path towards reliable process models incorporating in depth mineralogy information, e.g. surface liberation, particle size and particle shape. KEYWORDS Froth flotation fundamental models, scheelite, automated mineralogy, critical assessment. INTRODUCTION In mineral processing, only three approaches aiming at describing froth flotation fundamentally could be considered exhaustive: Pyke’s collision and sliding approach [1], Yoon’s kinetic approach [2] and Schwarz and Koh’s approach [3]. The models will hereafter be referred to as Pyke model, Yoon model and Schwarz and Koh model. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. All three approaches rely on the widely accepted idea that flotation is a kinetic reaction dependent on a flotation rate constant kp, as expressed in Eq. [4]:"

Jan 1, 2018

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014