Search Documents

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By D. Saramak

Investigations over the application of hybrid comminution circuits with the High-Pressure Grinding Rolls (HPGR), on the main comminution stage on the basis of the lime and cement industry, were presented in the paper. Two crushing circuits were investigated, the first HPGR-based and the other one, with conventional jaw crusher. The results presented in the article confirm that hybrid comminution circuits with the application of HPGR are innovative ones, and they assure achieving the technological and economic competitiveness in the mineral raw materials processing industry. They are much more favorable in terms of the final product fineness and capacity but insignificantly less effective about the unit energy consumption. Technological performance of conventional crushing circuit and HPGR-based one were also compared in lab scale. The circuit with HPGR application gives finer products both on crushing and grinding stages. The average particle size reduction obtained in HPGR-based circuit is as much as twice greater, comparing to the conventional crushing devices. Keywords: comminution, HPGR technology

Sep 1, 2012

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Andrey Kozlov

The results of mineralogical?technological studies of PGM mineralization in zoned mafic?ultramafic complexes of the Ural?Alaskan type are given. The most important technological specificity of PGM mineralization hosted in dunites is its occurrence only in the form of free mineral species with predominance of Fe?Pt alloys (ferrous platinum, isoferroplatinum, and tetraferroplatinum). Technological properties, grain size, and good opening of PGM ore in grain size class +80 µm make it possible to concentrate ore using gravity methods with stadial comminution and between cycle separation of relatively large grains and nuggets into high-grade concentrates at the early stage of disintegration. Keywords: platiniferous dunites, PGM mineralization, mineralogical?technological studies and processibility research, recovery technology, gravity methods

Sep 1, 2012

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

By R. Chowdhury

Axis House manufactures and supplies alkylhydroxamate reagent of various carbon chain lengths for application in flotation of oxide copper and other minerals. As part of reagent performance improvement the structural factors of hydroxamate are examined by various analytical tools in particular with X-ray diffraction of single crystals. In a recent publication, the structure of n-octylhydroxamic acid and its corresponding potassium salt are presented with findings of hydroxamic functional group geometric preference, H-bonding, keto-enol tautomerisation, acid-salt aggregation and alignment of carbon chain. In this paper an example of branched alkylhydroxamate 3, 5, 5-trimethylhexylhydroxamate will be presented and compared with the result of linear alkylhydroxamate.

Sep 1, 2012

By A. P. Wang

Porous carbon adsorbents derived from inorganic materials templates such as zeolite and mesoporous silicate attracted considerable attention in the last decade and got great progress in re-cent years. However, so far almost all of templates used in the process were artificial porous materials; the porous carbons prepared by this method are very costly, which restricts the synthesis and application of templated porous carbons. In order to reduce the cost of templated porous carbons, natural inorganic porous minerals have been taken into consideration, which maybe possible and promising templates to prepare carbon adsorbents. In this work, we describe template process using tubular halloysite, rich mesoporous zeolite and low bulk density diatomite, as exemplars of the categories of inorganic porous templates which we have studied and discussed the effects of different templating structure on the resultant carbons. Two main carbon precursors, sucrose and furfuryl alcohol, were used respectively. The morphology of minerals and corresponding templated carbons were characterized using electron microscopy. The pore structures of minerals and templated carbons were characterised with nitrogen adsorption. The results showed that the morphology and pore structure of porous carbons are in good pertinence to those of corresponding templates. The morphology and pore structure of templated carbons could reflect those of corresponding templates at nanometer level. The templated carbons with high specific surface areas and rich mesopores can be prepared by using these three kinds of natural porous minerals as templates. The higher the surface area and pore volume of the minerals, the higher those of the corresponding carbons. The template carbons from halloysite possessed higher pore volume and mesoporosities. Based on the large mounts of experiment results, a model for the mechanism of resultant nanopores formation has been proposed. The nanopores of templated carbons are mainly composed of three kinds of pores: templated pores formed by removing mineral, hereditary pores formed by inheriting the pores of templates and nanopores formed during carbonization. These three kinds of pores have a close relationship with corresponding template.

Jan 1, 2014

By Sudhir Srivastava

India hosts a wide range of globally significant mineral resources, including four fuel minerals; 11 metallic minerals; 22 minor minerals and 52 non-metallic minerals. The country ranks among world?s top five nations for its commodity reserves of coal and iron ore. Interestingly, only small part of country's landmass has been explored that provides opportunity for future substantial mineral discoveries. India plans to double infrastructure investments to US$ 1trillion. Despite the challenges in infrastructure project implementation, mining sector remains a key driver of demand growth for commodities in the years to come with a good prospect to grow in future.

Sep 1, 2012

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By S. Banisi, E. Arghavani, M. Pourkani, M. J. Rajabi, Gh. A. Mohamadian, H. Bidshahri, Gh. A. Parsapour

The Sarcheshmeh copper complex flotation circuit of plant No.1 consists of two identical north and south sections where each includes four rougher (each bank consists of 14 cells), two cleaners (each bank consists of 8 cells), two recleaners (each bank consists of 2 cells), and two scavenger banks (each bank consists of 10 cells). The reduction of feed grade along with a change in the mineralogical composition is the main reason of current lower concentrate grade (24%) compared with the design concentrate grade (32%). Because of a lower feed grade, the amount of rougher concentrate has decreased which in turn has significantly reduced the feed rate to the cleaner, recleaner, and scavenger banks. This has increased the mean residence time of the material in the cleaner section resulting in a lower final concentrate grade. A laboratory study showed that the final concentrate grade can be increased by 2-4% if one cleaner stage is added to the flotation circuit. In this research, based on the laboratory results, one cleaning stage was added to the current flotation circuit. In order to make this modification instrumentally possible in the plant, the final concentrate was gravity transported to the Mo-Cu thickeners. This released 2 pumps and associated tanks which made addition of one cleaning stage practicable. Finally, a part of the cleaner and scavenger cells were used as the third cleaning stage. This decreased the residence time in the cleaner and scavenger banks. After implementation of one cleaning stage in the south section of the plant, the performance of the circuit compared with the identical north section. It was found that at the same recovery, the concentrate grade of the south section increased by 2.5%. The promising results led to the implementation of adding one cleaning stage in all sections of the flotation circuit.

Jan 1, 2018

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014