Search Documents

By Kaioeng Wang, Qi Liu, Yahui Xiang

"In the differential metal sulfide ore flotation it is desirable to replace the toxic inorganic depressants with environmentally benign chemicals. Chitosan, as a natural and non-toxic polymer, has been proven to be an efficient depressant for chalcopyrite while allowing galena to be floated by xanthate collectors. However, the poor solubility of chitosan limits its potential applications as the flotation could only be carried out at about pH 4 where chitosan is soluble. A carboxymethyl derivative of chitosan, named N-carboxymethyl chitosan (N-CMC), was synthesized by substituting the amino groups of chitosan with carboxymethyl groups. The substitution significantly improved the solubility of chitosan. The structure of N-CMC was studied and compared with chitosan via Fourier transform infrared spectroscopy (FTIR). Flotation tests were performed on single minerals and mineral mixtures (with weight ratio of 1:1) with the addition of appropriate amount of potassium ethyl xanthate (KEX) and N-CMC. The solution pH was varied from neutral to alkaline. The flotation concentrates and tailings were collected and analysed for the contents of copper and lead. FTIR measurements showed that new peaks of C=O stretching of -COOH and N-H deformation of -NH- appeared in N-CMC, which indicated that the carboxymethyl groups were introduced and the amino groups were the sites for the substitution. Flotation results indicated that N-CMC could depress either chalcopyrite or galena depending on the pH. The results were not affected by the sequence of KEX and N-CMC addition. Therefore, N-CMC is potentially useful in Cu-Pb sulfide separation following a bulk Cu-Pb flotation. The N-CMC was also found to have surface cleaning functions, and was able to remove contaminating copper ions from galena surfaces. Therefore, its application in sulfide ore flotation is expected to be more robust than the original chitosan."

Jan 1, 2014

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By Vladimir G. Kochnev

An innovative AG and SAG technology aimed to be applied in grinding of ores and in the production of construction materials is described. A novel design of a cantilever-type mill capable to operate in autogenous, semi-autogenous and ball grinding mode ensures easy delivery and installation even in remote areas, and low capital and operating costs. Results of the tests of the new heel-shaped liners performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation are reported. The approach includes also a novel discharge grid design and a technique of treating the material of critical size. These innovations make grinding in AG and SAG mills dramatically more effective, with an increase in the throughput rate and a reduction in power consumption ranging from 1.5 to 2 times.

Jan 1, 2003

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By Ronald Díaz

"Cerro Corona is a porphyry ore with different geometallurgical units and alterations produced by an extensive family of geological failures that have determined a special type of mineralization. With the increasing depth of the mine, it is estimated that the host rock will be less altered. Consequently, the ore will have a higher resistance to breakage accompanied by associated problems such as lower throughput. In light of this reality, various projects have been carried out with the objective to optimize mineral processing of ore with low clay content and high hardness, including reducing the blasting grid, increasing the load factor, using adequate mixtures of hard ore, reducing crusher settings, installing air guns in the transfer chutes, increasing ball charge, and changes in the lifter design, wear control in the hydrocyclones, syntonization of control logics, supervisor control of the SAG mil, characterization of feed ore, etc. However the most important factor was the teamwork between mine and plant personnel, aiming at common objectives for the company. These projects started in 2011, including characterization of mineralogical domains, breakage and blasting characteristics, and also a revision of the actual operating conditions in the crushing and grinding circuit. The development of different designs of the SAG mill lifters and the unloading grates, a 16% ball charge increase, improvements in the blasting process, reduction of the primary crusher setting, weight reduction on the feed lid, and variation of operational parameters, all allowed the company to achieve its objectives of maintaining impact control and steel recharge within the expected operational parameters. The achieved throughput is above design capacity, sustainable, and not without new challenges for maintaining and optimizing this production level."

Jan 1, 2014

By Xin Tan, Changgen Li

"The floatabiliby of chelate CF-collector for zinc and lead oxide minerals was described. It found that CF-collector possesses a strong collection power for zinc and lead oxide minerals as well as excellent selectivity for the gangue minerals. A new technology of zinc and lead oxide flotation with CF reagent as a collector, lead nitrite as a activator and water glass as modifier was presented. The mechanism of interaction between reagents and minerals was discussed by means of adsorption, zeta potential, nephelometric titration, XPS and infrared spectra was investigated.CF-collector, newly developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM), is a kind of chelate collector for the flotation of oxide minerals. CF-collector mainly consists of N-nitroso-N-phenylhydroxylamine ammonium salt. The CF-collector was used for the selective flotation of scheelite in the Chinese plants.In this paper, the effects of the dosages of activator Pb(NO3)2 and depressants (sodium hexametaphosphate, polyphosphate, water glass and salified water glass) on the floatabilities of several minerals (cerussite, smithsonite, calcite, dolomite, limonite and quartz) as well as their mixtures were investigated in the presence of the CF-collector. The results show that the CF-collector is the excellent collector for selective flotation of cerussite and smithsonite. Pb(NO3)2 can selectively activate the oxides of lead and zinc resulting in a decrease of the CF-collector dosage. The sodium hexametaphosphate plus the salified water glass are the effective depressants for gangue minerals. Based on the above facts, the “CF process”, namely, used CF reagent as a collector, Pb (NO3) 2 as a activator, and sodium hexametaphosphate plus salified water glass as depressant, has been used for the flotation separation of the lead oxide mixtures or zinc oxide mixtures without disliking and heating. For the feed lead assaying 19.07%, the lead concentrate assaying 49.81% Pb at the recovery 80.69% was obtained after one step flotation. For the feed zinc assaying 12.85%, a zinc concentrate of assaying 29.56% Zn at recovery 83.87% was obtained."

Jan 1, 2003

By Ayumu Tokumaru, Shuji Owada, Gangfeng Liu

"Several million spent catalytic converters are disposed annually worldwideandeach containing about 0.5-1g ofplatinum and 1-2g of all the platinum group metals (PGMs), then,it is fairly significant to recover PGMs from the spent automobile catalyst. The PGMs’ recovery is a proven technology, including pyro-and hydrometallurgicalmethods, and the highestrecovery can achieve approx. 98 wt.% by acid-leaching method, but theserecyclingtechnology seems to be too highlyenergy-consuming. SincePGMs aredistributed only in coat layer in spent catalyst, it is of great significance to enrich the coat layerwith some physical methods as a pretreatment.In this paper, according to the double-deck structureof the catalyst andthe different properties of the two main compositions, alumina-ceria phase of coat layer and cordieritephase of substrate, the concentration of the coat layer was investigated by combiningthree kinds of physical separation technologies, heating-quenching, crushing and surface grinding. In the first stage, thermal stresscouldgeneratebetween the two phasesby thermal expansion difference,to producefracturesin the thinnest part of coat layerand micro-cracksin coat layerand at the interface of coat layerand cordierite substrate. The second stage of crushing, by jaw and roll crushers, could break dominantly the coat layer and the third stage of surface grinding, carried out by attritor, promoted further separation and concentration of coat layer fromthe substrate.We also improved the attritor grinding by adding a new lift-arm to the cell for achieving better mobility of sample particles in the selective surface grinding."

Jan 1, 2014

By Hermann Wotruba, Günther Petzold, Fabian Riedel

"Increased mechanisation in underground stoping operations results in higher waste percentages in the run of mine. A new method of reducing waste is optical sorting. Optical sorters have low maintenance costs and can be installed underground. Rejected waste can be backfilled directly without having to be hoisted, therefore increasing the shaft capacity for a more valuable product.Pre-Concentration by Optical SortingA series of tests with an optical sorter at the laboratories of the Mineral Processing Department of the RWTH Aachen have shown that it is technically possible to sort almost any kind of ROM which has even slight differences in colour (Platinum Reef, Gold Reef, Kimberlites, Industrial Minerals, Aggregates, Coal, etc.).By employing optical sorters prior to conventional sorting plants, it is possible to reduce the amount of waste to be processed. Figure one shows test results of ore which is quite similar in colour to the waste (grey). With increasing waste in the feed, the recovery decreases according to the graph. In figure two, the colour ratio parameter of the sorter was changed with a similar waste percentage in the feed. With increasing loss of ore, a cleaner product can be achieved. Before designing a sorting plant, throughput tests are carried out. Throughputs vary depending on the size range. Sorters have a limit of about 250mm top size. In this upper size range, throughputs of 150t/h can be achieved."

Jan 1, 2003

By Renato Oliveira, Walter Valery, Alex Jankovic, Birol Sönmez

"The ball mill is the most common ore grinding technology today, and probably more than 50% of the total world energy consumption for ore grinding is consumed in ball mills. On the other hand, high pressure grinding roll (HPGR) technology is relatively new to the mining industry, with significant application only since the beginning of the 21st century. Both ball mills and HPGRs are typically used in closed circuit with classifiers. There is a general consensus within the industry that classification efficiency and circulating load both have a major effect on the efficiency of closed circuit ball mills. Metso Process Technology & Innovation (PTI) conducted a laboratory test program to understand the relationship between classification efficiency and circulating load, and the impact on the performance and capacity of ball mill circuits. However, the effects on HPGR performance are significantly different. Metso PTI has initiated a pilot scale test program to evaluate the size reduction performance of the HPGR under different circuit configurations. A series of pilot scale HPGR locked cycle tests were performed to simulate the following circuit configurations: including closed circuit with a screen, partial product recycle and edge recycle. This paper discusses the results from the pilot scale HPGR and laboratory scale ball mill test programs. The effect of circulating load and classification efficiency on the performance of ball mill circuits is compared to the effect on HPGR circuits. The fundamentals of grinding behavior are also discussed in order to explain the difference."

Jan 1, 2014

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By S. M. Marr

"Water availability and water-related environmental impacts are now one of the most significant challenges facing primary production within the global minerals industry. Whereas the industry has, to a large degree, been able to demonstrate a collective response to greenhouse gas emissions and global energy demand, no such strategy exists for water. In part, this is because water quality and availability are regional issues, but also too because water quality cannot be defined by a single attribute, and extrapolation of any set of water quality indices to their associated environmental impact is no trivial matter. In design situations specifically, the situation is exacerbated by the fact that process engineers typically focus on site water management, and consent authorities are primarily in catchment level issues. As a result, an integrated approach to water management is difficult. This does not stem from an unwillingness by members of the professional team to engage with the total picture of water quality and availability, but principally from the fact that there is no common language through which to approach the problem.It is imperative for process engineers to extend their design system boundary, to reflect the geographic scales over which water impacts need to be quantified. It is not suggested that chemical engineers and metallurgists should become experts in geochemistry, hydrology and limnology. Rather, the challenge is to develop tools through which better communication of the relevant environmental impacts can be achieved.It has been estimated that 50% of the capital for new plants is devoted to handling wastes. The integration of mass exchange processes, adopting a life cycle analysis framework for considering environmental impacts and shifting the emphasis from effluent concentration to environmental impacts should be adopted in the framing of the design problem have been suggested as techniques of Environmentally Conscious Design. Shifting the focus from effluent concentrations and legislative requirements to evaluating the environmental impact is an important step towards improving the overall environmental performance of a process facility."

Jan 1, 2003

By D. G. Hulbert

"Mineral processes are complex operations that have been modelled, controlled and simulated by diverse technologies. A review is given of some models of mineral processes in the literature. A new variation of a dynamic process model of flotation is presented. Process models, describing real and relevant physical variables, give a good understanding and good qualitative simulations, but can sometimes require prohibitively difficult and extensive parameter estimations. Process control is usually best done on operational plants by the fitting of system models, which can home in on the plant?s observability, controllability and optimisation. System models can be of a form amenable for use in appropriate techniques for controller design and implementation. The control of milling circuits is discussed in some detail. While simulators use models to predict dynamic or steady-state information, part of their strength lies in their ease of use and their ability to test different types of specifications. Some results are given for a flotation circuit simulator that can be made to solve virtually any permutation of specifications.INTRODUCTIONThe development and application of appropriate technology can lead to better operation of mineral processing plants in industry, so that substantial benefits can be obtained from improved throughputs, efficiencies and product qualities. This paper addresses some of the principles and methods used in the quest for the development and exploitation of such technology. Although the design of processes is often the motivation for modelling and simulation, this paper also targets the use of modelling and simulation for the control and optimum operation of mineral processes. The two processes given the most attention here are flotation and milling.Technologies used in mineral processing range from simple to very complex. Simple technical principles, such as mass and component balances, can yield some simple and effective strategies for modelling and control. However, minerals in particulate form have such complex physical and chemical properties that there appears no end to the complexity that emerges, as more and more factors are taken into consideration in the pursuit of better results and understanding. The situation is aggravated by the complexity of mineral processing plants, which have spatially variable conditions within process units, and complicated interactions between these units."

Jan 1, 2003

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Yong Liu, Peng Qian, Shu-Feng Ye, Shao-Jun Chu, Pei-Wei Han

"Chromite with a low mass ratio of Cr to Fe (Cr/Fe ratio) was treated by the carbochlorination method using solid chlorinating agent (MgCl2 and CaCl2) and carbon in the present paper. The results showed that iron could be selective removed mainly in the form of FeCl2. The removal of iron was indirectly, which consisted of the decomposition of solid chlorinating agent to release Cl2/HCl and the carbochlorination of FeO•Cr2O3 by Cl2/HCl and C. The Cr/Fe ratio increased as increasing temperature from 700 ? to 900 ? in air atmosphere, while the tendency was opposite in N2 atmosphere. The removal efficiency of iron by CaCl2 was better than that by MgCl2. At last, a new pelletizing process was proposed to treat fine chromite with a low Cr/Fe ratio based on carbochlorination method, which could produce the high quality roasted chromite pellets with higher Cr/Fe ratio and compressive strength. INTRODUCTION Chromite is mainly used for the production of ferrochromium. A high Cr/Fe ratio (>2) of chromite is usually required to meet the technical specification of ferrochromium.(Gasik, 2013) Attentions have been attracted to the economic and efficient methods for the recovery of chromium from lower-grade ores as the higher-grade ores become depleted. However, the Cr/Fe ratio is difficult to improve through the conventional beneficiation methods (such as gravity concentration, flotation) due to the spinel composition, although beneficiation methods could increase the metal content of chromite ores by removing gangues.(Nafziger, 1982) The main industrial mineral of chromite is (Fe,Mg)O•(Cr,Al,Fe)2O3, which belongs to spinel magnetite.(Liu, 2013) Iron should be selectively removed through the structural dissociation of spinel to increase Cr/Fe ratio.(Nafziger, 1982)"

Jan 1, 2018

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018