Search Documents

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By Mike Neill, O&apos

? Bypass soft soils near the surface ? Resist uplift loads ? Resist lateral loads ? Bypass scourable soils ? Bypass liquefyable soils ? Mitigate movement of expansive or frozen soils ? "Tune" foundations for vibrating machinery

Jan 1, 1998

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000