Search Documents

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By Craig Roberts

"While various methods are available to estimate a mining project's value, value is only established through a transaction. Comparable methods allow the value estimated for a mining project to be benchmarked against mining project values established in the market. Comparable methods thus are a key tool for ensuring value estimates are congruent with what the market would actually pay. For example, if the value estimated for a mining project using discounted cash flow analysis differs significantly from the value implied using comparable market methods, the valuator may be using metal price or discount rate assumptions that differ significantly from those the market is currently willing to pay for.The paper provides an overview of market comparable valuation approaches, and discusses some of the difficulties and limitations that arise in using these approaches. The types of market values that are typically utilised are discussed, including asset sale prices, share prices (market capitalisations), and values established in corporate mergers and acquisitions. Topics discussed include methods used in estimating a mining project's value based on the market value of the company that holds the asset, and limitations that arise because of unique features of mining projects and of companies that hold them.It is concluded that market comparable and fundamental (e.g. NPV) approaches to project valuation should not be viewed as alternative approaches to estimating project value, but rather can and should be integrated to derive a single value estimate based on both market andfandamental data. A method for integrating these approaches is discussed, and illustrated by example."

Jan 1, 2003

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By Jennifer Abols

In July of 2013, Lundin Mining acquired the 2,000 tpd Eagle nickel and copper project from Rio Tinto. The project had been put on hold earlier in the year and construction was approximately 50% complete. Lundin immediately accelerated project activities and by September of 2014 the project was constructed, commissioned and ramping up. The newly commissioned facilities went on to reach design throughput, recovery and product quality targets by the end of the year. This was accomplished ahead of schedule and below budget despite numerous obstacles including the worst winter on record in the past 50 years for the area. What led to the success of the project, and in particular the commissioning phase of the project? This paper takes a high level look back and provides an overview of the methodology used, key issues encountered and lessons learned to answer this question.

Jan 1, 2015

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The &apos;actual performance&apos; speed-curve of aircraft plotted over a ten-year period is rising faster than the &apos;expectancy&apos; speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By Knud Sinding

Many industries have established their own systems for self-regulation. They often do so when companies operate in countries where financial, technical, environmental and social regulation is weak and when the industry is challenged by legitimacy issues related to behaviour in one of these areas. Mining is one industry that has progressed unevenly down the road of self-regulation in these areas. This paper examines how the development of self-regulation for mines and mining companies involves difficult questions of scope, rules, membership, assessment criteria and performance evaluation. Using a range of theoretical and empirical results from research on self-regulation, performance rating and corporate strategy, this paper analyses the strategic and operational issues related to the idea of self-regulation in the mining industry. The analysis indicates that while self-regulation may bring benefits to members, they are likely to take a long time coming; but when they do arrive they may be substantial. Using the fact that in relation to technical and financial issues the industry is quite experienced in self-regulation ? not least as it is more reluctant in areas such as environmental and social performance ? the case is made for a comprehensive and innovative approach, that draws on the areas where the industry is experienced and develops new institutional solutions in the areas where the industry is more reluctant.

Aug 1, 2013

By M. Holm

Coal is an important fuel for energy generation, and since there are no adequate alternatives it will also be for the next decades. The deep lying hard coal is important in particular because of its high energy content. Automation of underground mining has led to major improvements in productivity and safety. A fully mechanized longwall shearer workface has already reached a high degree of automation and provides a high productivity for example utilizing the memory cut. Current researches and developments in longwall mining are focused on extending this method by adaptive cutting drum height adjustment. The so-called horizon control is often based on memory cut methods. Horizon control in this way requires information of the environment, which can be provided by models (seam model, cut model) and coal interface detection (CID). Available CID systems only provide an optimal output under specific conditions. The authors propose the shield-data-based horizon control (SDHC) system as an alternative approach. SDHC does not require information from a CID system or an environmental model. All necessary information is provided by roof supports, shearer and process monitoring. The SDHC system was tested in simulation under different seam conditions and yielded promising results which will be presented in this paper. In cooperation with the German mining company RAG the SDHC has already reached an experimental stage. A test assembly was built up at the surface and the SDHC system was implemented on real mining equipment. To make the test scenario as realistic as possible, the SDHC system was only connected to the monitoring system, not to the simulation model. The aim of these tests was to establish the cooperation between all subsystems, find appropriate controller parameters, locate and address safety critical aspects and finally to achieve an automatic cutting drum height adjustment. An introduction of SDHC for shearer guidance is given in this paper. The experimental tests are described and the control results of the realized SDHC system on the test assembly are shown.

Aug 1, 2013

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By S. Dallaire

"RÉSUMÉLes revêtements céramiques ont une moins grande visibilité que les revêtements métallurgiques. Ils ont cependant jour un role significatif dans noire développement technologique. Les procédés de revêtement ont permis de s&apos;affranchir de barrières technologiques importantes dans le domaine de l&apos;optique, de l&apos;électronique, de l&apos;usure, des hautes temperatures. L&apos;introduction de nouvelles technologies ou la mise en service de nouveaux matériaux peut nécessiter l&apos;adaptation de certain procédés actuels ou le recours a des procédés qui ont peu percé jusqu’ à maintenant.ABSTRACTApplications concerned with ceramic coatings are not as well known as those with metallic coatings. However, ceramic coatings have played a tremendous role in the development of technology. Ceramic coating processes made it possible to overcome technological barriers in the areas of optics, electronics, wear resistance and high temperature applications. Ceramic coatings can provide new properties to materials never considered for demanding applications. They can also open new frontiers and revitalize materials which are maturing or in decline."

Jan 1, 1990

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By Mike Broczkowski, Laura Dewhirst, Kieran Large, Angelo R. Fernando, Heather Daigneault, Jim Johnson, Randy Wiens

The radioactive isotope radium 226 is a contaminant of potential concern in effluent waters from metal mining operations in Canada. Acceptable release levels of radium 226 are governed by Metal and Diamond Mining Effluent Regulations. Since radium is invariably present as a companion element in uranium ore, monitoring and controlling of radium 226 is a must for uranium mining operations. Measurement of radium 226 is traditionally carried out through a radiochemical technique involving selective co-precipitation of radium with barium sulphate followed by alpha spectroscopy for quantification. As of 2010, Cameco has also been using an ICP-MS based radium analysis method developed in collaboration with a research team at Trent University, Peterborough, Ontario. This method, which is highly automated and requires significantly less sample handling, with improved turn-around-times, is being used by Cameco site laboratories at the McArthur River and Cigar Lake mines as well as the Port Hope Conversion Facility. This paper compares the benefits and drawbacks of this new method, compared to the traditional alpha counting procedure drawing from almost ten years of field experience.

Jan 1, 2020