Search Documents

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

For developing new technologies, it is important to characterize the microstructure of materials with high spatial resolution at the nanoscale. To achieve high resolution, field emission scanning electron microscopes (FE-SEM) were developed. These microscopes allow working at low accelerating voltage, below 5 kV, to take advantage of the reduction of the interaction volume with accelerating voltage. Furthermore, their higher gun brightness compared to conventional thermo-electronic emitters, allow a probe size at the nanoscale. At low accelerating voltage, the emission volume of backscatter and secondary electron (SE) of the type II signals approach that of SEI signals. However, it is not enough to reach the highest resolution. A magnetic field above the sample improves the spatial resolution by collecting mostly high-resolution signals. In addition, the energy-filtration of the electron signals allows selecting the type of contrast detected: topographic, compositional, or crystallographic. The development of these new technologies permits to extend the imaging capabilities of the SEM towards new nanoscale applications.

Jan 1, 2014

By R. Horn

The financial performance of the mining industry, measured by return on equity and capital employed, has been inadequate for many years. Consequently, mining companies are not valued highly by stock markets. Among the more important causes for the decline in the sector are the conservative working practices and reluctance to adapt to change or to develop new technology, although some relatively recent developments such as SX-EW copper and heap leach gold have made a significant impact on the cost base of these metals. The subsidiary business of metals exploration suffers from the same problems as the rest of the industry. The rate of discovery of ore deposits has been falling over many years and since the late 1990s, there has been a sharp reduction in global exploration activity that, if it continues, will further reduce the global supply of new ore reserves. New technological developments, particularly in geophysics and different operational practices may help reverse this trend. Statistical methods for evaluating the risk of ore reserve estimates will also improve the economic return on new mining ventures. The science of ore geology has potential to reduce exploration risk, but modern ore genetic theory has not contributed greatly to recent discoveries. The junior exploration market has almost ceased, but a new style of technically specialized efficient small exploration company has emerged which, in alliances with major companies, may be the vehicle for future global exploration. Exploration in virgin terrains has a higher risk discounted potential for the discovery of very large orebodies than that in known mining districts but mining companies have little financial incentive for this high risk exploration because of the very long lead time to production. Alliances of two or more companies reduce the risk in both the exploration for and development of major new mining projects. If new orebodies are not found, then metal prices will inevitably rise in the long term. Governments of industrial countries, particularly those with a significant mining industry such as Canada, should therefore provide assistance to exploration in order to maintain their existing industry and prevent a metals shortage from developing in the future with its consequent impact on the world economy and increased environmental damage as large lowgrade orebodies are developed to supply an expanding market.

Jan 1, 2002

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

"Cambior currently has nearly 80 exploration properties, acting as operator on about 60 of these. The company's exploration budget has increased to over $11,100,000 for 1990. On-going efforts recently yielded a new gold discovery on the Douay- Vezza property, a joint venture project with Inco and Vior. Cambior continues to seek out new opportunities, recently acquiring an option agreement on the Sleeping Giant project in Quebec and four new exploration agreements in the United States, through its Reno office. Other nearly-concluded joint venture agreements have also given the company entries into Indonesia and Guyana.SummaryWhen it acquired SOQUEM's assets on August I, 1986, Cambior also acquired interests in 45 exploration projects. The subsequent mergers with Aiguebelle Resources and Sullivan Mines in 1987 brought the total number of exploration projects to 83, most of which are concentrated in northwestern Quebec. Cambior's strategy emphasizes gold exploration, and exploration activities were, therefore, initially limited to the Val d'Or and Rouyn-Noranda mining camps, where Cambior has a large portfolio of properties. Approximately $25.8 million has been spent on surface exploration in this area since the formation of the company, resulting in the discovery of the Mouska deposit and four sub-economic zones on the Porcupine, Forbex, Bloc Sud and Flavrian project s. In 1988, Cambior became involved in projects in the United States to which the company expects to allocate about 38070 of its 1989 exploration budget."

Jan 1, 1990

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario 's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario' s clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom.Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain , art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual"

Jan 1, 1988

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario's clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom. Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain, art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual upgrading and consolidation of them as traced in Table I"

Jan 1, 1988

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By E. Wright

"INTRODUCTIONThe Ruttan Mine is located twenty-two km east of Leaf Rapids in northwestern Manitoba. The copper-zinc exhalative massive sulphide deposit is comprised of a series of individual and interconnected en echelon lenses which strike east 20 degrees north and dip south 70 degrees. The mine has been owned and operated by the Hudson Bay Mining & Smelting Company since July 1987. Sherritt Gordon Mines Limited began mining the orebody in 1973 from an open pit, but production has been entirely from underground since 1980. HistoryDuring the progression from open pit to underground mining, it was recognized that manual methods of ore reserve calculation were inadequate for responding to changing metal prices and evaluating alternative mine plans. The mine planning system that was developed is described in the paper, ""Computerization of Ore Reserves and Mine Planning Functions at Ruttan Mine"", presented by B.C.W. Haystead at the 1984CIM Annual General Meeting. At that time, programs for core logging, diamond drill hole plotting, grade interpolation, ore outline digitizing, and reporting had been developed by the Systems Department for use on Sherritt's UNIVAC 1100 mainframe computer. Telecommunications linked terminals at the Ruttan coreshack and office to the UNIVAC in Fort Saskatchewan, Alberta. The same mine planning system was also used at a second property.Operation of the mine planning system was expensive, and it was evident that increased use required a costly upgrading of the UNIVAC in order to maintain an acceptable service level to all users. The system was re-evaluated,' and it was concluded that: core logging was not easily adaptable to a new property, nor flexible enough for exploration; plotting, grade interpolation, and digitizing required considerable manual effort; and that the UNIVAC operating system was difficult to learn.It was recommended that a study should determine if: core logging could be redesigned and/or implemented on a microcomputer; interactive graphics be used to reduce the effort for functions requiring visual interpretation; and the creation of input processors would assist users in setting up parameters for guiding the programs."

Jan 1, 1989

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By W. P. Nash, T. E. Mccandless

"Abstract - Detrital minerals of upper mantle origin occur in Holocene conglomerates, pediments and antmounds, and in Oligocene conglomerates in the Green River Basin of southwestern Wyoming. The minerals are derived from disaggregated eclogite and peridotite, and are similar to minerals found in mantle- derived igneous rocks such as kimberlite and lamproite, the primary host rocks for diamond. The Green River Basin bisects the lamproite fields of the Leucite Hills (Wyoming) and Kamas (Utah) and overlies the Archean Wyoming craton, which makes the region favorable for diamond occurrence. Lamproite is the favored host for the indicator minerals because unusual high-Fe salitic diopside macrocrysts from the antmounds and from the ~1 Ma old Leucite Hills lamproites to the northeast are compositionally identical. The salitic diopside is uncommon in other igneous rocks and could be a new indicator mineral for use in lamproite exploration. The Green River Basin indicator minerals are eroded from the ~29 Ma old Bishop Conglomerate, whose source area is the Uinta Mountains to the south. No continuous mineral train exists between the Uinta occurrences and those in the Green River Basin. Assessment of the minerals using established and new geochemical criteria indicate that they formed in an oxidizing upper mantle and were transported to the surface by either kimberlite or lamproite. The existence of cogenetic diamond is unlikely based on the mineral chemistry, but selective removal of diamond indicator minerals through weathering and fluvial transport cannot be excluded. Diamonds and mantle garnets are present in the northeastern Uinta Mountains, but they originated as part of the Diamond Hoax of 1872. A representative mineral assemblage from the true igneous host of the indicator minerals is required to fully establish their economic potential. Post-Oligocene erosion and Pleistocene glaciation have hindered efforts to locate a bona fide igneous source for the indicator minerals. Résumé - Des minéraux détritiques provenant du manteau supérieur ont été trouvés dans des conglomérats, des pédiments et des monticules de fourmis de l’Holocéne, et dans des conglomérats de l’Oligocène du Green River Basin, au sud-ouest du Wyoming. Ces minéraux sont issus du démantellement d’éclogites et de péridotites, et sont semblables aux minéraux trouvés dans des roches ignées provenant du manteau, comme les kimberlites et les lamproïtes. Ces dernières sont les roches hôtes du diamant. Le Green River Basin recoupe les champs à lamproïte de Leucite Hills, au Wyoming et de Kamas en Utah, et il surmonte le craton archéen du Wyoming, connu pour la présence de ses diamants. La lamproïte est l’encaissant privilégié pour les minéraux «indicateurs» parce que des macrocristaux exceptionnels de diopsides salitiques riches en Fer, provenant des monticules de fourmis et des lamproïtes de Leucite Hill (~1 Ma), au nord-est, ont des compositions identiques. Le diopside salitique est rare dans les autres roches ignées et peut être un nouvel indicateur dans la recherche de lamproïte. Les minéraux «indicateurs» du Green River Basin proviennent de l’érosion du Conglomérat de Bishop, daté de ~29 Ma, dont la zone source est représentée par les Uinta Mountains, au sud. Aucune continuité des gisements minéraux n’existe entre les affleurements de Uinta et ceux du Green River Basin. La détermination des minéraux, utilisant des critères géochimiques anciens et récents, indique qu’ils se sont formés dans un manteau supérieur oxydant et qu’ils ont été remontés à la surface soit dans des kimberlites, soit dans des lamproïtes. La genèse du diamant n’est que peu liée à la chimie minérale, mais le lessivage d’indicateurs minéraux du diamant par altération météorique et par transport fluviatile ne peut être exclu. Des diamants et des grenats mantelliques sont présents dans le nord-est des Uinta Mountains, mais sont associés avec le Diamant Hoax de 1872. Un assemblage minéral représentati"

Jan 1, 1996

By H. Sato, Y. Sato, T. Ooishi, K. Sakamoto

"Sumitomo Metal Mining Co., Ltd.(SMM)'s Niihama Nickel Refinery(NNR) produces high quality Nickel cathode, Cobaltcathode and other by-products using hydrometallurgical refining process called “MCLE”(Matte Chlorine Leach and Electro-Winning). In 2005,NNR started to use nickel and cobalt mixed sulfide (MS) produced by one of the SMM’s subsidiaries Coral Bay Nickel Corporation(CBNC)’s HPAL plant in Philippines, although its main and the only raw material until then was nickel matte. With start-up of the second HPAL plant at Taganito in 2013, NNR expanded its production capacity of nickel cathode from 41,000 to 65,000 tpa and finally achieved its target in 2015 by producing 65,980 tpa. SMM developed the technologies to improve poor reactivity of MS and installed new facilities to cope with increased Cobalt and Sulfur production at that time. This paper describes the technical approach to increase MS treatment with high efficiency.INTRODUCTIONThe Sumitomo Metal Mining Co., Ltd.(SMM)Niihama Nickel Refinery(NNR) produces Nickel cathode, Cobalt cathode and other by-products using Matte Chlorine Leach and Electro-Winning (MCLE) process technology. SMM uses nickel matte and nickel & cobalt mixed sulfide (MS) as raw materials for the MCLE process. Table 1 shows typical composition of these raw materials. Nickel matte had been only raw material until 2005, and with start-up of Coral Bay Nickel Corporation (CBNC) operation in the Republic of the Philippines, MS became major part of it. In 2009, when CBNC doubled its production capacity, NNR also expanded its plant capacity of electrolytic nickel from 36ktpa to 41ktpa, keeping an eye on the possibility of 65ktpa with oncoming SMM’s second HPAL in Philippines. Poor reactivity of MS was the prime concern at that time because our intention was to increase production with MS. Nickel extraction rate deteriorated with increasing usage ratio of MS in raw materials. To keep high nickel extraction rate under high ratio of MS, NNR developed a new leaching technology. Another concern arising from treatment of MS was Cobalt and Sulfur contents that are much more than those of nickel matte as shown in Table 1.NNR introduced new technology of solvent extraction process as to Co/Ni separation process in order to keep cost competitiveness instead of the conventional cobalt oxidation–neutralizing method. As to sulfur products, new sulfur productive facility was installed to improve the exposure to sulfur dust and the hot working conditions for workers. As a result of process development and installation of new facilities against the problem with MSusage,65 ktpa production was achieved in 2015."

Jan 1, 2017

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017