Search Documents

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies' requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite's unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

By Ferrin Prince

New Gold?s New Afton mine is an 11,000 tonne per day block caving mine, located 8 km west of the city of Kamloops, British Columbia. The reserve is estimated at 52.5Mt with grades of 0.65 g/t Au and 0.93% Cu. Block caving requires a considerable amount of infrastructure development before production can begin. Each excavation had its own challenges, often further complicated by interactions with the caving stresses and fault structures. The main areas of interest were: the production crusher complex, the surface to underground infrastructure, and the footprint interaction with the faults. The ore zone at New Afton is bounded by two very weak fault zones, with large fault affected areas and associated splays. The resulting rock mass rating (RMR) is 35-50, with some areas significantly weaker due to clay infill. These conditions created a unique and decidedly difficult environment in which to develop New Afton?s infrastructure. Despite these difficulties, the mine began production on schedule in July 2012. The main production crusher for the mine is a gyratory crusher that allows for direct truck dumping, with a smaller jaw crusher in series to facilitate the initial development and production. The crusher chamber was redesigned several times to minimize the chamber volume, resulting in a 40% decrease in volume without losing functionality. After drilling and geotechnical testing, the location of the crusher was changed to eliminate the threat of fault affected ground in the area; the entire complex moved a short time before mining began on the chamber. The mining techniques used enabled tight control of the crusher pocket excavation, while also allowing for the timely completion of the chamber. The locations of the surface to underground infrastructure were tightly constrained by geology, surface infrastructure, and an existing open pit. The VR5 raise was drilled and abandoned part way through the reaming process when the drill string became stuck in fault gouge material. It was relocated and successfully completed. The VR7 raise hit a region of poor rock strength and deviated more than 11 m. Poor ground conditions caused a 130m section of the raise walls to fail. An innovative rehabilitation program was undertaken to re-establish the raise for ventilation. A surface to underground slick line was also installed to ease the material movement underground. A layout of the Extraction level was changed from herring bone to straight through drawpoints that resulted in a net reduction of 1.3 km of development. The Apex level was added to aid in the breakage over the major apex pillar and allow for geological mapping. A portion of the caving footprint is located within the footwall fault. The low strength, high clay content, and small joint spacing of the material resulted in blast-hole cut-off and drift deformation. Drift rehabilitation was a key factor in the successful development of the cave footprint. Innovative drilling and loading techniques were used to keep the holes open and to impede movement along the joint structures.

Aug 1, 2013

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By Douglas A. Sloan

"Recently, a number of major mining companies seemed unable to find a president from within the industry, and were searching outside the industry. From this, one could conclude that managers within the industry are either not being prepared or are not preparing themselves for presidential responsibility. Opinions were sought from a number of senior executives, to attempt to define the skills a prospective president should acquire and what actions a company could take or that a prospective president could take to acquire these skills.This paper contains summaries of the opinions obtained, along with the author's comments. The paper also describes the actions some companies are taking and the actions that an aspiring president can take to prepare himself for corporate management.IntroductionA manager is promoted up the management ladder when the manager's superiors believe that he is capable of handling a more senior position. Normally, the manager acquires this credibility by outstanding performance in his current management post, whether it be in a junior management (supervisory) or in a vice-presidential capacity.In most instances, the skills required for promotion can be acquired in the current position or, at worst, the abilities exhibited in a candidate's current role will convince his superiors that the necessary expertise for the more senior position can be acquired on-the-job. This is particularly the case when the new skills are felt to be an extrapolation of the old skills.However, in the case of appointment to presidential rank, there appears to be a need for new expertise which often is not acquired in normal management progression or, at least, boards of directors of some mining companies seem to believe this to be the case. The objective of this paper is to attempt to define the new skills that should be acquired by a manager who aspires to be the president, and to describe what actions might be taken by him to acquire them."

Jan 1, 1982

By Constantin Pitis, Paul Slatter, Behnam Pirouz, Laura Contasti, Markus Zeller, Sadegh Javadi

"The centrifugal slurry pumps feeding cyclones are critical components used in the grinding process. It is well known that for this type of pumps the performance degradation is very intense. To minimize downtime a complete stand-by slurry pump is always installed in a parallel circuit. The replacement decision of slurry pumps is sometimes set on specific periods of time that are empirically determined, based on previous experience; unless a pump failure triggers the second (standby) pump. Given the significant energy costs in the grinding process and a desire to increase competitiveness, engineers and scientists started research in this field while manufacturers also took actions in order to improve pumps reliability and performance. The lack of standardization regarding the methods used to benchmark and evaluate the energy performances of cyclone slurry pump systems in the mining industry makes it difficult for an enterprise to take informed decisions concerning the replacement or optimization of its process based on energy benchmarking of such slurry pump systems. This paper proposes a new methodology of benchmarking slurry pump performances using a new concept of Benchmark Energy factor (BEF) based on Mathematical Model Benchmarking. The concept of BEF has been proven successful in other industries. A new standard addressing the guidelines for benchmarking the energy performance of slurry pumps for cyclones was proposed within the Canadian Standards Association. This standard will provide a unified and consistent methodology for performing measurement activities with the ability to measure and verify the system energy performance in the field through the BEF approach. Practical examples based on the new concept are presented with comments."

Jan 1, 2017

By T. Nomura, N. Saitoh, K. Tamaoki, Y. Konishi

We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from end-of-life products and electronics. We have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, that are able to reduce and deposit gold ions (Au(III)) or PGMs ions (Pd(II), Pt(IV) and Rh(III)) into metal nanoparticles at room temperature within 120 min. When processing the aqua regia leachate of printed circuit boards, Shewanella bacteria were able to rapidly and selectively collect gold ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. This biotechnological procedure also has the potential to allow the recovery of PGMs from the leachate of automotive catalysts. Shewanella bacteria were also able to successfully perform the complete reduction and deposition of the PGM ions. The ability to collect the PGM ions suggests that this represents a new process for the biorecovery of PGMs from used automotive catalysts. Our proposed biological method enables the rapid and highly efficient recovery of precious and rare metals via separation and concentration utilizing microbial reactions at room temperature.

Jan 1, 2014

By F. Kitzinger

Electromagnetic testing of wire rope has become more and more reliable over the past two decades. This improvement is partly a result of an unprecedented progress of electronic technology, which permitted the development of a new breed of testing instruments. There are two basic methods for the electromagnetic testing of wire ropes, the AC method and the DC method. Both methods rely on magnetic field disturbance caused by mechanical anomalies in the rope structure. The wire rope under test is passed through a magnetic excitation field, which can be a weak alternating field or a strong static field. Because the alternating field is produced by an alternating current, these instruments are of the AC type(l). In the early days of ND-testing, strong permanent magnets were not yet available; therefore, the static magnetic field was produced electromagnetically with direct current. Instruments based on static excitation are still called DC instruments(2), even though the field is now produced by a permanent magnet. Both these methods have certain characteristic features. The AC method can detect loss of metallic area caused by corrosion or other effects, whereas localized faults such as broken wires are better detected by the DC instruments . The basic principles of the wire rope testers have remained unchanged over the years and the improvements present in the new instruments usually reside in the signal processing and recording sections. The Instrumentation Department of the Noranda Research Centre* has been involved in a four-year development program which resulted in a new type of wire rope tester, the Magnographv** . This new instrument in many ways represents a considerable departure from the traditional wire rope testers. The Magnograph has already been patented in Canada and the U.S.A.(3), and patent applications are pending in other countries.

Jan 1, 1979

By P. L. Lehoux, R. F. Lopes

"Unanticipated low recovery or extraction of gold from heap leachable are can often be attributed 10 phenomena such as non-uniform percolation (channelling) of solution through heaps, excessively slow percolation rates due to densification of ore during stacking on the pads and parasitic or competing reactions of the cyanide solution with undesirable elements or geochemical ""impurities"" in the ore. The nature and causes of these phenomena are discussed in this paper, and it is suggested that geotechnical and geochemical expertise can contribute significantly to a better understanding of the relationship between laboratory results and actual field performance of the leaching process. Recommendations are made for bench-scale metallurgical testing to be complemented by geochemical and geotechnical laboratory evaluations, to ensure more successful heap leach projects. IntroductionHeap leaching is a simple, low-cost method of recovering metals from low grade ores which has now come into widespread application particularly for gold and silver metals in the United States.The heap leach process involves percolating a lixiviant (leaching agent) solution through broken or crushed ore (Chamberlain and Pojar, 1984). In the case of gold a dilute sodium cyanide solution is used and crushed ore is ""heaped"" on specially prepared impervious pads.The potential for use of heaping leaching methods for northwestern Ontario gold deposits was discussed by Beard (1983), who suggested that the use of this extraction technique in Canada should grow significantly for low grade ores as well as for small high grade deposits which cannot justify the installation of a new mill or the use of remote custom milling facilities. Two other potential situations for lise of a heap leaching extraction method are : as a low capital cost cash generator in the opening phase of a larger new project, and as a low cost output augmenter to complement a milling operation."

Jan 1, 1989

By John F. Gartner

"New terrain maps provide information on the ground conditions in northern Ontario. This information has a relevance to mineral exploration because it assists the user in determining ground conditions prior to entering the area. The prospector, geologist, geophysicist and geochemist can then plan for the optimum use of exploration techniques best suited for theseground conditions.These terrain maps are the result of the Northern Ontario Engineering Geology Terrain Study-a program carried out by five consultants under contract to the Ontario Geological Survey of the Ministry of Natural Resources. The area mapped is 370,000 km2 and more than 100 basic data maps at a1:100,000 scale will be published.An unique terrain legend was derived to facilitate the mapping and it allows the derivation of specific user information. Examples of some of these uses are described. Introduction""Where did all the boulders come from Charlie?"", asked the student, as the prospector and his young assistant clambered through the bush. "" Why son, they were brought down here by the glacier"", the prospector replied. ""But where is the glacier now Charlie? "", persisted the young man. ""Gone back up north for more boulders son!""An old story, but one that illustrates the importance of overburden to the prospector. The use of overburden as a prospecting technique is not new. In fact, the principles have been known in the western world for at least 235 years (Shilts 1976). More recently, Dreimanis's classic work on boulder tracing (1957) and Lee's work (1971) emphasize the role of glacial geology in prospecting. In addition, papers by Smee and Sinha (1979), Averill (1978), Bereton (1978), and Gleeson and Hornbrook (1974) all describe the importance of drift in mineral exploration programs. The discovery of the copper deposit in the northern Ontario township of Currie (Thompson, 1979) is attributed in part to till prospecting methods. So the significance of the overburden is firmly established, both in the literature and in the minds of today's prospectors, geologists, geophysicists and geochemists."

Jan 1, 1981

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By Chris Brothen

The introduction of new technology in mine operations has provided real opportunities for increased efficiencies and production gains which translate into enhanced profits. Computing and network technology usage has become integrated into surface mining operations and on average these investments in technology have proven beneficial for efficiency and productivity improvements. Embracing new technologies however, does not guarantee positive results. The expectations or improvements derived through the technology must be confirmed and clarified well before implementation. Tire Pressure and Temperature Monitoring Systems are an excellent example of an existing technology that can provide full time automated performance measurements of tires operating under harsh conditions and environments. Prompt warnings or alarms signaling when a tire has exceeded operating capacities will provide savings through lowered maintenance costs and increased productivity. To truly quantify the projected savings in tire life, fuel consumption, and increased levels of production, all costs associated with the technology, both direct and indirect must be considered. Apart from the initial cost of the system implementation, ongoing maintenance and support costs must be considered as well as the costs of system integration into existing mine operations

May 1, 2008