Search Documents

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By J. Y. Hascoet, M. Marya, S. Marya

Additive manufacturing (AM) brings disruptive changes over the ways parts and products are designed, tested, qualified, assembled, inspected and marketed. With these changes come real technical challenges, therefore, concerns that mainly stem from the maturity and diversity of today’s AM processes, the feedstock materials, and the interactions between the numerous process parameters. Additive manufacturing is somewhat similar to laser and electron-beam conduction-mode welding and involves a multitude of dynamic physical events between projected feedstock and moving heat source that influence process robustness, thus deposit properties. For this paper, a simple air vent, selected for its size, thin-wall, hollow geometry and materials (specifically 316L) was made using a laser-based powder blown technology (Construction Laser Additive Direct or CLAD) and systematically inspected by optical microscopy, microhardness indentations, and electron-back-scattering diffraction (EBSD). This exemplary part is first analyzed to broadly discuss metallurgical phenomena in additive manufacturing, particularly solidification and texture development. The paper then expands to other alloys and continues correlating metallurgical observations to process parameters and part properties, also borrowing from past experience with the same 3D printing CLAD system.

Jan 1, 2014

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By James R. Wickens, David La Rosa, Robert E. McIvor, Adrian Dance

"The comminution circuit at Barrick Cortez Gold Mine uses an open circuit primary jaw crusher followed by a standard SABC grinding circuit. The grinding circuit incorporates a 26’Ø x 11’ SAG mill, an Omnicone 1560 pebble crusher and a 16’Ø x 28½’ ball mill. Both mills are driven by 4500 HP motors.In 2007, several comminution circuit studies were performed to assess circuit performance and map a course for improvement. This paper discusses the results of those studies including an analysis of mine-to-mill opportunities, grinding work index efficiency, and ball mill functional performance. Subsequently, improvements to the circuit were made to enhance operating efficiency. Specifically, improvements to the pebble crusher liner configuration, advanced process control system (expert system) and ball mill classification and ball charge are discussed. In addition, other current and future improvement opportunities are discussed.INTRODUCTIONThe Barrick Cortez property is expanding to include the new Cortez Hills open pit and underground mines. Ore from these new mines will be processed in the existing Pipeline mill facility. In conjunction with ore characterization work, performance of the comminution circuit needed to be quantified. Thus, in 2007, the comminution circuit was surveyed and opportunities for improvement identified.Figure 1 below shows the Pipeline mill flowsheet. It is a standard SABC grinding circuit using an open circuit primary jaw crusher followed by a 26’Ø x 11’ (7.92m Ø x 3.35m) SAG mill, in closed circuit with a Omnicone 1,560 pebble crusher, and a 16’Ø x 28½’ (4.88m Ø x 8.69m) ball mill. Both mills are driven by 4,500 HP (3,357 kW) motors. The SAG discharge screen aperture is 5/16” (8 mm) x 1-1/16” (27 mm) slots. Ball mill circuit classification is done with Krebs D20B cyclones."

Jan 1, 2009

By Yves-Laurent Turcotte

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d&apos;entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd&apos;hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By Brian A. Ferguson, Raynald O. Vezina, Marielle Gaudet, Raoul R. Boissonneault

"Kiena has been committed to developing a fresh management and employee relations approach since the commencement of production in 1981. The functional organizational structure encourages joint participation and commitment on the part of all employees to common goals in safety and production. The results over the last four years have been extraordinary. Kiena won the John T. Ryan Canada Trophy for 1983 for its safety record and has experienced a steadily increasing productivity through the application of new mining equipment and technology in the hands of a well-trained and motivated team of employees.This paper serves to highlight the fact that productivity, safetyand technical innovation are closely linked to employee participationand involvement which are likely to be the key to theCanadian mining industry&apos;s survival in the years ahead.This presentation follows up on an earlier unpublished paper, given at the 84th Annual Meeting of CIM in Quebec City in April, 1982, which discussed the philosophy and the planning which took place before implementation of the management and employee relations system at Kiena. This present paper reviews and expands on material given in the earlier work. IntroductionThe mining industry, which has always been considered as rather conservative in its approach, has experienced with some regularity, cyclical periods related to metal prices. These cycles, previously foreseeable to some extent have become less coherent over recent years during which time the industry has had to face fierce international competition. The issue to productivity is without doubt the major concern of the mining industry in Canada today and it represents the greatest challenge facing us during the present decade. Developments that have been made in mining technology over the precious two decades have failed to completely produce the significant advancements in higher over-all productivity that were expected."

Jan 1, 1987

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By A. K. Snelgrove

Introduction ?Concerning the inland commodities, as wel to be drawen from this land (Newfoundland) there is nothing which our East and Northe.rly countries of Europe doe yeelde, but the like also may be made in (ît) as plentifully by time and industry : Namely, rosen, pitch . . . metalls, and many moe. All which the countries will aford, and the soyle is apt to yeelde ... For besides these alreadie recounted and infinite moe, the mountains generally make shew of minerall substance : Iron very common, lead, and somewhere copper. I will not auerre of richer metalls: albeit ... more then hope may be concieued thereof. " - Narrative of Captain Hayes, second-in-command to Sir Humphrey Gilbert&apos;s Expedition, IJ83 (From Hakluyt). The investigations set forth in the following pages were made in the field in Newfoundland during the summer of 1927, and later in the laboratories and library of McGill University, and in the library of the Canadian Geological Survey at Ottawa, with the purpose of collating and adding to our knowledge of the geology of an area roughly wedge-shaped in outline, and nearly nine thousand square miles in extent, stretching across the centre of the island of Newfoundland, from the southwest to the northeast coasts. To the description of this district, which contains most of the known mineral occurrences of Newfoundland, the term mineral belt is here introduced.

Jan 1, 1928

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

By D. J. McLaws

"Recent innovations in metal smelting technology utilize continuous oxygen-enriched smelting and converting processes which are capable of producing off-gases containing up to 60% SO2 or more. Other SO2 recovery processes, involving solvent absorption and steam or vacuum regeneration, can produce off-gases with SO2 concentrations nearing 100%.Processing of these high-concentration SO2 off-gases in conventional sulfuric acid plants can cause excessively high catalyst bed temperatures and poor SO2 conversion. In order to avoid these problems, a conventional acid plant design must dilute these high SO2 process gasses with dilution air in order to provide the required oxygen to effectively convert the SO2 and provide a heat sink (via the inert N2) such that the exothermic reaction, SO2 + ½ O2 ???SO3, does not exceed the temperature limit of the catalyst or the converter vessel.MECS, Inc. (MECS) has proven that a high SO2 feed gas design can be a viable option which can increase energy recovery, reduce energy consumption and potentially reduce capital costs."

Jan 1, 2014