Search Documents

By K W. Mills, N R. P Baczynski, J Mylvaganam, D A. Prado, M F. Lee, I A. de Bruyn

"This paper presents the second part of a study of the assessment of rock stress inputs on the performance of various new mining designs at the Ok Tedi large open pit mine in Papua New Guinea. Over the years, four programs of rock stress measurement have been completed at Ok Tedi, each providing different interpretations of the in situ field stresses. Details of three of these programs and interpretations are provided in the precursor to this paper, entitled ‘Rock Stresses at Ok Tedi, Papua New Guinea’ (Lee et al, 2014).This paper explains how the various stress interpretations were utilised in the modelling of the proposed new open pit and underground mining excavations, comparing where possible their expected effects on stability. The modelled performance of three specific mine components have been discussed here as case studies, including: the below-pit drainage tunnel, as the floor of the open pit workings is mined down from 350?m above, to within just 75?m above the crown of the tunnel the stability of the 1000?m high slope of the proposed West Wall cutback the proposed sublevel open stoping extraction sequence in the Gold Coast orebody beneath the East Wall, for which only the likely ‘worst-case’ stress regime was used to assess sequencing and stability issues.The benefits of scheduling the collection of detailed rock stress measurements and other input data from a range of different sources at various stages of the projects are discussed.Alternative in situ stress models have less stability impact on open pit slopes than on underground mine excavations.CITATION:de Bruyn, I A, Baczynski, N R P, Lee, M F, Mills, K W, Mylvaganam, J, and Prado, D A, 2014. The application of rock stress inputs to stability assessments at Ok Tedi Mine, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

By J Manuel, L Lu

Increasing bed depth is one of the main options sinter plants consider to increase production, since it is an incremental improvement and less expensive compared with a new plant. To maximise the benefits of increased bed depth, correct blend design and plant operation is critical. This paper discusses test work conducted to show the effects of ore type and bed depth on sintering performance and the adjustments required in both fuel rate and lime addition depending on ore type. The differences in sinter plug macro and microstructure were also examined to show the effect of bed depth on ore assimilation and matrix formation. Finally, the benefits of blending ores to achieve the best sintering performance as bed depth increases is discussed.

Jan 1, 2007

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Coombes, R Sterk

The efficiency of the Australian and New Zealand stock exchanges relies on a fully informed market: shareholders and investors are fully and transparently informed of all material information relating to the shares. These principles of transparency and materiality are similarly core to the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code). The JORC (Joint Ore Reserves Committee) Code also includes a principle of competency to ensure that the person providing the material information for public disclosure is suitably qualified and experienced.Since its inclusion into the ASX (Australian Securities Exchange) Listing rules in 1989, the JORC Code has continually improved and evolved in attempts to meet the market’s need for competent, transparent and informed disclosure. The quality and effectiveness of Public Reporting in accordance with the JORC Code is under constant challenge: some practitioners argue there is insufficient regulation, while others argue the need for greater self-regulation.This paper contributes to that discourse by exploring how well the Reporting expectations are met, and, whether Public Reporting in accordance with the JORC Code has a material impact on share-price movement.CITATION:Sterk, R and Coombes, J, 2017. Public reporting – new standards or no standards?, in Proceedings Tenth International Mining Geology Conference 2017, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Russ, J Gediga

This paper shows an economic feasible approach to implement greenhouse gas (GHG) reduction measures into the mining and metallurgy industry (MMI). The goal to improve energy consumption is directly linked to the reduction of GHG emissions in the MMI. A baseline scenario of the considered reference system and of the respective reference year has to be designed and analysed. In a second step an analysis of the same operation using the best available technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified gaps will be reported and the potential GHG emission reductions will be put into relation to the investment, running cost and generated carbon credits of the new process technologies to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap decision-making for implementing new technology into the companyÆs business operations. The GHG reduction roadmap is developed using the marginal abatement curve approach.

Jan 1, 2009

The Wattle Dam gold mine, located near Kambalda in the Goldfi elds region of Western Australia has recently progressed to an underground operation and is now believed to be Australia's highest grade operating gold mine. At end of March 2010, the deposit had reserves of 132 000 t @ 20.8 g/t for 88 000 oz and by the end of June 2010 had produced 110 000 oz from open-pit and underground mining. The Wattle Dam main lode is characterised by very coarse gold mineralisation. Gold occurs as cm to decimetre fracture fi ll veinlets, shear surface coatings and erratic fl akey clusters. The gold has no quartz or silica association and lacks adjacent low-grade mineralisation or alteration assemblage. Geologically it appears atypical of Archaean lode gold deposits and may represent an extreme end member of the type. Definition of the lode is largely dependent on effective geological identification of the host lode zone and an understanding of the erratic distribution and grade behaviour of a high-nugget, coarse gold deposit. Dependence on assay data to defi ne the lode zone would result in the deposit being mined incorrectly and much of the deposit being left unexploited. This paper discusses the geology, coarse gold characteristics and defi nition methods which are used to successfully defi ne and mine the deposit.

Aug 1, 2010

By L Clarkson, D Williams, P Redcliffe, F van der Wal

This research presents a snapshot and insight into the trends, patterns, and common considerations identified in the current standing of real-time tailings dam monitoring practice. Based primarily on information derived from concurrent research by the author (in form of a Catalogue of Real-time Instrumentation and Monitoring Techniques for Tailings Dams), challenges and opportunities when transitioning to a real-time monitoring system are discussed. Learnings and key considerations between different monitoring approaches are explored, including themes of limitations and advantages that were observed consistently through global supplier feedback.

Jul 1, 2021

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By J E. Everett

An essential requirement of product quality control in the mining industry is to be able to reliably predict key quality properties of finished product from the data available before the extraction of the ore. From a production viewpoint, the unit of data collection is generally the input and output data set for each shift of crusher production, but could be any period where mine precrusher data can be reliably matched with product data.This paper demonstrates that linear regression models can be used to predict crush grades from blast grades, even where the crush material is blended from multiple sources or pits for each of which differing regression models might apply. The advantage of using increasingly complex regressions models to match the available data to give increasingly more powerful models is examined. The best model for any application will be a balance between required predictability, available data and the business’ tolerance for complex models.The regression modelling approach has several advantages over the more classic method of run-of-mine (ROM) crusher trials, which will be discussed.The models can use any predictor variable such as grade, geotype and in situ density provided the preextraction data set can be reliably matched with post-crusher data and is significant as a predictor. The models have been used extensively in the generation of the daily crusher plan with the aim of maintaining finished product grade. This approach has also been used associated with exploration drilling and long-term planning.It is acknowledged that there are inherent problems in fitting lump and fines grade to a linear model. However, these problems are minor when they are used for interpolation within the window spanned by the shift blend records used to produce the model. This paper discusses some of the issues limiting linear regression models in this application, and suggests methods enabling consistent models to be formulated

Sep 5, 2011

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

By E Widzyk-Capehart, C Hölck Teuber, S Steffen, V Rivero, O Fredes, E Sanchez, I Pedemonte, N Gonzalez

This paper summarises the research, development and initial application of a sensing platform that has the potential to monitor subsurface deformations, pore pressure and other variables simultaneously to gain a better understanding of rock mass behaviour. The platform is based on Networked Smart Markers (NSMs) devices, which, with their ability for wireless communication between individual sensors and the possibility of real-time data acquisition and processing, will assist in the development of predictive tools to better assess rock mass behaviour.A good opportunity to implement this technology is in the specific application of transitioning from an open pit mine to an underground caving operation. One of the key elements to maintaining the mining business during such a transition is having a good understanding of the unique geotechnical conditions of mutual influence created during the open pit to underground interaction. The knowledge acquisition will require the implementation of a robust platform for geotechnical monitoring, which could be enhanced by incorporating the NSMs. The integration of sensors within the NSMs would enable the collection of additional data about rock mass behaviour (ie caving propagation and crown pillar fracturing), which could be used to improve the management of mining operations and, specifically, allow the development of reliable predictive tools based on the data collected.CITATION:Widzyk-Capehart, E, Hölck Teuber, C, Fredes, O, Rivero, V, Sanchez, E, Pedemonte, I, Gonzalez, N and Steffen, S, 2016. Understanding rock mass behaviour through the development of an integrated sensing platform, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 275–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By S Oliver, D Willingham

"Although a resource model is central to the mineral resource value estimation process (Glacken and Snowden, 2001), creating it is a labour intensive task and in the end it is a limited representation of the actual orebody. Creating this resource model is a labour intensive task that requires inputs from geology, mining, metallurgical and commercial disciplines. It requires thousands of samples from hundreds of drill holes to be verified, grouped in geological domain, interpolated and then valued. Even after all this effort, a model is only an estimation; therefore further significant effort has gone into quantifying uncertainty in the model and subsequently risk around any value estimates derived from the model. Further risks to model quality are introduced through poorly conditioned data or incorrect assumptions.This paper proposes the application of machine learning to automate the resource model development. Machine learning is applied to the traditionally manual tasks of geological formation, domain identification and validation of the block model mineralogy. Through automation the resource estimation process can be accelerated, allowing more drill holes or a larger resource body to be processed in a given time frame, or allowing the process to be more agile to changes in input data and assumptions. A case study based on drill hole data from a Western Australian iron ore deposit (Government of Western Australia, Department of Mines and Petroleum, 2015) is used to demonstrate the application of machine learning in this process.CITATION:Oliver, S and Willingham, D, 2016. Maximise Orebody Value through the Automation of Resource Model Development Using Machine Learning, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By L O’Connor, S C. Dominy

"Geometallurgy is an important addition to any evaluation project or mining operation. As a discipline, it seeks to maximise the net present value (NPV) of an orebody while minimising technical and operational risk. It also aims to promote sustainable development and initiatives by ensuring that all stages of extraction are performed in an optimal manner from a technical, environmental and social perspective. To achieve these goals, development of innovative technologies and approaches along the entire commodity value chain are being established (Glass, 2016). Geometallurgy has been shown to increase operational stakeholder collaboration, creating an environment for knowledge sharing and improved data acquisition and interrogation, with the end result being the integration of such data into mine planning and scheduling. All of these aspects create better business optimisation, utilisation of staff and targeted and realistic key performance indicators.The mining industry faces numerous challenges including, but not limited to:declining ore gradesgeometrically and/or internally more complex depositsdeep-seated deposits, with potentially high in situ stress regimesincreasing quantities of mine waste that needs to be managed appropriatelyhigher energy, water and chemical costsprocessing of more challenging and refractory ores – textural complexitiesstricter environmental/permitting conditions – so-called ‘licence to mine’increasing demand for specialist metals (eg rare earth elements, In, Ge, Te, Rh, Se, Ga and Li)commodity market volatilitya difficult funding environment.Given these challenges, geometallurgy provides the opportunity to control or at least manage some of them.CITATION:Dominy, S C and O’Connor, L, 2016. Geometallurgy – Beyond Conception, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By Wightman D, Hoyle M. W H, Peters W. S

The Radio Hill nickel-copper deposit is located 30 km south of Karratha. It is a new discovery in an area where similar mineralization had been previously discovered at Mt. Scholl and Ruth Well. Radio Hill is the first massive Ni-Cu sulphide deposit of economic significance to have been located in the Western Pilbara.Preliminary studies indicate that the sulphide mineralization occurs within gabbros, pyroxenites and peridotites of a basic igneous cumulate layered sequence. Primary sulphides have been subsequently remobilized and concentrated as stringer and massive mineralization. This is tentatively attributed to the intrusion of a further gabbroic body.The deposit appears to be of the gabbroic association type with a Ni:Cu ratio varying from 1:4 in the outer parts of the mineralized envelope to 1:0.9 towards the central zones. In drill core observations, chalcopyrite surrounding pyrrhotite was noted in many instances. Drilling has so far delineated a body developed over a strike length of 600 m and a horizontal width of up to 25 m. The mineralization plunges 20° to the southwest with a southerly dip varying from 75° in the west to about 20° - 30° in the east.The deposit is a leaf-shaped ore zone, plunging southwest from a vertical depth of 17 m in the north to 300 m in the south. The massive sulphides occur as lensoid masses within this zone. A geological resource of up to 2.5 million tonnes at 1.5 per cent Ni and l.4 per cent Cu is indicated.The predominant sulphides are pyrrhotite, chalcopyrite and pentlandite, with significant cobalt, platinum group metals and gold. Tellurides of Pd, Bi and Pb were detected by scanning electron microprobe within the pyrrhotite and other trace metals include Zn and native tin. Massive magnetite is sometimes associated with the massive pyrrhotite intersections.A test on one composite massive sulphide sample showed that pyrrhotite is present mainly as the non-magnetic hexagonal variety and only 10 per cent is present as magnetic monoclinic pyrrhotite.The deposit has no surface expression and its identification was based mainly Oil drilling targets generated by geophysical methods. No secondary minerals have been observed in association with the primary sulphides, even though the deposit is only 17 m below surface in the northern part.

Jan 1, 1987

By P B. Schwann

The commonly accepted genetic theories of Pilbara iron ores and Woodie Woodie manganese ores have often presented them as quite unique. This apparent uniqueness is not confined to just iron and manganese, but is also seen in gold and copper deposits in Western Australia. The published material on iron and manganese ores would seem to have either a quite complicated genesis or none at all. An alternate theory for the origin of these deposits is presented which involves a protore with simple oxidation and pH controls with hydrothermal fluid sources from the diagenesis and dewatering of the underlying strata. This theory explains the distribution, thinning, cold dolerites and very high concentrations of deleterious minerals observed in these deposits. This genesis system is also related to the systems that deposit hydrothermal gold and copper in sediments in the region.This paper presents the author’s observations, sampling and mapping after several decades studying and exploring for the minerals in Australia and locations overseas. All of these theories were developed with (or in spite of!) the guidance of Mal Kneeshaw, but would never have seen the light of day without him and the others presenting here. It is not what I would call scientifically polished, and possibly deserves more detailed studies; it is, however, presented as a discussion paper.CITATION:Schwann, P B, 2015. Related genesis for iron, manganese and gold-copper ores in Western Australia, in Proceedings Iron Ore 2015, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015