Search Documents

By T Christie, A Swain

Patterns of quartz veining in epithermal gold-silver deposits at Wharekirauponga, Neavesville and Ohui in the Hauraki Goldfield, have been analysed to determine the effects of different lithologies on vein distributions. At Wharekirauponga, quartz veins are hosted in rhyolite and minor andesite, with the andesite containing slightly higher gold grades. Local basement andesite, rhyolitic tuff and silicified black shale host gold-bearing quartz veins at Neavesville. At Ohui, quartz veins are hosted in rhyolite, rhyolitic tuff and andesite. Fractal analysis was used to quantitatively describe the distribution of veining. The fractal dimension (D) of veining in silicified tuff is 0.25, moderately silicified rhyolite has D = 0.23 - 0.26, clay-altered andesite has D = 0.3, strongly silicified rhyolite has D = 0.3 - 0.39, silicified andesite has D = 0.4, and silicified black shale has D = 0.43. The D values are related to the composition of the host rock, and appear to be controlled by its competency. Hydrothermal silicification results in increased competency and higher D values. Vein thickness frequency plots for different lithologies show that andesite at Ohui, and to a much lesser degree at Wharekirauponga, contains more thick veins than rhyolite and tuff. Gold grades show a strong to fair correlation with higher vein density in three drillholes at Wharekirauponga. The fractal dimension of veining is an important control on fluid flow and gold deposition within an active epithermal system. Vein systems with higher D have a greater density of veining which would have favoured increased fluid-rock interaction. Lower D vein systems have more clustered arrays. The increased fluid-rock interaction induced by a high D vein system, when combined with a reactive host rock, results in an environment which is highly favourable for gold deposition. This situation is seen in the andesite at Wharekirauponga.

Jan 1, 1994

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the 'first-generation' methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

The use of walk-through inspections, approvals and ad hoc investigations to ensure risk is kept within acceptable levels is reaching its limits of effectiveness. Further improvement in occupational health and safety requires a systems approach, and the use of Quality Management principles is an obvious basis for this. SafeGuard, a æbest practiceÆ model health and safety management system and audit criteria based on AS/NZS ISO 9001:1994, has been produced by the Department of Mines and Energy. Quality style audits of mine and quarry health and safety systems are now being carried out by the Inspectorate.

Jan 1, 1998

By T Nassis, H M. Nel, T du Toit

Assmang Khumani Iron Ore Mine is exploiting the iron ore deposits that can be found in the Bruce-King-Mokaning farm areas in the Northern Cape, South Africa. The Bruce, King and Mokaning (Khumani) deposits are approximately 10 km south of the town Kathu, adjacent to the Sishen Mine. Assmang Limited is jointly owned and controlled by African Rainbow Minerals Limited and Assore Limited.Measurement, calculation and trending of plant throughput and chemical ore properties are critical in maintaining a successful beneficiation operation due to these values forming the basis of decision-making and thus promotion of efficient ore extraction. The Khumani management and engineering information system (MEIS) supplies information on key process parameters to an operational team and is required to do so within an optimal time frame, for maximum impact.Diverse data is put into the MEIS from multiple specialist systems, with interfaces that require manual intervention. Manual intervention is resource and time intensive to the point which limits the effect on the process and decreases the potential for value addition.Automation of interfaces decreases resource and time requirements, standardising plant wide data sources and providing the opportunity to provide specialist system data to decision-makers in a timely fashion, resulting in maximum impact on the process output.Engineering and metallurgical management systems were interfaced at Khumani Iron Mine by means of an automated table which facilitates the transfer of production data validated within the engineering system as input to the metal accounting system. This interface effectively assigns a master to each specialist data set employed for decision-making and delivers accurate process parameters to the production team within an optimal time frame, resulting in increased potential to improve beneficiation efficiency.CITATION:Nel, H M, Nassis, T and du Toit, T, 2013. The role of metallurgical and engineering information systems in the optimisation of iron ore beneficiation processes, in Proceedings Iron Ore 2013 , pp 453-458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By I Ross, C deWolfe

Block caving has been the favoured mining method for large underground hard rock mines for the last few decades. The orebody must be of a size large enough to cave and generally amenable to a caving method. Typically, these mines ranged from 15 000 to 50 000 tonnes per day (50 kt/d) and have been some of the largest and most productive underground mines in the world.Now mining companies, in the quest for improved shareholder return, are looking for higher production rates from new underground mines. Whether a ‘Greenfields’ development, or a replacement for ageing large open pit mines, minimising capital and maximising production has been a focus of project teams. These new block cave mines are what have become known as ‘super caves’. These caves range from 80 kt/d to over 150 kt/d and are being planned or constructed by several major mining companies including Codelco, Freeport-McMoRan, Newcrest and Rio Tinto.Issues facing these super caves include high initial capital costs, very long development periods and significant technical challenges. These issues tend to make it difficult to present an attractive business case for such a project.This paper will discuss some of the potential benefits as well as the technical challenges and risks of operating a mine with the block or panel caving method at these very high tonnage rates. Considerations including geotechnical conditions, development rates, panel widths and ore column heights are discussed. The risks associated with these technical challenges and potential benefits for successful approaches will also be discussed.CITATION:deWolfe, C and Ross, I, 2016. Super caves – benefits, considerations and risks, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S M. Zhang, Y X. Han, J Liu, Y J. Li

"Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time and coal addition. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67 per cent was obtained at a Fe recovery of 87.82 per cent under optimum reduction conditions where a metallisation rate of 85.82 per cent was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations.CITATION:Han, Y X, Liu, J, Li, Y J and Zhang, S M, 2013. Upgrading an Australian iron ore by reduction and efficient magnetic separation, in Proceedings Iron Ore 2013, pp 397-402 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998

By A E. Annels, I P. Hodkinson an, S P. Barr

Narrow vein systems represent an important source of gold, which have generally been exploited by small to medium sized companies. Their evaluation poses particular problems because of their grade and geological complexities. The determination of grade is arguably the most important activity in resource estimation, as it is generally grade and not tonnage that makes an orebody. This is particularly true of narrow vein-gold deposits whose resources are generally relatively small, though medium to high-grade (6 - 40+ g/t). They often display extreme grade anisotropy in all directions. Two grade populations are generally observed; 1) low, often subeconomic, background grades and 2) high-grades associated with discrete ore shoots. It is possible for gold to be distributed within the wallrocks as well as within the vein. Extremely high-grade values typify this style of mineralisation and require special consideration during grade estimation to determine if top cutting is valid or not. Estimation of both width and accumulation in 2D on vertical longitudinal projections or inclined planes have historically been used to evaluate narrow veins. Resource estimates based on traditional 2D methods is still widespread, but has in some cases been replaced by computer-based 3D modelling. Grade estimation methods are well-known, ranging from classical to geostatistical. Historically, classical methods such as inverse distance weighting have been used, though geostatistical indicator kriging methods are sometimes applicable. Geostatistical studies are driven by the production of reliable variograms, which in narrow gold veins is often problematic. It is generally difficult to define resources from drillhole intersections beyond the inferred and indicated categories with any confidence. In the majority of cases underground development is required to define measured resources and ore reserves. Trial mining/bulk sampling is often used to test estimated grades and also provides important data on ground conditions and the parameters relating to the proposed mining method required for ore reserve definition. Regular reconciliation should be undertaken between the estimated stope grades, grades indicated from stope/truck sampling and grades realised in the mill in order to determine whether correct evaluation strategies are being applied. The important feature of narrow vein-gold deposits is their strong geological controls; in response to this, geologists must understand the geology as best as possible.

Jan 1, 1999

By A G. Cuison, B V. Andam

Three well-known copper and gold deposits in northern Luzon, Philippines are located in the Mankayan Mineral District. These are the Lepanto Copper-Gold Deposit, the Far Southeast Porphyry Copper Deposit and the newly discovered Victoria Gold Deposit. The latter discovery led LCMC to shift from a predominantly copper mine to a gold mine. The pre-Eocene Lepanto basement andesite and the middle Miocene Balili volcaniclastic sequence underlie the Mankayan Mineral District. They are intruded by tonalitic to gabbroic Bagon Intrusive followed by diorite-quartz diorite intrusions. Diatreme emplacement of late Miocene-early Pliocene Imbanguila dacite pyroclastics and porphyries took place much later. Faults in the district mostly form a conjugate fracture pattern dominated by north and northwest trending shears, east-west trending extensional fractures and few north-south trending fissures. Victoria is an epithermal gold-base metal rich quartz vein deposit. The veins occur along tensional structures and it is common to observe crustiform and banded features among the sulphides and gangue minerals. It is an open space infilling type of mineralisation. The Victoria vein systems are divided into zones based on continuity. In each zone are major veins and associated spits. Dacite pyroclastics and porphyries predominantly host the major veins with a few narrow veins hosted by the Balili volcaniclastics and the Lepanto metavolcanics. The veins generally trend east-northeast with 75 - 80 dips towards the south. The longest vein can be traced fairly continuously for a horizontal distance of about 600 metres. The vertical persistence of major veins exposed on three level drives has a range of 150 metres and can reach as much as 400 metres based on drill hole intercepts. The vein widths vary from two to eight metres. Right lateral movements of either the NW or NE shear faults could have produced the east trending tensional fractures. The development of ore shoot patterns was recognised and has been helpful to the mining operations. Cymoid loops with defined pinch and swell features are noted both laterally and vertically. Complementing the structural pattern is the distribution of gold values along veins where lateral and vertical continuity is also observed. Gold is associated with quartz, sphalerite, galena and chalcopyrite. In relatively high gold zones, the abundant sulphides are sphalerite and galena. In relatively high copper zones, there is an abundance of chalcopyrite and tetrahedrite. Galena is always associated with sphalerite but less in abundance. Chalcopyrite occurs either as separate bands from or associated with sphalerite-galena. Chalcopyrite and tetrahedrite appears contemporaneous with sphalerite and galena but in some portions the former cuts the latter sulphides. The predominant gangue minerals are quartz, carbonates and gypsum. Rhodochrosite is the predominant carbonate gangue. Few sulphides are found in the carbonates. Gypsum (anhydrite) is found cross-cutting early mineralisation. It carries very few sulphides. The alteration halos around veins are relatively narrow. In an outward sequence, the silicic alteration occurs very near the veins, followed by sericitic-argillic alteration then to propylitic zones. It is also common to observe veins bounded by propylitic alteration. Preliminary paragenetic studies show apparent three stages of mineralisation, the early-quartz (-gold) stage followed by a carbonate stage and a late-gypsum stage. The abundance of base metals relatively decreases towards the gypsum stage. The Victoria gold deposit could have some genetic associations with the Lepanto Cu-Au deposit and probably indirectly with the FSE porphyry system. It is relatively apparent that the Victoria quartz-gold-base metal veins could have occurred similarly as the quartz-gold roots overprinting the Lepanto enargite mineralisation. This overprinting signifies the waning stages of the entire hydrothermal system.

Jan 1, 1999

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

Physical/Chemical Treatment of Mercury-Contaminated Wastes from Former Chlorine-Alkali Electrolysis Plants - Application of Flotation Technologies in Soil Washing Plants

Sep 13, 2010

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

High-sulphidation (HS) gold, silver and/or copper deposits are generated in both the epithermal and the upper parts of the underlying porphyry environments over vertical intervals of up to 2 km. The HS deposits are generated in advanced argillic lithocaps, which are products of the absorption of acidic magmatic volatiles by voluminous groundwater systems. Mineralisation styles in HS systems reflect depth of formation as well as the interplay between structural, lithological and hydrothermal parameters. The deep parts of HS systems, at depths of >1000 m, are typified by disseminated copper¦gold mineralisation comprising digenite, chalcocite and covellite in pervasive advanced argillic as well as underlying sericitic alteration. In highly telescoped systems, such mineralisation may overprint porphyry stocks and associated quartz-veinlet stockworks. Intermediate levels of HS systems commonly contain fault-controlled copper-gold mineralisation, typically as enargite in bodies of vuggy residual quartz, silicification and/or massive pyritic sulphide. The shallow parts of HS systems, at depths of The exploration focus is on four principal HS mineralisation styles:copper (eg Chuquicamata, Monywa) or copper-gold (Wafi) in the deep porphyry-hosted parts of systems preferably, in the case of the latter, where supergene oxidation is limited and, hence, flotation may be used for metal recovery; copper¦gold-bearing replacement mantos and pipes hosted by carbonate wallrocks in the deep parts of systems (eg Bisbee); high-grade gold in late-stage veins or hydrothermal breccias that overprint the intermediate to shallow levels of systems (eg El Indio, Goldfield); and large, bulk-mineable gold deposits in the shallow parts of systems that were subjected to supergene oxidation, thereby permitting heap-leach treatment (eg Yanacocha, Pierina). To these preferred HS styles may be added the low-sulphidation vein or disseminated gold¦silver mineralisation that is commonplace alongside many HS systems (eg Victoria at Lepanto).

Jan 1, 1999

By A J. Falconer

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are determined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF). Has a value superior to that of soluble iron when relating raw sand grade calculated by triangulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CF), is shown to merely reflect TMF and offers no additional information for assessment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

By Waugh D. M

investigations have been undertaken into the flow characteristics of mineral slurries from a number of Australian metallurgical plants including Mount Isa Mines Ltd., North Broken Hill Ltd., and Broken Hill South Ltd. Experimental equipment installed for this work included facilities for continuous recording of flow rate and pressure drop and detection of sedimentation.Although the method has subsequently been described in published literature, it is believed that the investigations included the original application of a method for correlation of the flow rate and pressure drop data. This method depends on solving by graphical methods the values of the constants k, and c in the relationship EQUATION 1 where D is pipe diameter; ?P, pressure drop; L, length; and V, mean linear velocity. Discussion of this correlation also reveals why sedimentation velocity does not necessarily vary greatly with pipe diameter.INTRODUCTIONIn order to design pumps and pipeline installations for a Newtonian fluid, measurements of the fluid's density and viscosity in any of a number of instruments are sufficient. Substitution of these values in well known equations to calculate Reynolds numbers and subsequent correlation to determine friction factors are all that is required for engineering specification.As a result of work during the last decade, particularly that of Metzner and Reed (1955) and Dodge and Metzner (1959), it is now possible to design for homogeneous non-Newtonian fluids using relatively simple instrumental measurements.These methods can sometimes be applied to thick slurries which behave as if homogeneous. However, for the...

Jan 1, 1965

By J Coward, S Bulatovic

There are currently two operators producing oil from the surface-mineable portions of AlbertaÆs oil sands (Syncrude Canada Ltd and Suncor Inc) and two other companies are proposing to enter the industry (Albian Sands Energy Inc in 2002 and True North Energy LP in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of TiO2 and approximately 80 000 tonnes per year of zircon. This represents approximately six per cent of the worldÆs TiO2 consumption and approximately nine per cent of the worldÆs zircon production. With the commissioning of plants by Albian and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in AlbertaÆs oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widely-held suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers:the bitumen coating on the sand grains; secondary mineralisation such as pyrite, siderite and calcite; and a high proportion of aluminosilicates (approximately 25 per cent) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier; the pyrite can be removed by flotation; and the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

Jan 1, 2001

ThePike River coal field is located between 700 and 1000 m above sea level on the West Coast of the South Island. The area contains a resource of some 60 million tonnes of coal in a single coal seam and is part of the Paparoa mountain range that receives between 6.0 and 6.5 m of rainfall per annum. The area has been isolated and has received no on the coal plateau but has been extensively logged in the lower 3.5 km of Pike Stream. The PRCC development proposal recognises this and calls for an environmentally benign development that includes underground development of this resource. The coalfield abuts and is partly overlain by the Paparoa National Park. The underground development will enable a number of environmental goals to be readily achieved: it will be out of sight of the public,it will not impact the national park,noise will be mostly absent,there will be absolute minimal disturbance to the land surface,coal will be transported from the mine to a dewatering complex on PRCC land in a slurry pipeline thus obviating the need for trucks and noise in Pike Stream valley,all water draining from the mine will be collected, treated if required to consent standards and discharged from a single point,the road into the area will allow for an effective predator control programme to be undertaken enhancing native bird life,an environment suitable for the reintroduction of Whio (Blue Duck) will be created, andthe net effect of the mine development on the environment will be positive.

Jan 1, 2003

By D Craw, L Cox, R J. Norris

The Rise and Shine Shear Zone is a mineralised low-angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. The zone is commonly believed to be similar to the actively mined Macraes deposit. The Rise and Shine Shear Zone occurs in the immediate footwall of the Thomsons Gorge Fault, a regional scale Cretaceous normal fault that juxtaposes chlorite zone schist against biotite zone schist. Most mineralised rocks are deformed and record a progression from early stages of semiductile deformation to more brittle cataclasis. Folds in mineralised rocks trend northwards. The mineralised schist is hydrothermally altered with variable silicification, sericitisation, chloritisation, replacement of titanite by rutile and carbonate alteration. Gold is associated with pyrite and arsenopyrite and occurs in both ductile and brittle microstructures. Sheared and mineralised schist is cut by north-striking fault zones which host mineralised quartz veins. Veins in the shear zone contain hydrothermal albite. Trace element analyses show enrichment in As, U, Th and rare earth elements. Many of the above features are similar to Macraes deposit, but there are important differences. In particular, the Macraes deposit is hosted in lower grade rocks and truncated beneath by a normal fault, Macraes has no U or Th enrichment, Macraes veins have no albite and folds at Macraes trend NW-W. Rise and Shine mineralised rocks have no Cr enrichment and no hydrothermal graphite.

Jan 1, 2005