Search Documents

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one. if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate. l7,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Gaudin. A. M., S. C. Sun

THIS paper presents the results of a study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresis1-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation [z = 47ruu(300)$ Kx] in which z is the zeta potential expressed in in volts, u the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas,6 The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mix-

Jan 1, 1946

By A. L. Marshall, F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C.oin a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. APPARATUS AND TECHNIQUE The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 0800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard' glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not 'a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by

Jan 1, 1944

By J. W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles. as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain. GEOLOGY The rocks of Jumbo Mountain comprise a series of folded Tertiary sediments forming a belt one half to three quarters of a mile wide, trending northwest about parallel to the strike of the beds. This belt is sandwiched between two extensive in-trusives—gabbro on the northeast and quartz dio-rite on the southwest—and has been intruded by dikes of fresh and serpentinized dunite. Shear zones follow many of the dunite-sedimentary rock contacts, and in these the nickel mineralization is concentrated. A few transverse faults offset the sediments and ultrabasics. Sedimentary Rocks: Two kinds of quartzite make up the greater part of the sedimentary section. One is dark purplish gray, very fine-grained, and thin-bedded; the other is light gray to white, medium-grained, and well-bedded. Locally the light-colored quart lites contain grit and conglomerate horizons, rich in pebbles of white chert and very fine-grained quartzite. Intercalations of dark argillites near the summit of the mountain give many of the cliffs a striking banded appearance. Dark gray to black, aphanitic, thin-bedded argillites occur throughout the entire sedimentary belt. Beds vary from a few inches to a few tens of feet thick and some, near the summit, contain numerous fossile (willow?) leaves. Only the thicker beds were mapped. The sediments are quite fresh on the northeastern side of the belt and become more metamorphosed (hornfelsed) toward the southwestern side. Brown biotite is present in the metasediments in increasing amounts as the quartz diorite is approached. Near the intrusion, porphyroblasts of plagioclase, up to 1 in. across, testify to the soaking of sedimentary rocks by solutions emanating from the quartz diorite. Most of the sediments mapped lie along the southwestern limb of an anticline, the axis of which follows the crest of the mountain and plunges at a low angle to the northwest.

Jan 1, 1961

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970

By Charles E. Wait

It is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony—stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities ; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920