Search Documents

By A. Tonejc, A. Bonefacic

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26o +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr , Ni , Sb , Mn , P , Sn , and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By John S. Alexander

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By A. W. Gauger

SMELTING of iron ore, manufacture of steel, and the fabrication of ferrous metal products are all processes that require energy. Charcoal was adequate, to supply this energy for the relatively simple processes of the early iron-masters. In the fourth decade of the nineteenth century, anthracite and bituminous coal and later coke supplanted charcoal for the smelting of iron. So far as the chemical phases of the process were concerned, charcoal was an ideal iron-furnace fuel. It had practically no sulphur, and its ash, besides being low in quantity, consisted chiefly of lime and alkalies, thus supplying a part of the flux required for smelting the ore. The ash of coal and coke on the other hand, being largely silica, had itself to be fluxed with bases added to the charge. Physically, however, coke proved to have many advantages over charcoal, which could not be used in the furnaces of today. The chief reason, however, for the change from charcoal to coke was the impossibility of maintaining an adequate wood supply.

Jan 1, 1941

By W. B. Plank, A. C. Callen

WAR and normalcy do not walk hand in hand, whether it be in industry, the educational field, or in the daily lives of individuals. Schools and departments offering curricula in mineral engineering have been seriously disrupted, beginning with 1942 and reaching a low during 1944. Selective Service regulations and voluntary enlistments have effectually stopped the flow of college-trained men into the mineral industry, and the flow into the colleges is little more than a dribble. The year just closed has been a most serious one for our institutions. Until March many of our faculties had been kept reasonably intact because of the large training programs of the Army and Navy. Although the number of

Jan 1, 1945

Jan 1, 1899

By AIME AIME

APROXIMATELY one third of the world's iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

By Hugh M. Roberts

In the spring of 1915, then a 30-year old geologist in the employ of the E. J. Longyear Co., of Minneapolis, Minn., I accompanied prospectors to ex- amine outcrops of supposed nickel ore situated a mile or two in from the shore of a lake in the Kenora district of northwestern Ontario. The deposit proved to be bog iron ore containing traces of nickel. We were stormbound there for three days, a circumstance which gave rise to a tale that was told at our fire one night. It seems that Sandy and Jock, two prospectors, were crossing the bay of a large lake in a canoe. They were bucking headwinds; the waves grew higher. Jock called out from the stern, "Sandy, can ye na pray a little." Sandy pressed his knees a little closer into the bow and, between strokes of his paddle, sought for words, which came haltingly, "Save us this time . . . Oh Lord . . . and we promise . . ." when Jock, peering through the spray sang out, "I would na commit yourself, Sandy, I think I see lond ahead."

Jan 1, 1965

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

By F. R. Hensel

PURE silver and silver-lead alloys have been studied as to their suitability for bearings.1-8 A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materials.† The silver-rich end of the diagram as reported in the literature9-11 was found to be sketchy and it was necessary to carry out considerable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. TEST MATERIALS In the beginning of the work, only fused alloys were investigated. Later, research [TABLE I. Composition of Fused Silver thallium Alloys Tested for Antifriction Properties PERCENTAGE ALLOY No.OF THALLIUM 15330.48 153406 231 HT2.04 2312.10 232 HT3.83Balance 2324.07Silver 233 HT5.86 2336.38 2349.84 234 HT10.07] was carried out on electroplating methods and diffusion processes. In preparing the fused alloys, care was taken to exhaust the toxic fumes caused by the thallium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in. diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr2O7, 8 c.c. H2SO4, and 100 c.c. H2O. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C. show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475°C. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not result in complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1945

By H. Y. Yancey, B. M. Bird

One of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practice for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical dancing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1930

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth's crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental's new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By K. E. Brown, F. W. Jessen

By utilizing an 8,000-ft experimental field well equipped with 10 gas-lift valves and 10 Maihak pressure recorders, gas-lift tests were conducted with port sizes ranging from 5/16 through I in. The well was equipped to provide accurate means of measuring surface pressures, temperatures, quantity of injection gas and fluid production. The tests were conducted in 2%-in. OD tubing, and the well was making 95 per cent water. A complete evaluation of gas-lift-valve port sizes shows the relationship of per cent recovery, gas-liquid ratios, minimum pressure created at the operating valve and horsepower requirements for each port. The length of time necessary for the fluid in the tubing to reach equilib.rium conditions after each cycle was recorded. Fallback of fluid at depths of 477, 969, 1,685, 2,493 and 4,290 ft was noted. For each port size, pressure loads of 2.50, 300, 350, 400 and 450 psi were lifted with a valve operating at approximately 550 psi at 6,000 ft. Gas-liquid ratios for each load were varied from excess gas to a gas volume per cycle whereby the load failed to reach the surface. Numerous curves are presented in evaluating the accumulated dara. The results show a 1-in. port to be the most efficient under all conditions. The production of intermittent liquid slugs against different-sized surface chokes was evaluated. These tests were conducted from a 7/16-in. ported valve at 4,072 ft. Tests indicate that, when possible, a %-in. in diameter choke or larger should be used at the surface. In the past few years most of the advancement in gas-lift operations has been made in continuous-flow operations. Yet, it is estimated that at least 70 per cent of the wells on gas lift in the United States are of the intermittent type. Since the term "slug flow" is sometimes used in both intermittent- and continuous-flow operations, it would be well to distinguish between the two types of flow. Continuous-flow gas lift is defined as a method whereby the fluids are produced at a continuous rate at the surface. This generally requires a continuous injection of gas through a surface choke; however, various other control devices sometimes are installed to eliminate freezing, to shut-off gas during natural flow periods, etc. The actual flow of fluids in the tubing may be of the slug type (one of many flow patterns known to exist in continuous flow). Intermittent flow is defined as a method of gas lift whereby the liquid is produced in separate piston-type slugs. Perhaps this type of flow could best be thought of as a ballistic-type flow where the liquid leaves bottom as a piston, propelled by a slug of expanding gas. Gas generally is injected through some type of control at the surface at predetermined intervals. However, the valve may have characteristics whereby gas can be injected through a small choke and still result in a ballistic-type flow. The purpose of the experimental work was to evaluate the most efficient port size to be used on the operating valve for the ballistic type of lift and, in addition, to establish the importance of utilizing a surface choke large enough to allow slugs to be produced without detrimental effects. This work is part of a compre- hensive study of both intermittent-and continuous-flow gas lift, representing a joint project conducted by the Ohio Oil Co., the Sun Oil Co., Otis Engineering Corp, and The U. of Texas. The problem of evaluating port sizes has been given little previous attention. Some work undoubtedly has been done which has not been published to date. Some tests were conducted when the wireline, mechanically-opened valve (Nixon) first came on the market. This valve was capable of utilizing full tubing area as its port size. It is known that this was a very efficient valve, but to the authors' knowledge the results of tests have never been published. EXPERIMENTAL EQUIPMENT These tests were conducted on an actual field well, the Ohio-Sun Unit Well No. 2-E, in the North Markham-North Bay City field, Matagorda County, Tex. The well incorporated 23/8-in. OD tubing and produced 95 per cent water. Since the running of equipment was to be quite elaborate and expensive, a well was selected in which both intermittent- and continuous-flow tests could be conducted. This particular well was capable of producing in excess of 1,000 B/D of liquid (95 per cent salt water), yet with a 3/64-in. in diameter bottom-hole choke, production was controlled to 82 B/D. Most of the intermittent tests were conducted at this low rate. Figs. 1 and 2 show all the surface and down-hole equipment. As can be seen, every attempt was made to insure that ample equipment was available for reliable testing procedures. Fig. 1 shows the surface testing equipment. The input gas was controlled first by a regulator, then

By L. S. Kolbert, C. H. Baab

Introduction In June 1981, the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the US coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent." With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. Major Features and Benefits of Nuclear Measurement and Analysis Systems There are many features and benefits of nuclear instrumentation. The major benefit is that nuclear instrumentation is non-contacting. The measuring heads do not contact the process materials. This enables measurements of corrosive, abrasive, or high temperature materials with no loss of performance, reliability, or useful life. Also, there are no moving parts to wear or be fouled by dust or corrosion. Installation is simple and inexpensive. For instance, density gauges are simply clamped onto existing pipe runs. Weigh scales and level switches usually require nothing more than welding brackets to customers' equipment. Once installed, routine maintenance can be performed without interrupting the process. Thus, nuclear instrumentation is highly reliable and easily installed and maintained. The operating life of the instrumentation is virtually unlimited. Principle of Operation Nuclear belt weigh scales, point level switches and density gauges all operate on the gamma-ray transmission principle. A beam of gamma radiation from a radioisotopic source is projected through the process material either on a belt, in a vessel, or in a pipe. Opposite the source is a radiation detector whose electrical output is proportional to the intensity of the radiation it absorbs. Gamma radiation is part of the same electromagnetic spectrum that encompasses light, infrared, and x-rays. In many respects, gamma radiation behaves much like light. However, it is far more penetrating and can be transmitted through considerable thickness of materials that are opaque to visible light, e.g., several inches of steel. Types of Nuclear Instrumentation in Coal Preparation Plants There are four types of nuclear instrumentation presently being employed in coal preparation plants. They are: •Belt Weigh Scales •Point Level Switches •Density Gauges •Coal Analysis Equipment. Each type of instrumentation has a number of potential applications within the plant. What follows is a discussion of three different types of devices and their applications. Weigh Scales In coal preparation plants, weighing instruments are used for measuring material throughput, totalized weight, and batch weight on conveyor belts and other transport equipment. They are also used on drag chain conveyors, vibrating conveyors, and screw conveyors. Weighing is important for receiving the run-of-mine coal, controlling mass flow, scheduling production, and loading and shipping the washed coal to market. There are two basic types of weighing instruments: gravimetric and nongravimetric devices. Gravimetric devices are units which measure the pull of gravity on the material being weighed. Nongravimetric devices are not dependent on the force of gravity on the sample. Nuclear weigh scales are the most prevalent nongravimetric devices used. The nuclear weigh scale works on the same basic principle as other nuclear gauges. The greater the quantity of material placed in the path of a radiation beam, the more radiation will be absorbed by the material. In weigh scales, Cesium 137 source is generally placed above the moving stream of material so that the radiation is directed through the material. An ion chamber radiation detector is on the opposite side of the material. The radiation passing to the detector generates a signal which is inversely proportional to the weight of the material present. This signal is amplified and integrated with the speed of the process flow yielding the weight. The weight is indicated and can be totalized for throughput, batch control, etc. In conclusion, radiation weighing methods have become well established in the coal preparation industry throughout the world. As mentioned before, this device finds its most

Jan 1, 1985

By E. Topanelian

In recent years considerable progress has been made in the development and application of mathematical techniques for the solution of certain problems involving economic "strategies". Such a problem might involve, for example, the scheduling of shipments of a commodity from a number of sources to a number of destinations. The object would be to schedule the shipments in a manner so as to satisfy the destination requirements and at the same time minimize the transportation costs. The solution to such a problem is not necessarily intuitively obvious. The "obvious" solution is frequently far from optimum. If the shipments are to be made from, for example, only two sources to four destinations, the optimum schedule is readily found. However, if shipments are to be made from, say, 10 sources to several hundred destinations, even a competent and experienced scheduler may spend considerable time in finding a reasonable answer. Even then he is not sure that he has the optimum solution. Furthermore, he has no way of knowing how far from optimum the answer is. Consequently, he does not know whether he should accept this solution or seek a better one. Prior to the advent of large high-speed digital computers, little more could be done with such problems because of their great size and multiplicity of possible solutions. A problem involving 20 sources and 50 destinations would require choosing, from a very large number of possible combinations, the optimum combination of 1,000 variables. The best one could do was to utilize intuition, extrapolation from past experience, and other non-exact approaches. With a high-speed computer, however, such problems can be solved providing a reasonable computational procedure (or algorithm) can be utilized. The purpose of this paper is to describe such a procedure (linear programming) and to apply this procedure to a production scheduling problem. THE RESERVOIR PROBLEM A simple reservoir model is used throughout this analysis to illustrate the use of linear programming. Even the simplest reservoir behavior problem is nonlinear in both space and time, but if the geometry is fixed for a particular study and the time variable is quantized, the resultant system may be described by linear constraints on the variable production rates. Crude oil is available from five separate sources and is delivered to a pipeline. Sources 1, 2, 3 and 4 are ideal reservoirs and therefore are subjected to reservoir flow restrictions. Source 5 is labeled "Outside Source" and crude oil from this source is assumed to be available in unlimited quantities without considering reservoir conditions. The general problem is to determine the schedule of crude oil production from five sources which, over an eight-year period and subject to certain restrictions, will result in maximum profit. "Profit" is defined to encompass all economic factors and expenses involved in producing and selling crude oil to a pipeline facility. Such economic factors are lumped to the extent that the term represents the dollars profit from one barrel of crude oil from any of the five sources entering the pipeline system. Table 1 presents the assumed profit per barrel for oil from any of the five sources over each of the four time periods. In this chart the eight years is broken into four equal intervals of two years. The selection of four time periods of two years each and the values representing the potential profit are completely arbitrary selections for the purpose of illustrating this idealized reservoir problem. In any practical application of this work a careful economic study would have to be made in order to estimate potential unit profits for time periods as far in the future as eight years. In this particular study it is assumed that all of the potential unit profits (C) are known and fixed before the production schedule is attempted. For each reservoir arbitrary values are assigned for