Search Documents

By Ricardo Thomé da Cruz

O conhecimento sobre o comportamento do revestimento refratário dolomítico durante a etapa do refino de aço é fundamental para se atender às exigências técnicas de qualidade e o aumento da produção de aço. É particularmente importante que os mecanismos de corrosão dos refratários dolomíticos sejam bem compreendidos, principalmente, em operações de exceção, nas quais as exigências metalúrgicas causem forte dano ao revestimento, prejudicando não somente o desempenho do mesmo, mas também gerando um risco à segurança operacional. Este trabalho visa à caracterização técnica da camada protetora (coating) de silicato dicálcico (C2S), a qual se origina da reação entre as escórias silicosas e os refratários dolomíticos. As amostras de coating foram caracterizadas quanto à composição química, fases formadas e microestrutura. Estudou-se uma panela retirada de operação, por dano aos refratários, retirando-se amostras de diferentes regiões. Em duas amostras, juntamente com o C2S e o periclásio, foi observado à presença de fases à base de silicato de baixa fusibilidade como a cuspidina, indicando que o coating foi atacado por uma escória com elevado teor de fluorita.

Jul 30, 2018

By Thiago Pinto Wandekoken

A aciaria elétrica da Votorantim Siderurgia em Resende, possui um FEA de capacidade de 100 t, transformador de 100+20 MVa, equipado com 05 injetores convencionais de oxigênio e 03 injetores convencionais de carbono. Em função do elevado aporte de energia química e elétrica inserida no processo os painéis refrigerados, e demais equipamentos localizados em determinadas regiões do FEA, são termicamente mais solicitados e requerem maior atenção e rigor do sistema de manutenção preventiva, a fim de evitar interrupções operacionais do processo. Através da análise de dados históricos, detectou-se que a região do FEA de maior criticidade e intervenções de manutenção era o painel refrigerado P-10. As tecnologias Double Side e Protect Block foram instaladas em substituição ao painel refrigerado P-10 com o objetivo de aumentar a confiabilidade operacional do FEA, reduzir os riscos de acidentes operacionais, aumentar a disponibilidade dos equipamentos nesta posição, reduzir o número de intervenções de manutenção (preventiva e corretiva), reduzir os custos de manutenção (preventiva e corretiva) e consequentemente reduzir o power off do FEA.

Aug 16, 2017

By Luciano Henrique Andrade de Resende, Maria Rita Oliveira Rebouças

O processo de Monitoramento Controles, realizado pela área de Governança, Riscos e Compliance, requer preparação e verificação de um grande volume de dados. Isso feito de forma manual e com a necessidade de cruzar dados de diferentes fontes, torna o processo bastante complexo, impactando diretamente na periodicidade e acurácia dos testes. O objetivo de trabalho era prover uma ferramenta e uma metodologia que fosse capaz de automatizar esse processo, tornando-o contínuo e possibilitando análise de uma grande massa de dados, proveniente de diferentes fontes e com uma saída padronizada. Após análise de ferramentas de mercado e a realização de provas de conceito, foi definida a ferramenta e modelo de trabalho a ser aplicado. O resultado foi a implantação de um processo de Monitoramento Contínuo de Controles (MCC) que traz: ganho de produtividade, ao permitir que testes sejam executados de forma automática; ganho de eficiência, por permitir realizar o teste em toda a base de dados, sem necessidade de amostra; aumento na assertividade, por reduzir probabilidade de erro humano provenientes de atividades manuais; além de retorno financeiro e mitigação de riscos.

Oct 1, 2019

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By José Marcelino dos Reis

Com o empobrecimento das jazidas minerais, os novos projetos industriais e as expansões das atuais usinas de tratamento de minério de ferro, em sua grande maioria, têm sido concebidos/ adaptados para processar itabiritos pobres para produção de pellet feed. Neste contexto, a otimização dos processos já existentes e/ou a implantação de projetos mais eficazes, são medidas fundamentais para a redução do teor de ferro no rejeito; consequentemente, maximiza-se a produção e a vida útil da jazida, além de reduzir os custos operacionais. O processo de flotação reversa de minério de ferro da usina de concentração de Brucutu responde por expressiva parcela de produção, sendo constituído por quatro estágios de concentração: rougher, cleaner, recleaner e scavenger. O concentrado final é produzido no estágio recleaner e o rejeito final no estágio scavenger, cujo teor médio atual é de 18% Fe. Objetivando reduzir o teor de Fe no rejeito scavenger da flotação para teores próximos a 10%, foi realizada uma série de testes exploratórios em bancada em diferentes faixas de pH, com adição de soda caustica e/ou amido gelatinizado. Os resultados obtidos em escala de bancada se mostraram bastante satisfatórios apresentando considerável ganho de recuperação mássica/ metalúrgica, o que motivou a realização de um projeto para viabilizar a implementação desta proposta.

Aug 1, 2018

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Ernesto Gustavo Maffia

En la actualidad, el moldeo por inyección es una tecnología muy utilizada en el procesamiento del plástico pues permite fabricar formas geométricas complejas. Para fabricar los moldes se utiliza ampliamente la aleación C17200 (Cu-2%Be), pero están en desarrollo algunas alternativas con aleaciones base cobre libres de berilio, que tienen valores de dureza por encima de los 30 Rockwell C y buena conductividad. Las aleaciones base de cobre, tipo CuNiSiCr son las más adecuadas como reemplazo. El siguiente trabajo trata del estudio y desarrollo del proceso de fabricación, por fusión, colado y conformado, de una aleación tipo CuNiSiCr de alta dureza y buena conductividad para ser utilizada en la fabricación de moldes de inyección para la industria del plástico. Los resultados preliminares de esta investigación demuestran que a través del aumento sistemático en el contenido de níquel y silicio se consigue un aumento de la dureza (>32 Rockwell C) y una aceptable conductividad eléctrica (˜25%IACS). El fenómeno segregación interfiere fuertemente en los tratamientos termomecánicos, pues se forma una segunda fase interdendrítica, de características frágiles, que genera fracturas en el conformado. Los resultados demuestran que la aplicación del recocido total y control de la temperatura durante la forja minimizan este problema.

Aug 7, 2018

By Thiago Pinto Silva

A Usiminas implementou dois ensaios para caracterização de minérios de ferro na sinterização, intitulados assimilação e penetração de fase líquida. O primeiro tem como objetivo avaliar as fases mineralógicas, a formação de poros e a resistência mecânica de partículas nucleantes e aderentes por meio da reação do minério com o calcário. O segundo objetiva medir o comprimento da penetração da fase líquida formada entre a calcioferrita e o minério. No presente trabalho, são descritas as principais características e potencialidades desses novos testes, os quais foram utilizados para a avaliação do comportamento metalúrgico de seis minérios distintos. Os resultados obtidos de assimilação e de penetração da fase líquida foram comparados com as características mineralógicas e químicas dos minérios, sendo observada uma boa correlação entre essas características e os resultados dos novos testes. Verificou-se também que a análise tradicional do minério não é suficiente para estimar seu comportamento metalúrgico na sinterização, o que reforça a importância da utilização dos novos testes implementados. Além disso, permitem avaliar o comportamento dos minérios em altas temperaturas, auxiliando na escolha da carga de minérios mais adequada para a sinterização.

Aug 1, 2018

By Danilson Gonçalves de Melo e Silva

O balanço de energia realizado em um forno de aquecimento de tarugos apresentou rendimento de 53%. A maior perda energética estava relacionada ao sistema de refrigeração dos skids, cujo valor calculado foi de 18%. Objetivando minimizar tais perdas, estudou-se a utilização de um novo tipo de revestimento refratário para esta região. O fabricante de refratários apresentou uma estimativa de ganho de 62%. Desta forma, a VBR planejou um teste para validar a eficiência do refratário proposto. Neste teste, o produto foi instalado em uma viga auxiliar. Esta viga foi instrumentada, e foram registrados dados de vazão, pressão e temperatura do fluido de refrigeração (água). Objetivando comparar estes valores com o material convencional anteriormente instalado, outra viga com as mesmas características (dimensões e posição no forno) também foi instrumentada. Posteriormente, foram feitos os balanços de energia em cada viga para quantificação das perdas de energia térmica. Os resultados encontrados mostram uma redução de 92% da perda térmica relacionada ao sistema de refrigeração dos skids. Considerando a eficiência do forno de 53% e a redução de 92% da perda térmica, estima-se uma economia de R$ 1.200.000 por ano.

Sep 25, 2017

By Carlos Alberto Perim

Devido à obstrução no distribuidor, os aços ultra baixo carbono estabilizados ao titânio apresentavam baixo sequencial de lingotamento na ArcelorMittal Tubarão (AMT). Foram identificadas práticas utilizadas na redução de obstrução nestes aços, que foram adotadas para a produção na AMT. Uma das práticas foi estabelecer uma relação entre alumínio e titânio com menor propensão à formação de compostos de alumina e óxido de titânio que se aglomeram na região da válvula superior do distribuidor. Também foram introduzidas melhorias no processo visando a melhorar a condição de fluxo na região próxima da saída do aço no distribuidor. Neste projeto, um aço UBC de maior volume de produção foi escolhido e novas práticas foram adotadas para sua produção. Amostras de aço foram retiradas de corridas produzidas nesta condição e foram enviadas para análise na ArcelorMittal Research USA. Os resultados mostraram melhorias nos índices de qualidade tanto em laminados a quente como em laminados a frio. Neste trabalho será apresentado um resumo das ações adotadas na AMT, que resultaram em um aumento do sequencial médio de distribuidor, permitindo atingir um máximo de 18 corridas. Os níveis de esfoliação com esta nova prática atingiram também nível mínimo histórico.

Aug 16, 2017