Search Documents

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By J. E. Johnson

IT is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence in these respects on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control; the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in d practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the toll-gases, and that the ratio of CO to CO., will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Sep 1, 1905

Jan 1, 1902

By C. Okrusch, C. Roos, M. Akers, S. Rosenthal

Modern mining consistently faces controversy. Public sentiment impacts the permitting and development of mines, so a quality public relations (PR) program for mining companies may improve society’s impression of the mining industry. Developing mines face more permitting challenges than operating mines, which stems from a lack of societal trust given the history of mining and its impact on the environment. Two case studies were selected based on the type of public controversy they face to demonstrate how pervasive permitting issues are in industry. Both Pebble Mine, owned by Northern Dynasty Minerals (NDM), and Black Butte, owned by Sandfire Resources America Inc (SRA), experienced difficulties with their water permitting due to potential risks their mine developments posed to local fish populations. Pebble has, to date, failed in all of their attempts to become permitted due to concern for the water and the fish. Black Butte dealt with the same problems, on a smaller scale, but was able to become permitted. These two mines will be discussed in detail including local history, mine setting, mining history in America, prevalent culture groups, technology development, and intercultural communication competence (ICC). The mining industry needs to evaluate its ICC skills since ICC directly determines the effectiveness of PR. Based on Barna’s Stumbling Blocks for intercultural communication, methods for improving the mining industry’s PR will be suggested in the hope of easing the permitting process for future mines by developing ICC.

Mar 2, 2022

By H. A. Doerner

"The following report is submitted, in compliance with the request made by the Honorable W. H. Sproule, Chairman of the Committee on Mines and Mining, to the Director of the United States Bureau of Mines, that the bureau investigate the most modern processes for the production of radium from its ores. A thorough search of technical publications and patent office files was made. Outstanding authorities on the subject as well as persons claiming novel or secret methods were interviewed.Unlike most other elements, it is not possible for radium to occur naturally in a pure or concentrated form. This is because radium is one of a series of unstable elements which, by a constant, spontaneous, atomic disintegration, change from one element to the next in the series. Uranium is the ""grandparent"" of radium. The rates at which radium atoms are ""born"" and ""die"" are so related that only one part of radium can exist in equilibrium with three million parts of uranium. Consequently radium is only found associated with uranium minerals, and the ratio of radium to uranium is never more than one to three million. Since uranium is a rather rare element, the scarcity of radium is almost beyond comprehension. Nevertheless minute traces of radium can be detected in nearly all rocks.The carnotite ores of Colorado and Utah were the chief source of radium for many years.In the fall of 1922 news of the very rich deposits of radium ore discovered in the Belgian Congo caused most complete cessation of domestic production. The Congo ore contains pitchblende and a number of alteration products, including the new minerals bequerelite, curite, krasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent uranium oxide has been produced. It seemed certain that radium could be extracted from the Conga ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgian syndicate to market the foreign product in this country. The retail price of radium has been held at $70 per milligram, but large orders are filled as low as $50. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price with one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, finally shut down its plant."

Dec 1, 1930

By Sandra K. Zacharias

Brass, a deliberate alloy of copper and zinc, has been known since before Roman times. There are two main methods of making brass: (1) Cementation or calamine process - crushed zinc ore (calamine, ZnC03 , or calcined calamine, ZnO), is mixed with charcoal and small pieces of metallic copper and heated to about 900°C in a closed crucible, (2) Alloying - metallic copper and zinc are melted together in a reverberatory furnace. According to most modern authorities (e.g. Smith and Forbes 1955), the calamine process was the only one used in western Europe prior to the 18th century. At that time, the alloying technique began to take over, because metallic zinc was successfully produced on a large scale for the first time. Previously, this had been a problem because zinc vapourizes at 906°C or about the same temperature at which it can be reduced from its ore. Thus, some means had to be devised to collect and condense the zinc vapour (Tylecote 1976). Metallic zinc was known, however, earlier than the 18th century A.O. Several early finds have been made, including a rolled sheet of metallic zinc found in excavations at the Athens Agora dating to the 3rd to 2nd century B. C. (Farnsworth et al. 1949). The Chinese were producing zinc by at least the 10th century A. D. and, by the 17th century, Chinese zinc ingots were being imported into Europe by the Dutch East India Company (Needham 1974). Metallic zinc is also mentioned in several European documentary sources from the 16th century (e.g. Paracelsus, Agricola). This study traces the changes in Western brass making methods from Classical to Renaissance times by examining documentary and archaeological evidence.

Jan 1, 1999

Jan 1, 1900

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By A. D. McMahon

This survey is one of a series of Bureau of Mines publications designed to serve the needs of Government and industry for comprehensive information on mineral commodities and activities. Copper, a versatile metal, has been vital to all civilizations from pre-historic times to the present. Its essential value in antiquity and until the nineteenth century arose from its malleability and ease of working, its corrosion resistance and durability, its attractive colors in alloyed and unalloyed forms, and, of course, its availability. The principal uses were for tools, utensils, vessels, weapons, pipe, statuary and other objects of art, and for building and architectural purposes where formability, permanence, and beauty were necessary qualities. Utilization of copper based on these physical and mechanical properties has grown tremendously for commercial, structural, mechanical, architectural, and art items; and its capacity for forming numerous alloys has led to a myriad of applications from miniature copper and brass eyelets to huge bronze battleship propellers. The early nineteenth century marks the epoch of the greatest use of copper, transmitting electrical energy. This particular property of copper is fundamental to the spectacular growth of the electrical industry and all associated industries relying on electricity for power, light, and heat. More than half of all copper produced is used for transmission of electricity.

Jan 1, 1964

By A. L. Murray

First -aid training as an adjunct to safety is receiving more wide spread recognition in the industries every year . Moreover , the adoption of a program for giving firstaid training to practically all employees at a mine or plant is based upon the experience gained and good results obtained from standard first -aid instruction during the past two decades . In the near future industries that desire to maintain a low accident rate , to decrease compensation costs , to reduce lost time , and to build up an efficient , loyal working force , will recognize that training in first aid is one way of attaining these results with little expenditure of time and effort . Progressive organizations will require every man from the superintendent down to take first - aid training and not , as heretofore , only a small percentage of the working force . When employees learn that first - aid training can be applied not only at their daily tasks but in their homes and on tthhee highways ,, they will welcome the opportunity of learning how to care for injuries and perhaps save lives . In a limited way first - aid instruction was given to miners as early as 1899 . Later , in 1904 , a few of the companies in the Pennsylvania anthracite district inaugurated the distribution of first - aid packets to their employees and instructed them in the use of the contents . It remained , however , for a branch of the United States Government to grasp the real significance of widespread first - aid training as an effective means of saving life and minimizing suffering from the large number of accidents among workers in the mineral industries . The United States , owing to its vast resources , both natural and human , for

Jan 1, 1930

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

By D. B. RUSHhIORE

I. INTRODUCTION. OF primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must. have careful consideration. While a general discussion of the subject. of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity of the hoist, and the latter thus becomes of the first importance. * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910.

May 1, 1910

Geophysical Abstracts 1 - 86 wore issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 119 were issued in mimeographed form by the Bureau of Mines as Information it ion Circulars 7256, 7257, 7267, 7273, 7285, 7292, 7303, and 7310. 1. GRAVITATIONAL METHODS 7786. Barton, D. C.3/ Case Histories and Quantitative Calculations in Gravimotric Prospecting. Am. Inst. Min. and Meat. Eng., New York, Tech. Pub. 1760, 1944, 49 pp.

Jan 1, 1945

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Paul M. Tyler, R. M. Santmyers

Platinum and its allied metals osmium, iridium, rhodium , palladium, and ruthenium are the most costly of the better-known metals and combine properties that make them unique among the elements . For a number of isolated uses substitutes have been found which are cheaper and quite as satisfactory ; but none will replace platinum in many of its varied uses , and there is a large and growing demand for purposes for which no economical substitutes are known . As this paper is being written the supply of platinum tends further to increase as a result of the exploitation of newly developed resources and the expansion of production from older sources . In obedience to economic law prices have declined steadily . Buyers , always reluctant to commit themselves on a falling market , have maintained a waiting attitude , and consumption trends are not clearly indicated . Should platinum again approach the price of gold , the natural tendency would be to use more of the metal . In recent years , however , the industrial and scientific uses of platinum have become subordinate to its consumption in jewelry . In matters of personal adornment the popular whim and not practical utility is the dominant factor in demand , and it does not follow that lowered prices will stimulate demand . The substitution of white gold and certain plated goods for platinum may be checked by cheaper platinum , but a fickle public that turned from gold to platinum when platinum became the more costly metal can not with certainty be expected to buy more platinum jewelry because more of the metal than formerly may now be had for the same price . The dearth of platinum during and for some years after the World War had a profound effect upon prices , and this in turn wrought important changes in the field of consumption . When prices advanced the chemical industry, formerly the leading consumer of platinum, was forced to economize in its consumption of the metal and to substitute other metals whenever it could . Somewhat similar conditions resulted in the electrical industry and in the use of platinum in dentistry . Some of these former outlets are permanently closed , and others may be reopened now that platinum prices have receded to pre-war levels , but despite the general expansion of industrial and scientific activity since 1913 the demand for platinum outside the jewelry trade has suffered a net decline . Since the metallurgy of platinum is relatively simple the reason for its high price is its relative scarcity in the earth's crust . An interesting speculation set forth by certain geologists attributes the extraordinarily high density of the interior of the earth in part to the presence of iron alloyed with substantial amounts of platinum and other related metals . In support of this hypothesis it may be said that platinum is often found in meteorites , and known deposits in the earth's crust are all of deep - seated origin . However , even if there were a high concentration of platinum in the interior of the earth it would be next to impossible at the present state of our knowledge to make it available , and the world would continue to depend for its supply on deposits found within minable depths below the surface . For many years before 1914 the world obtained its supply of platinum metals primarily from Russia , which before the war produced as much as 300,000 troy ounces in a year , or approximately 95 per cent of the world output . Despite fluctuations due to internal political disturbances Colombia managed to account for 3 to 4 per cent , leaving the rest of the world to furnish the remaining 1 to 2 per cent .

Feb 1, 1931

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By AIME AIME

R. A. Hadfield, W. H. Bleckly, The Rt. Hon. Sir James Kitson, Bart., M. P.', E. Windsor Richards, E. P. Martin, Andrew Carnegie, Sir Hugh Bell, Bart., Bennett H. Brough. Patrons. Adamson, Joseph, & Co., Hyde; Aird, John, & Co., London ; .Akrill, C., & Co., Ltd., West Bromwich ; Anderson Foundry Co., Ltd.,. Port Clarence, Middlesbrough ;. Armstrong, Sir W. G., Whitworth & Co., Ltd., Newcastle-on Tyne ; As¬sociated Portland Cement Manufacturers (1900), Ltd., London; Babcock & Wilcox, Ltd., London; Baird, William, & Co., Ltd., Glasgow ; Baldwin's, Ltd., Stourport; Barclay, Andrew, Sons & Co., Ltd., Kilmarnock; Barrow Hematite Steel Co., Ltd., Barrow-in-Furness; Bayliss, Jones & Bayliss, Ltd., Wolverhampton ; Beardshaw, J., & Son, Ltd., Sheffield ; Bell Brothers, Ltd., Middlesbrough ; Bolckow, Vaughan & Co., Ltd., Middlesbrough ; Booth, Joseph, & Bros., Ltd., Leeds ; Briton Ferry Works, Ltd., Briton Ferry; Butlin, Thomas, & Co., Ltd., Wellingborough ; Butterley Co., Ltd., Alfreton ; Byrne, James, & Co., Middlesbrough; Cargo Fleet Iron Co., Ltd., Middlesbrough.;. Carnforth Hematite Iron Co., Ltd., Carnforth ; Cochrane & Co., Ltd., Middlesbrough ; Coltness Iron Co., Ltd., Glasgow ; Colville, David, & Sons, Ltd., Motherwell ; Consett Iron Co., Ltd., Consett ; Cooke, William, & Co., Ltd., Tinsley ; Craggs, R., & Sons, Ltd., Middlesbrough ; Darwen & Mostyn Iron Co., Ltd., Mostyn ; Dorman, Long & Co., Middlesbrough ; Dunlop, J., & Co., Ltd., Glasgow ; Ebbw Vale Steel, Iron & Coal Co., Ltd., Ebbw Vale ; Engineer, The, The Proprietors. of, Lon¬don ; Engineering, The Proprietors of, London ; Etna Iron & Steel Co., Mother¬well ; Farnley Iron Co., Ltd., Leeds ; Firth, Thomas, & Sons, Ltd., Sheffield ; Rather, W. T., Ltd., Sheffield ; Fraser & Chalmers, Ltd., Erith ; Frodingham Iron & Steel Co., Ltd., Doncaster; Gjers, Mills & Co., Ltd., Middlesbrough ; Glenboig Union Fire-Clay Co., Ltd., Glasgow ; Glengarnock Iron & Steel Co.; Ltd., Glengarnock ; Guest, Keen & Nettlefolds, Ltd., Birmingham ; Hadfield's Steel Foundry Co., Ltd., Sheffield ; Hall, J. & E., Ltd., Dartford ; Harkness, W.; & Sons; Ltd., Middlesbrough ; Harrison & Co., Ltd., Lincoln ; Head, Wrightson & Co., Ltd., Stockton-on-Tees ; Hill, John, & Co., Middlesbrough ; Hingley, N., & Sons, Ltd., Dudley ; Hopper, John I., Ltd., Thornaby-on-Tees; Hull Forge Iron &-Steel Co., Ltd., Hull; Iron and Coal Trades Review, The Proprietors of, London ; Ironmonger, The, The Proprietors of, London ; Jackman, Joseph, & Co., Ltd., Sheffield ; Jessop & Appleby Bros., Ltd., Leicester and London ; Jes-

Nov 1, 1906

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By G. M. Carr-Harris

"THE SUBJECT of permanent molding has received a great deal of attention in the technical press as illustrated by the many excellent articles in the bibliography which follows. In general, this covers the period 1940-1958 and is merely representative of what is available. Numbers in •brackets refer to items in the bibliography.It may be desirable at the outset to give a few definitions covering those terms directly related to this subject. The following is a definition of permanent-mold casting as given by J. W. Meier in a paper, ""The Non-Ferrous Metals and Alloys"", read before the Ottawa Valley Chapt.er of the American Society for Metals:""Permanent Mold Casting is used where a large number of castings of the same part are required and higher mechanical properties, greater density and closer tolerances are essential. Since metallic mold s are very expensive, the number of castings must be sufficient to, defray, at least partially, the added expense. Molds are usually made from a good quality cast iron, 1but other mold materials, such as the aluminum and copper alloys, graphite, ceramics, etc., are being used in certain cases. Important factors in permanent mold casting are the mold temperature; the proper mold dressing; and, as in all other casting methods, the mold geometry, that is to say, the design of spruces, gates, risers and vents""."

Jan 1, 1960