Search Documents

By Louis C. Brichta

"The O'Jack Mining Co.'s zinc and lead deposits in Jasper County, Missouri, have been worked intermittently since the early nineties; production from these deposits was greatest during World War I and II - 4,668 tons of zinc and lead concentrates. The deposits are in a sink-hole structure in which intense deformation has taken place and in areas of disturbance in the sheet-ground horizon.While high-grade ore was being mined, the operators sank seven churn-drill holes for the purpose of extending reserves. They then asked the Bureau of Mines to explore the deposit with the object of developing a reserve of lower-grade ore that could be mined by open-pit methods. Twenty-two holes were sunk. The methods of drilling and sampling and the logs of the holes, as of those drilled by the operators, are given later in this report.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mined has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts development by each exploratory project as soon as practicable after its conclusion. Preliminary examination, conduct of exploratory work, and preparation of final reports are functions of the Mining Branch, Lowell B. Moon, chief, under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By Eun-young Kim

Electrogenerated chlorine leaching of waste printed circuit boards was investigated in hydrochloric acid solutions. The pulverized printed circuit board contained about 37.6% of metal component, in which copper was about 83.6%. The leaching rate of copper was greatly affected by current density and agitation speed. The leaching of copper up to 98% was achieved at 20 mA/cm2, 50?, 180 minutes, and 600 rpm in 1M HCl solution. Increasing agitation and lowering current density enhanced utilization efficiency of electrogenerated chlorine. Leaching of copper was suppressed at initial stage, while the minor metal elements, such as aluminum, lead, and tin, were dominantly leached out.

Jan 1, 2006

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By F. Maciosek, D. Denton, J. Johnson

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and personnel from Coeur Silver Valley, Wallace, ID, conducted tests using rock strain strips and Split-Set rock bolts instrumented with strain gauges to monitor wall rock strain at the Galena Mine, Osburn, ID. The objective of the test was to identify whether strain on the rock bolts increased prior to a rock burst. Although results were inconclusive, researchers learned that the Split-Set rock bolts yielded in stick-slip fashion in the highly jointed walls of the stope. The bolts were also bent as stress was redistributed following blasting and subsequent movement along joints in the wall rocks.

Jan 1, 2004

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

Kudremukh Iron Ore Company Ltd, a wholly owned Government of India Enterprise, was established in the year 1976 to develop mine and plant facilities to produce 7.5 Mtpa of high-grade iron ore concentrate at Kudremukh. The mine and plant facilities were commissioned in 1980. In view of high demand for iron oxide pellets in iron and steel industry worldwide and as a diversification activity, a pelletisation plant of 3.0 Mtpa capacity was commissioned in the year 1987 at Mangalore for production of high-quality blast furnace and direct reduction grade pellets for export. The pellet plant capacity has been increased to 3.5 Mtpa by technological improvement which included installation of roll press for quality and productivity improvement. In addition, the pellet capacity is being increased to 4 Mtpa by the addition of Shaft Pelletising Furnace plant.

Jan 1, 1999

By A. Hultgren

PAGE Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots, and Its Influence on Crystallization and Segregation 2 Object of Present Investigation 16 theoretical Discussion of Process of Solidification 17 Gas Given Off from Rimming Steel during Solidification 17 Equilibrium Diagram of the Iron-carbon-oxygen Alloys 19 Solidification of Pure Iron-carbon-oxygen Alloys 25 Solidification When Carbon Monoxide Is Given Off at Constant Pressure... 25 Solidification When Gas Evolution Is Suppressed 26 Schematic Application on Solidification of Rimming-steel Ingots 27 Influence of Manganese, Sulphur and Phosphorus 28 Experimental Work 30 Liquid Steel and the Mold Gas 30 Ingots Investigated and Methods Used 33 Ingot Structure 42 Structure of Rim Zone 42 Structure of Core 49 Structures Obtained under Special Conditions of Freezing 50 Distribution of Metalloids 55 Other Observations Made 60 General Discussion of Solidification Process 63 Condition of Liquid Steel before Casting 63 Rimming Period 70 Composition of Rim Zone 93 Freezing after Top Is Closed 96 Slag Inclusions and Ingot Scum 102 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 103 Summary 105 Appendix-Preparation and Etching of Ingot Sections 106 References 107 IN 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, 1. Wohlfahrt and the authors. The present paper? is a somewhat

Jan 1, 1939

By George Goble

I hope that after the long evening and all the exercise that some of you took you won't be completely exhausted to listen to a little bit about pile testing. The topic that 1 have been given is pile testing. It seems to me useful to break this topic into some smaller pieces so that we can try and organize our thought a bit. As I understand the terms "pile testing", I believe we are really referring always to capacity, one way or another, so I am suggesting that we organize the things we are doing in terms of measurement of soil capacity and pile capacity. There are obviously two failure modes and we frequently speak of pile integrity rather than structural pile capacity, but it's really capacity that we are concerned about. Further within these breakdowns I am suggesting that we might look at the topic of soil capacity in terms of static methods and dynamic methods and, finally, within each one of these, measurements of axial capacity and measurement of lateral capacity. Also here some of these subdivisions might be there for the purpose of symmetry and finally the same sorts of breakdown in Pile Capacity area.

Jan 1, 1994

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

By T. W. Camm

"As engineers, we are trained to use logical, rational problem solving to insure our mines operate at maximum efficiency. We tend to use the same technical approach to design safety into all mining systems. This works well for machines, but not so much for the human component. Recent insights in the field of behavioral economics provide useful ideas for addressing the fact that we are driven by emotions more often than by rational thought. Understanding the nonrational aspect of human behavior is an important piece of any safety system design. INTRODUCTION The most common economic model is based on humans making rational decisions; that given the proper information, we will make a logical, rational decision based on what is best for ourselves (Ariely, 2009, p. xviii). In many cases this is an accurate description of how we make decisions. As an engineer, I was trained to apply the precision of mathematics and logic to solve problems. As an engineering professor, I now teach this approach to bright young minds preparing them for a life of professional effectiveness as practicing engineers. That said, we are not only rational. Daniel Kahneman, winner of the Nobel Prize in Economics, describes a model for how we think (Kahneman, 2011). System 1 is the part of our mind that is fast, intuitive, and emotional; while our logical, slower, and deliberative mind is System 2. According to Kahneman’s model, System 1 runs automatically, most of what you think and do originates in System 1. System 2 takes over when things get difficult, including the application of math and logic, and the resolution (or avoidance) of conflict. As engineers, we would typically assume that we operate in System 2 mode most of the time. This is where the model becomes useful, for Kahneman points out two important aspects of the dynamic between the two systems in our mind. First, System 1 has biases, systematic errors that lead to answering questions with an easier answer (rather than a right answer) before System 2 is engaged. Second, we can be blind to the obvious, and also be blind to our blindness. Complicating things further, System 1 cannot be turned off (Kahneman, pp. 24-25)."

Jan 1, 2015

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

During the extensive research which has been conducted in the Metallurgy Department of the University of Melbourne, into the properties of lead and its dilute alloys, the Brinell test has been used for the determination of hardness.The work described herein represents part of an investigation into the influence of various factors on such determinations, particularly when carried out on different qualities of "pure" lead. It is intended to publish the more theoretical and controversial aspects of this research elsewhere.MATERIALS USED AND THEIR PREPARATION FOR TESTINGThe tests to be reported have been conducted on a specially pure electrolytic lead, and several brands of commercially "pure" lead. The analyses of the samples upon which most of the work has been carried out are given in Table 1.Note: Oxygen was not determined, but from the work of H. W. Worner, in the Rosenhain Memorial Laboratory, it appears probable that it was approximately 0-0003% in all samples.

Jan 1, 1940

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By Marcello M. Veiga

Informal gold mining operations in the Amazon emit about 100 tonnes of mercury annually because of poor amalgamation practice. Lack of information and the complexity of mercury transformations hinder effective action to prevent such pollution and/or monitor its extent. In the past, mathematical equations have been formulated to deal with the correlation of natural variables and mercury in biota but often, the error range is too great to provide useful models. Projection of physico-chemical variations in an environment subjected to mercury emissions onto the extent of bioaccumulation is fraught with many uncertainties and unknowns such as internal correlations between variables and the site-specific nature of biota contamination. Often assumptions about closed systems are invalid when applied to natural environments. This work presents a heuristic approach to this problem in which amalgamation methods and natural variables are dealt with using an IF-THEN rule-based system that concludes about levels of emission and risk of bioaccumulation. The system is able to handle uncertain or vague data and yet still provide useful output. Belief in mercury oxidation or dangerous conditions are examined using Fuzzy Logic techniques and Inference Equations. These belief levels are derived from thermodynamic equilibrium data together with field observations of natural variables. This procedure can reduce the need for sophisticated analytical equipment and can provide information and diagnosis to non-technical people.

Jan 1, 1994