Search Documents

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By R. J. Wesely

In recent years the trend in copper smelting has been to expand existing smelters to increase their throughput. New smelters under consideration are large, typically in excess of 200,000 tons per year of copper. Despite this trend to larger smelters there are a number of conditions where a much smaller smelter can be economically viable. This paper examines these conditions and outlines the process concepts for a small smelter treating from 20,000 to 100,000 tons per year of copper.

Jan 1, 2000

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By D. Ducharme, J. Lenz

Operation of the Kidd electrolytic zinc plant commenced in 1972 with a cellhouse capacity of 105,000 tonnes of zinc cathode. The original cellhouse layout consisted of 42 parallel rows for a total of 588 cells. As leaching capacity increased, the cellhouse was expanded to 630 cells. Zinc cathode was manually stripped from plant start-up until the development of a mobile automated stripping system in 1994. Machine development continued until a second unit was placed in production in 1996, from which point, 60 % of the cellhouse was being stripped with the automated system. The final phase of the project was implemented in 1999 with the commissioning of two more automated strippers. This paper describes the implementation of the automated stripping system and its impact on cellhouse productivity.

Jan 1, 2000

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By T. Lezhava

For the purification of quarry waters from copper and their further utilization a three-sectional electrochemical reactor is constructed providing the extraction of 90-95% copper as a self-loosing powder from the quarry water running as a steady flow. Four variations of the integrated processing of quarry water are developed and their relative technical and economical parameters are calculated. The detailed technological scheme is given for the variant that is the most profitable for Georgia.

Jan 1, 2006

By Lakshman D. Jayaweera

Today's rapidly developing and changing technologies and industrial products and practices frequently carry with them the increased generation of materials that, if improperly dealt with, can threaten both public health and the environment. Mercury is an element that poses great problems in the many forms in which it is to be found in the mineral processing industry. These forms are often contained in hazardous wastes and residues which may be unstable, and in which the contained mercury has value. This paper presents some of the stabilisation and recovery methods which are based on hydrometallurgical techniques and thermodynamic stability considerations.

Jan 1, 1994

By Takeshi Yoshikawa

For the sake of effective control of titanium-compound inclusions in the steel-making processes, especially for stainless steel production, the influences of alloying elements of chromium, nickel, manganese, molybdenum, copper and oxygen on the thermodynamic property of titanium in molten iron were investigated at 1873K. At a certain titanium potential controlled by the coexistence of Ti3O5 and Ti2O3 doubly saturation of steels, the interaction parameters between alloying elements and titanium in molten iron were determined as follows. [ ] From the investigations on the equilibrium of titanium deoxidation in molten iron, the activity coefficient of titanium and the first order interaction parameter between oxygen and titanium were determined as follows. [ ] Also, deoxidation equilibrium for titanium in molten 304 stainless steel was measured and compared with the calculated results using the determined interaction parameters.

Jan 1, 2006

By Varadajan Seshadri

The increase in production of continuous casting machines requires long ladle sequences without interruption. Very often the production schedule has to accommodate a variety of steel grades. In such cases downgrading may be inevitable. Models must be made available to study the alternatives that would make possible mixing of steels in the tundish but minimizing the losses due to downgrading the slabs. Physical modeling was used to evaluate the influence of variables such as internal geometry of the tundish, presence of turbulence inhibitors, depth of ladle long nozzle, weight of steel in the tundish, steel throughput upon the tundish transition curve. Expressions for minimum residence time and transition period have been determined. Mixing-transition is allowed to continue inside the liquid pool in the mold and the final solute distribution in a given cross section is captured by a solidification model. The result is a map of the transition in the final product.

Jan 1, 2006

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Jakub Kaczorowski

In the production of Mn-alloys, the Boudouard reaction significantly influences the mass and energy balance. The endothermic nature of this reaction requires more energy for the process, while the direct consumption of carbon is reflected in the greater demand for carbonaceous raw materials. Therefore, it is desirable to eliminate or suppress the reaction. The kinetics of the Boudouard reaction are a function of many factors, of which coke properties and the conditions around the particles (i.e. temperature, gas composition) seem to be the most important. In the present study properties of selected single source and commercial metallurgical cokes are compared with reactivity results. The single source cokes represent a single coal that has been carbonized in a laboratory scale furnace. The commercial cokes are products of carbonization of coal blends under industrial conditions. The coke properties include proximate, ultimate and ash analysis. Also, coke petrography with carbon forms is included. The reactivity tests were performed on different particle sizes at various temperatures, gas compositions and gas flow rates. The experimental parameters were chosen to simulate the conditions in an industrial furnace. The results show that highly graphitized structure of cokes, minimal surface area and a low concentration of ash retard the reactivity. Of the other factors, the temperature and the gas composition have the greatest impact on the reactivity.

Jan 1, 2006

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By Cashman R. S. Mason

Removal of halides (fluoride, chloride) from metallurgical solutions can reduce corrosion rates and improve hygiene from decreased anodic chlorine evolution. This is particularly true for zinc sulphate electrowinning solutions. This paper describes the chemistry of a new process for the removal of halides from such solutions by solvent extraction ? the Teck Cominco Halogon? process, for which patents are pending. In this process, the halides are loaded directly from commercial zinc sulphate solutions and are stripped into a form suitable for disposal. Sulphate extraction efficiency is variable while maintaining halide extraction efficiency. The method of optimizing the solvent composition is demonstrated.

Jan 1, 2003