Search Documents

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By W. W. Albrecht

I. Introduction Refractory metals like tungsten, molybdenum, rhenium, tantalum and niobium and their compounds are essential ingredients of our modern technology. Especially in purified form, they are used in special alloys, electronics, optics and ceramics. The processing route from raw material to high purity refractory metals and their compounds includes, as a prime option, the following steps: - dissolution of raw materials. - liquid liquid extraction. - precipitation of high purity intermediate compounds. - calcination/reduction to high purity oxides/metals. Especially in the first three steps, major amounts of chemicals like acids or sodium hydroxide are used and, as by-products, substantial quantities of residues and effluents are generated. The impact of environmental regulations on these by-products and the attempt to reduce or minimize the amount of residues and effluents produced will be discussed in this presentation using Ta/Nb chemistry as the example. The basis of our considerations will be the way these by-products are handled at HCST, a major, and in some cases, the biggest producer of refractory metals (tungsten, molybdenum, rhenium, tantalum, and niobium).

Jan 1, 1992

By Guo Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By K. Sanjay

Factorial optimisation technique has been used to develop regression equations at different time intervals for extraction of manganese from precipitated manganese oxide/hydroxide in sulphuric acid using charcoal as the reductant. The three parameters chosen for a 23 full factorial design were : acid concentration, amount of carbon and temperature. The regression equations were used to predict >> 90% extractions as well as kinetic data.

Jan 1, 1996

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By F. J. Tavera

The column flotation technology, at first developed for application in mineral dressing, has received special attention in processing of non-mineral dispersions as a result of its low cost, high efficiency and relatively simple operation. This paper presents the results from the operation of a laboratory flotation column for the separation of vegetable oil and soap from aqueous industrial effluents, The flotation system was operated under continuous countercurrent conditions without and with additions of a cationic collector. The experiments show that it is possible to separate about 80% of the organic phase in a rougher flotation stage. These results suggest that the recovery of the organic phase is highly dependant on the dispersion characteristics (i.e. bubble size, gas holdup and bubble surface area flux) and the existing an optimum bubble size from which either smaller or larger, the recovery of the organic decreases.

Jan 1, 2003

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By W. John Rankin

The finite and non-renewable nature of mineral resources poses unique challenges for sustainability: How can mineral and material needs of society be satisfied indefinitely? How can the benefits of exploitation of minerals best be captured for present and future generations? How can the environmental problems caused by large scale mining and processing best be ameliorated? These issues are rarely addressed, or if so only incidentally, in traditional courses in geology, mining, metallurgy and materials yet addressing them will increasingly be a major role for professionals in the minerals and materials industry and related sectors and agencies. This paper describes a framework for examining these and other sustainability issues related to meeting future material needs from non-renewable resources. The framework may be useful for educational purposes, either as the basis of a dedicated subject or by including the elements of it throughout a traditional course in relevant subjects.

Jan 1, 2014

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By S. Niyomwas, R. G. Reddy

"A mathematical model was developed to describe the plasma gas and particle dynamics and conversion yields. The velocity and temperature fields in the plasma were calculated by solving 1 the Navier-Stokes equations and the thermal energy balance equations. Conservation equations for the system species consider the multi-component diffusion and chemical reactions. Through the application of this model, temperature distribution, flow fields, and production rates were computed. The model was used to study the thermal decomposition of ilmenite in the non-transferred arc plasma reactor. The computed production rates of TiN from ilmenite using nitrogen and methane gas mixtures, are in the range of 5 to 100 x 104 kg/m3/s at 2500 KIntroductionThe widespread interest in thermal plasma processing has stimulated a great deal of research effort into the various aspects of this process, including plasma' spraying, thermal plasma chemical vapor deposition, plasma synthesis of fine powders, thermal plasma decomposition, plasma melting, and plasma extractive metallurgy.In the plasma synthesis of fine powders, the earlier experimental and theoretical studies aimed at predicting the final products1-5. Then it was followed by more recent investigation concerning the profile of plasma gas velocity, plasma temperature and concentration. In this regard, useful plasma processing models have been reported by numerous investigation6 -11 which were increased by both theoretical analysis and measurement.As a result of this work a reasonable plasma-processing model is proposed. It is to be noted that all the thermal analysis that has been made neglected the fluid -flow effects. Also, in the analysis aimed at the quantitative description of the fluid-flow field, the effect of heat transfer was not taken into account."

Jan 1, 2000

By Jesus Gonzalez

Peirce-Smith converters (PSC) are long cylindrical chemical reactors where copper matte reacts with air. Traditionally, air is injected laterally through submerged tuyeres at different subsonic velocities. However, the accumulated experience in steelmaking, particularly in the basic oxygen furnace (BOF) process, shows that the gas bottom injection may improve the mixing efficiency of a liquid pool. The aim of bottom injection is to maximize the copper kinetic energy meanwhile avoiding excessive reactor splashing. When gas is injected from a single orifice at the bottom of a liquid pool, two main gas flow regimes can be identified, bubbling and jetting. In this work, a PSC with bottom air injection is studied by means of multiphase 3D CFD numerical simulations considering multiple air velocities. Special attention is paid to the bubbles and jet formation mechanism. The mixing efficiency is measured by calculating the turbulent kinetic energy of the copper matte.

Jan 1, 2008