Search Documents

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010

By Hebi Yin

A two-dimensional multi-scale solidification model was developed to study the heat transfer, fluid flow, and grain growth occurring in the molten pool during the laser engineered net shaping (LENS) process. This model coupled the finite element method to calculate mass, energy and momentum transport in the macroscale with the cellular automaton technique to calculate liquid/solid phase change at the microscale. The validation of the model was performed by comparing the simulation results with experimental data from previously published works, showing good agreement in temperature distribution and the dendrite morphology (size and shape). The simulation results showed that Marangoni convection, caused by the temperature gradient along the pool surface, played a critical role in determining the flow pattern in the molten pool and exerted influence on the pool size and shape. It was also found that columnar dendrites can be formed, with dendrite arm spacings as fine as a few microns due to the high cooling rate during the LENS process. In addition, the influence of fluid flow on the dendrite growth in the pool was discussed.

Jan 1, 2010

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Ulises Crossa Archiopoli

We describe a technique that allows rapid imaging of the thermal diffusivity of the sample by a modified photo-thermal technique. The thermal diffusivity in hardened steels strongly correlates to the hardness. Hence in a noncontact manner and with optical microscope resolution, a 2D map exhibiting the crystallographic phases and hardness of the sample can be retrieved. Two almost collinear laser beams scan the surface, one as a modulated pump and a second as a CW probe. The deflection of the probe carries information on the thermal expansion of the sample and with it, on the thermal diffusivity. It is shown that a single determination of the time delay of the modulation of the probe beam can be used to retrieve the thermal diffusivity.

Jan 1, 2010

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

By Jason M. Porter, Douglas L. Porter, David L. Olson, Travis W. Koenig, Van S. Blackwood, Brajendra Mishra, Robert D. Mariani

"Traditional alloy theory models have been applied relative to the three solid phases of uranium: alpha (orthorhombic), beta (tetragonal), and mainly gamma (body centered cubic)[l]. The Darken-Gurry and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer have been used to predict the behavior of four types of solutes: 1) Transition associated with alloying in and containment of the uranium fuel 2) Transuranic elements in the uranium 3) Rare earth fragmentation elements (lanthanides) 4) Transition metals and other fragmentation elements. Using these solute map criteria, elemental behavior have been predicted as highly soluble, marginally soluble, or immiscible (intermetallic phase formers) and have been used to compare solute effects during uranium phase transformations. The overlapping of these solute maps are convenient first approximation tools for predicting alloy behavior.IntroductionAn investigation is in progress to determine the role of various solute elements on size and shape of the 'Y phase field range for uranium to optimize the burning and material processing of nuclear fuel is in progress. Traditional alloy theory models based on correlations to elemental electronic and crystal properties are used to predict solubility and micro structural formation. The effectiveness of this model is based on microstructure property correlations. Darken and Gurry, and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer, models have been used to describe solute solubility with respect to uranium based the on correlation between elemental electronic structure and uranium phases. The alpha (orthorhombic), beta (tetragonal), and gamma (body centered cubic) phases have different solubilities for specific alloy additions as a function of temperature. Using the method of Waber, ellipse diagrams classified those solutes that should have broad solubility in the allotropes of uranium[2]. The predictive diagrams are made from four different correlations:"

Jan 1, 2012

By Rajesh S. Ransing

An intelligent tool has been developed to analyse the quality of diecast components. The influence of both design and process parameters has been studied in great detail. The tool, based on expert systems related technologies, can identify the causes for the defective castings manufactured. Design related causes such as gate position; gate area, runner design etc. as well as process related causes such as cycle time, cavity filling time and melt temperature are suggested by analysing the data on defective castings for a manufacturing campaign. This intelligent analysis is useful for both design as well as production engineers in the decision making process. All the causes for the occurrence of defects are classified into two categories. The firs category is the 'rootcauses' i.e. the causes which are related to the actual process, material and design parameters and which can be directly monitored. The second category is more abstract in nature and is classified as `metacauses'. These capture the scientific rationale implicit in the cause and defect relationships. This knowledge on causes and defects is represented in the form of a structured graph rather than by a set of rules, which, coupled with forward reasoning and heuristic search techniques results in an elegant and efficient approach. Uncertainties and the degree of relationship among causes and defects are represented by a fuzzy probabilistic model.

Jan 1, 1994

By Helga Larravide

A new on-line database of literature about copper has been created through a joint undertaking by the Copper Development Association Inc. and PROCOBRE-Chile, with funding provided in part through the International Copper Association, Ltd. The new database will permit Spanish-speaking technologists to access publications maintained by PROCOBRE-Chile by means of standard keyword searches. In addition, a new Spanish- English thesaurus has been written to enable Spanish-speaking individuals to search d access the Technology and Environmental databases of the Copper Data Center, which together comprise more than 80,000 publications dealing with the production, properties, uses and environmental effects of copper. Planned expansion of the new Spanish literature database is described.

Jan 1, 1999

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Jayagopal Uchil, M. Krishna, Shanta Sastcy

"Damping behaviour of aluminite particulate reinforced ZA-27 alloy metal matrix composites processed by compocasting method is studied. The weight percentage of particulate reinforcement is 0,1,2,3, and 4%. A dynamic mechanical· analyzer is used ·to measure the damping capacity and dynamic modulus at the natural frequency of the specimen over a temperature range of 30°C to 300 °C both in the heating and cooling cycle. The damping capacity of the material is found to increase with increase in temperature and weight percentage of aluminite reinforcement although this is accompanied by a decrease in dyliamic modulus.The damping capacity and dynamic young's modulus exhibit a sharp decrease in their values around 300 °C a8 ZA-27 alloy undergoes a first order phase transition in this region which is confirmed by Differential scanning calorimetric studies. Several damping mechanisms have been evaluated theoretically for the material under study. The damping capacity at low temperatures is attributed primarily to coefficient of thermal expansion mismatch induced dislocations and high intrinsic damping of the matrix. At higher temperatures the damping capacity is attributed to ZA-27/aluminite interface, phase transformations and thermoelastic damping.IntroductionMetal matrix composites. (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and lightweight [1-5]. At present, the usage of ceramic particles as reinforcement in MMCs has attracted considerable interest from scientists and engineers. The MMCs show substantially improved elastic modulus, strength, stiffiless, and tribological properties with low coefficient of thermal expansion compared with the unreinforced matrix material."

Jan 1, 2000

By Denise Cristina Oliveira Nascimento

Environmental considerations in addition to technical, economical and societal benefits are increasingly promoting the substitution of natural fibers for glass fiber in polymer matrix composites. However, natural fibers are heterogeneous in their dimensions, specially the cross section, which plays an important role in their mechanical strength. It has been found that the equivalent diameter of fibers such as sisal, ramie, pineapple and curaua correlates to different levels of tensile resistance. Piassava is a promising stiff natural fiber for composite reinforcement. In this work, a statistical analysis of tensile strength of piassava fibers using the Weibull methodology was performed. An attempt to correlate the fiber strength, obtained in tensile tests, with the diameter, precisely measured by means of a profile projector, was carried out. The results revealed an inverse dependence between the piassava fiber diameter and corresponding tensile strength. Fracture tip observation by SEM suggested a possible mechanism that could justify this inverse correlation.

Jan 1, 2010

By J. R. Kiji

The Cerro Matoso S.A. mine and smelter, in the Cordoba lowlands of northwestern Colombia, consist of a dedicated laterite nickel mine, ore blending, drying and an RKEF process to produce high-quality ferronickel. At a project investment of $400M, first production of ferronickel was in September 1982, and in its inaugural year CMSA produced 6,150 tons of contained Ni from a mined ore grade of 3.2% Ni. Initial operational difficulties resulted in a number of furnace run-outs, which impacted ramp up to design ore throughput of 128 dry t/h Since then CMSA has steadily incorporated process improvements and initiatives to take the single line operation to an ore throughput of 175 dry t/h. A second 175 dry t/h line was added in 2001 (investment of US$ 300M) to consolidate CMSA as one of the world's lowest cost Ni producers with an installed annual production capacity of 50-55,000 tons Ni. The most recent addition is commissioning of Phase I of an ore-upgrading project to counteract the effect of declining ore grades. Keywords: Laterite, ferronickel, pyrometallurgy, smelter.

Jan 1, 2004

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

By James W. Reeves

DuPont was the titanium metal pioneer who put the greatest effort into both R&D and commercial sponge and powder metallurgy production. This was concentrated in the period 1945 through 1963. The commercial results were development of the chloride process for TiCl4 using ilmenite, development and improvement of the Kroll process, development of a modified Hunter process to make titanium powder and commercial development of a direct powder process. The powder metallurgical process failed because of the inability to meet powder chloride specifications. All this work remained a trade secret until published in NMAB -392 by Mahla in 1983. There were other processes explored by DuPont, both improved sponge and powder processes. Much of this work has been continued by others but none, as of yet, resulting in new improved titanium metal capacity.

Jan 1, 2001

By M. Waladan

The top submerged lancing Sirosmelt system has been developed through laborator.y scale testwork and pilot plant trials for recovery of zinc from ISF slag. The effects of the process variables of gas injection rate, method of coal feeding, and temperature on zinc fuming rates were studied in the laboratory. It was found that the rate of zinc elimination was dependent on all of these variabl.es. The rate of zinc removal from slag was independent of zinc content of slag down to approximately 1.5% Zn, below which the rate was proportional to zinc content in slag. Pilot plant trials were carried out to evaluate a proposed process and results followed predictions from the laboratory scale tests. A comparison of the proposed process with conventional slag fuming operations is made and it is shown that the process has a number of advantages which have a significant impact on the economics of zinc slag fuming.

Jan 1, 1990