Search Documents

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By Steve Skelhorn, Dan Ifrim

"A tunnel project poses many challenges; the operation of the Tunnel Boring Machine (TBM) being one of them. Mechanized tunneling is known as a safe and effective alternative to other methods in terms of schedule and cost; however, efficiency can be severely affected by a bad TBM selection and qualification and employment of inexperienced operators. The success of a mechanized tunneling project involves a comprehensive and interdisciplinary consideration of all contributing factors such as TBM technical specification and selection, TBM design and procurement including ancillary equipment and tunnel linings. The tunnel equipment selection along with the operation can make or break the project. The objective of this paper is to address the importance of the skills and qualifications of the TBM crew with particularity to the TBM Operator. The study includes the Owner and Consultant involvement in the selection and pre-qualification of the TBM crew and specifically the TBM operator as well as the role of Contractor and TBM manufacturer in TBM operator training. This paper also analyzes the possibility of issuing a TBM operator certification, and discusses the benefits and significance of periodic training and certification programs. INTRODUCTION Training in the tunneling industry is not a new topic. The industry continues to evolve and become more complex with technology advances and expansion of mechanical tunnelling to mechanized shaft construction, large diameter drilling and mining industry applications. The need for professionals trained to operate mechanized tunnelling equipment is ever increasing, while there is a significant number of veterans who will be ageing out in the next 5 years. Consequently attracting young professional is a very important aspect of sustaining a qualified pool of professionals. For any given tunnel project, the owner and the engineer spend up to several years, studying the ground conditions during preliminary and final design. Post contract award the contractor spend additional months studying the ground again to develop the optimum means and methods for construction. All this time and money spent at the beginning of the project has the purpose of developing the optimum tunnel design, assessing the risk associated and implementing mitigation measures to reduce risks to acceptable levels. Following the tunnel design process, sophisticated TBMs are being specified and sourced to ensure the best tool for the job. The question raises here: Are there available experienced/trained professionals capable of operating these sophisticated machines?"

Jan 1, 2016

By R. E. Vivas, J. A. Villa

"Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.1 Mt/a (4.5 million stpy) of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this article and include improvements in geo-modeling, mine planning, and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution.Project overviewPeña Colorada is a mining company that produces about 30 percent of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in Fig. 1. Technological innovationsMost mining projects around the world typically follow the logic of “mining the next best ore.” Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that improved many aspects of the mine plan. The Peña Colorada block model has undergone 3 expansions to reflect additional information not available in the past. The model has expanded to the East and Southwest. The latest model expansion increased the total number of benches to 98 as a result of positive exploration results. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. Two sectional block model views in Hexagon Mining’s MineSight 3D, along with the pit designs and geologic solids are shown in Fig. 2."

Feb 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By Malcolm D. Flavel

Much has been said and written about the world's, and particularly the united states of America's, energy crisis. The relative changes between cost components of production have altered because the days of cheap energy have now gone. Decisions that made capital investment reduction attractive to treat large tonnage lower grade ore bodies appear to be no longer valid because average energy costs for comminution that were less than 1 cent per kilowatt hour in 1972, are now more than 3 cents and will shortly become 6 cents according to some projections. Increased capital investment to improve processing energy efficiencies are certainly going to be pursued. Energy today is the largest cost component in the average mineral production facility. It takes more than 12000 kilowatt hours to produce one ton of finished steel and more than 60000 kilowatt hours for each ton of copper and aluminum.

Jan 1, 1980

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016