Search Documents

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By Robert E. Thurmond

With modern exploration techniques, it seems likely that an increasing number of the orebodies to be found in the future will be under alluvial fans or valley fill. As a result, a larger proportion of open pit mines will be confronted with the necessity for removal of substantial quantities of alluvial overburden; whereas in the past, for the most part, the open pit mine operator has dealt mainly with hard rock. If this proves to be the case, methods, equipment, and costs for alluvium stripping will become an increasingly important factor in open pit mine planning. Several operations are now faced with this situation, and various methods and equipment are used. At Pima Mining Company's operation the stripping ratio is in the range of 6/1 Well over half of the stripping volume is alluvium. The alluvium is removed almost entirely by carryalls hauling direct to a waste dump. Some removal has been accomplished by shovel and truck operation; more will be done by this means in the future. At American Smelting and Refining Company's neighboring .Mission Mine, nearly all alluvium removal is by large shovels and, trucks. U. S. Borax's Boron operation is accomplishing alluvium removal with carryalls but has been investigating other methods and equipment. The various operations in the Gas Hills Uranium District in Wyoming are stripping mainly with carryalls, although some small draglines are employed. The M. A. Hanna Company in the Mesabi Range employs large draglines and conveyor systems for removal of glacial fill. Nchanga Consolidated Copper Mines in Northern Rhodesia strips overburden with a large excavating wheel and conveyor system. There are no doubt other open pit operations with which the writer is not familiar, that are handling large quantities of alluvial overburden.

Jan 1, 1963

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By James A. Pendleton

In response to Public Law 95-87 (SMCRA), Colorado promulgated regulations governing the mining of Coal. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence. All permitted underground coal mines within Colorado have approved subsidence programs. Preliminary monitoring results indicate the subsidence mechanical predictions have been sufficiently accurate to preclude material subsidence damage. The State of Colorado has developed a practical approach to regulating subsidence, which stresses monitoring verification of predicted subsidence phenomena. However, shortcomings exist in our ability to precisely predict the secondary consequences of subsidence, including effects to structures, the hydrologic balance and the environment. Lack of accuracy in predicting these secondary consequences results in uncertainty, necessitating conservatism in permitting. To avoid increasingly stringent permit restrictions, future research should emphasize the secondary consequences of subsidence.

Jan 1, 1986

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By William Gleason

"It is the largest mining exhibition in the world that attracts thousands of attendees from around the world to Las Vegas, NV once every four years. Despite the recent struggles in the mining industry, MINExpo International 2016 promises to be as big as ever. In the following pages, Mining Engineering takes a look what some of the more than 1,800 companies plan to showcase during the three-day exhibition.CaterpillarCaterpillar will support MINExpo 2016 with an exhibit showcasing machines, technology, expertise and practical knowledge that miners can apply to help address their cost, productivity and efficiency challenges in today’s mining environment.Caterpillar will once again occupy the largest space at the event and will showcase both surface and underground machines, but the talk at the booth will focus on how Cat technology and know-how combines to help mining operations address and solve the issues that are most important to them. The main stage in the exhibit will feature presentations describing how mining companies, Cat dealers and Caterpillar work together to improve operations.“The challenge for all in the mining industry now is to optimize operations — to drive costs down while creating sustainable businesses that can weather downturns,” said Caterpillar Resource Industries group president Denise Johnson. “We believe that through our expertise and the knowledge of our dealers —combined with innovative technologies and our growing data analysis capabilities — we can help them not only survive, but thrive in these challenging times.” Johnson was selected by the National Mining Association (NMA) to chair MINExpo 2016. “Chairing this show is a great honor, and it’s a testament to Caterpillar’s partnership with this critical industry,” she said. “We’re proud to be a long-time supporter of the NMA, and we are excited to participate in another MINExpo. It’s an opportunity for us all to learn from each other how to increase productivity, control costs and improve overall operations.”Surface mining displays. The surface mining section of the Caterpillar exhibit will showcase the new MD6420C rotary drill. This is autonomy ready and optionally equipped to leverage the safety and productivity benefits of Cat MineStar Terrain. This high-precision drill management system optimizes utilization and improves drilling and blasting operations by accurately guiding the operator and improving precision of hole placement and drilling depth — and the next step is fully autonomous operation, Command for drilling. The third-generation drill incorporates proven Cat components throughout for superior reliability and durability."

Sep 1, 2016

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By John Sasadi

The mining industry depends upon inexpensive water transportation. Today, large quantities of mined products are transported by ships over oceans, from continents to continents, over lakes and waterways to the ultimate users. Sometimes, the routes these Bulk Carriers travel cover only a few hundred miles, sometimes thousands of miles halfway around the world. Most of the products of the mining industries are relatively inexpensive. A significant portion of their cost to the ultimate users are in the cost of transportation and not in loading and unloading these commodities at the ports of origination or destination. So far, the industry has produced very efficient loading and un- loading installations, but has very little influence over marine transportation or the design of the vessels themselves. Very little was ever published dealing with integrated transportation systems properly correlating all phases of the operation; namely, loading, marine transportation and unloading bulk materials.

Jan 1, 1967

By A. W. Khair

This paper deals with the causes and mechanisms of pillar failure in a southern West Virginia coal mine. The conclusions are based on in-mine observations and analysis of mining methods, eyewitness account of the sequence of events, topographic and geologic conditions, and mechanical properties of mine roof, coal, and floor. The study indicated that massive pillar failure was caused by the collapse of the mine roof. The collapse of the mine roof was due to the combined effects of high lateral compressive stress and high extraction ratio causing excessive bending of the roof beyond its limit. It was assumed that the higher lateral compressive stress under such a shallow cover was probably due to the drastic change in the structural geology of the area and possible residual stresses. Eased on the analytical study it was concluded that the sudden release of elastic energy (shock) due to the rupture of the roof caused the squeezing of approximately eighty mine pillars.

Jan 1, 1983

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

By D. Berberick

Hecla?s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d?Alene mining district of northern Idaho. Main access into, and production from, the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk by J.S. Redpath to an original depth of 1,890 m (6,200 ft) in the early 1980s. The shaft is divided into four compartments (Fig. 1), with sets made of 225 mm x 175 mm (9 in. x 7 in.) hollow structural section (HSS) steel buntons and 150-mm x 150-mm (6-in. x 6-in.) HSS dividers spaced every 4.5 m (15 ft) down the length of the shaft. Two skip compartments on the east side of the shaft are equipped with 125-mm x 150-mm (5-in. x 6-in.) HSS steel guides and 9-t (10-st) skips with three deck trailer cages for men and materials. The west side of the shaft is divided into a manway, and a fourth compartment that was originally designed for a service cage. Shaft services consist of a 250-mm (10-in.) a compressed air line and 150-mm (6-in.) sandfill line along the south side of the shaft, and 250-mm (10-in.) discharge (gray) water and 150 mm (6 in.) fresh water lines on the north wall. The mine?s primary 13.8 kV power lines, as well as communication lines are located on the west wall of the shaft. The production hoist is a 3.7-m (12-ft) diameter, double drum, double clutch, 2,238 kW (3,000 hp), direct current unit equipped, at the time, with thyristor drives. The 30-year-old drives would prove to be problematic during the rehabilitation project, leading to an upgrade to modern ABB drives later in the project, after the shaft rehabilitation was complete. The shaft had been subjected to the typical wear and tear of 30 years of operation, including intermittent sandfill and muck spills, and, in the lower areas, some corrosion. During those 30 years, the west compartment, originally designed for the service cage, could only be accessed from a work deck on top of the skips or from the manway.

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993