Search Documents

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By B. Dias, P. C. Schutte

Work-related musculoskeletal disorders (WMSDs) affect the wellbeing of workers and result in poor quality work, lower work performance and decreased motivation. In contrast to ‘occupational’ diseases where there is a direct cause-and-effect relationship between hazard and disease (e.g., asbestos and asbestosis, lead and lead poisoning), ‘work-related’ diseases are multifactorial, where the work environment and the type of work that is performed contribute significantly to musculoskeletal disorders. WMSD is the term used to describe disorders and diseases of the musculoskeletal system (i.e. muscles, joints, ligaments, tendons and nerves). WMSDs are by definition a work-related phenomenon. The literature shows inarguably that certain jobs and certain work-related factors are associated with a significant risk of contracting a WMSD. It is assumed that repeated movements and postures, static work, continuous loading of the tissue structures or lack of recovery time, trigger or cause a pathological process that then manifests itself as a WMSD. This paper looks at the prevalence of the WMSD condition at three mines in South Africa: a coal, a gold and a platinum mine. Predisposing factors that include work factors, presentation of symptoms and psychological factors will be discussed in the paper.

Jan 1, 2003

By Mike McWha

Drivers to increasing RM use ?Compliance issues ?Section 12 JSE Listing Rules ?Canadian NI 43-101 ?Sarbanes Oxley ?Shortage of African ore reference materials ?Poor perceptions about quality of some local RM?s

Jan 1, 2005

By K. S. Liddell

The Kell Process has been developed for the extraction of platinum group metals (PGMs) and base metals from sulphide flotation concentrates. The process has been successfully tested on several different sulphide flotation concentrates, including those from the UG2 chromitite horizon and the Platreef mafic/ultramafic layer. It has been shown to provide high (>95 per cent) and selective extraction efficiencies for the key valuable metals, i.e. Pt, Pd, Rh, Au, Ni, Co, and Cu. The Kell Process consists of several commercially proven unit operations. S, Ni, Co, and Cu are first selectively removed by use of a pressure oxidation step during which the dissolution of PGMs is minimized. The residue from pressure oxidation is subjected to a thermal treatment to ensure efficient PGM recovery by subsequent chlorination. All the core steps are very similar to well-proven conventional unit operations in common use, as are the subsequent metal recovery steps to provide marketable end products. Typical metallurgical responses of flotation concentrates from UG2 and Platreef to the Kell Process are provided, and key outcomes of an energy comparison study with smelting are summarized in this paper. Kell presents a potentially substantial improvement in PGM concentrate processing technology, in terms of economics via much-reduced power costs, ease of processing, and various environmental benefits. It allows for the treatment of high-chromium low-grade 'dirty' concentrates, such as secondary concentrates from the platinum industry's 'mill-float-mill-float' (MF2) flotation circuits and concentrates from retreatment of tailings. It allows greater concentrate mass pulls, has higher tolerance to gangue intergrowths in concentrates, and its use can provide substantial increases in overall PGM recovery. Its adoption would be a step change in the platinum industry, and given the commercially proven unit operations embodied in the Kell Process, at much-reduced risk compared with other more experimental technologies. Since the initial process development work, significant improvements and refinements have been introduced as a result of further compre¬hensive testing and process modelling. Pilot-scale testing and engineering study work is in progress for several selected sites.

Jan 1, 2012

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By N. Baloyi, P. Popoola, M. Tlotleng, S. L. Pityana

"The advantages of using Nb and Ti-Nb coatings for improving the hardness and corrosion resistance of Ti6Al4V were investigated. It has been reported that Ti6Al4V used in orthopaedic implants tends to release toxic Al and V ions into the surrounding tissue. Thin layers of Nb and Ti-Nb were deposited on Ti6Al4V substrates using a laser metal deposition technique. The deposited material was analysed using optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffraction. The corrosion behaviour of the deposited layers was investigated using a Metrohm Autolab PG Stat101 compact potentiostat at 25°C in simulated body fluid. A Vickers hardness system was used to study the mechanical properties. Both Nb and Ti-Nb coatings exhibited good metallurgical bonding with the substrate. The microstructure and the XRD analyses for the Nb system showed that the ??-Nb phase was most dominant, while the Ti-Nb system comprised a mixture of the ?? and ?? phases. The average hardness of the Ti6Al4V substrate was 350 HV0.3, with a slight increase for the Nb coating (363 HV0.3) and a much higher hardness from the Ti-Nb coating at 423 HV0.3. The corrosion results show that the deposited Nb was more corrosion-resistant in the solution than either the Ti6Al4V substrate or the Ti-Nb coating. IntroductionMetals such as CoCrMo, 316L stainless steel, and NiTi alloy are used for manufacturing biomedical implants because of their distinct properties, including low Young’s modulus and resistance to corrosion (Ryan, Pandit, and Apatsidis, 2006). These implants are required to remain in the body of the patient for many years. Due to a favourable combination of mechanical and corrosion properties, titanium (Ti) and its alloys have emerged as the material of choice for biomedical implants. Nevertheless, their use is not entirely without challenges. For example, in total hip replacement, surface degradation and release of metal debris from metal erosion caused by friction limit the service life of the implant (Oldani and Dominguez, 2012; Manivasagam, Dhinasekaran, and Rajamanickam, 2010). Ti6Al4V is generally regarded as the material of choice, but it has been found that over extended periods of time, the combination of surface corrosion and erosion releases toxic aluminium (Al) and vanadium (V) ions into the body (Khan, Williams, and Williams, 1996). This has led to the investigation of titanium alloys containing niobium (Nb), zirconium (Zr), tantalum (Ta), and molybdenum (Mo) as substitutes for the aluminium- and vanadium-containing Ti6Al4V (Okazaki et al., 1997)."

Apr 1, 2019

By P. W. J. van Rensburg

Our mineral heritage - PRESIDENTIAL ADDRESS given by P. W. J. van Rensburg, Pr. Eng.. B.Sc. (Eng.)(Rand) INTRODUCTION Stone Age people were living in various parts of South Africa as recent,ly as a thousand years ago, when they were displaced by Iron Age people with a culture developed in the far north. These invaders brought farming, building, and the earliest mining developments to the Transvaal, thus ushering in the beginning of our great mineral heritage. It is of particular interest to record that, up to comparatively recent times, some of these people were excavating iron-bearing shale rocks for their smelting furnaces on the Melville Koppies in J ohannesburg. Although the most recent the iron-smelting furnaces discovered on these koppies is estimated to be some five-hundred years old, it believed that these Iron Age people were driven out, and their settlements destroyed, by Zulu impis only one-hundred-and-fifty years ago.

Jan 10, 1973

By M. B. C. Brandt

Richter magnitudes for seismic events were calibrated for use as a Local magnitude scale in the West Rand (WR), Far West Rand (FWR), and Klerksdorp–Orkney–Stilfontein–Hartebeesfontein (KOSH) gold mining areas. Richter magnitudes are currently calculated from seismograms recorded by local surface cluster networks using tabulated calibration values for Southern California, published in 1958. The Richter (1958) model is incorrect for distances of less than 30 km and should be applied only to crustal earthquakes in regions with similar attenuation properties to those of Southern California. When compared to the South African National Seismograph Network (SANSN), the cluster networks, on average, overestimate seismic event magnitudes by approximately 0.1 of a magnitude unit. A calibrated Local magnitude scale was derived by means of a multiple regression analysis between the Local magnitudes reported by the SANSN and the largest zero-to-peak trace amplitudes measured on the cluster network horizontal seismograms, after modelling the attenuation of the seismic waves as these progress from the epicentre to the station position. Magnitudes reported by individual stations for the same event show a significant scatter around the average magnitude owing to the near-surface amplifications of the seismic waves at the recordings sites. Average magnitude should be estimated using as many magnitudes of individual stations as possible to ensure an accurate estimate. Larger event magnitudes should be compared with those recorded by the SANSN.

Nov 1, 2021

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

By S. M. Rupprecht

"SynopsisThis paper is intended to document recent personal thoughts, opinions, and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) and its current usage by Competent Persons. Admittedly, some debates are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the SAMREC Working Group.Some of the more critical issues currently under examination are the definition of Competent Person and the potential registration of Competent Persons, the current re-write of the Code, and the introduction of reporting of Exploration Results, Mineral Resources, and Mineral Reserves on an ‘If not – why not’ basis, noncompliance with the Code and discipline, the role of the Johannesburg Stock Exchange Readers Panel, and the valuation of mineral assets based on scoping studies.IntroductionThis paper is intended as a personal memoir of recent thoughts and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) (‘the Code’). Admittedly, some debates, such as reporting of Mineral Reserves inclusive or exclusive of the Mineral Resource, are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the South African Mineral Resource Committee (SAMREC) Working Group. The author, who has been involved with the SAMREC Working Group since 2007, offers observations in his personal capacity as a professional mining engineer with the intent of getting practitioners to contemplate the influence of the Code on the mineral industry. Current practices in the compilation and reporting of Exploration Results, Mineral Resources, and Mineral Reserves are often deficient in adhering to the Code and a conscious effort must be made by the mining sector to improve the standard of public reporting, in particular Competent Person Reports (CPRs) and Public Reports issued by listed mineral exploration and mining companies."

Jan 1, 2015

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By R. Hart

In this paper, problems that have been experienced with the rockpass system at Kloof Mine No. 3 Shaft are described. Actions that have been taken to overcome the problems are also described. These include the use of slugshots to remove hang-ups, the abandonment and waste filling of passes, and design criteria adopted for an alternative pass system.

Jan 1, 2006

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013