Search Documents

By L. A. Vermeulen, D. D. Howat

A study was made of the performance of a rod mil operating without liter bars and with different arrangements of liter bars in the lining. . The results show that striking improvements in performance, increased throughput, and reduced consumption of liner metal and electrical energy can be obtained by a change in the geometry of the liter-bar arrangements within a mil. Rod mils of equal size fitted with the same arrangement of liter bars but operating at different speeds presented apparent anomalies in the relative consumption efficiency of electrical energy for the production of material smaller than 75 µ m. Marked savings in the consumption of liner metal were achieved by the use of an arrangement of alternating lines of higher and lower liter bars. A study of the relative performances of two large tube mils showed that the use of liter bars in one of the mils resulted in a marked reduction in the consumption of liner metal and electrical energy per ton of material smaller than 75 µ m in the product.

Jan 1, 1986

By R. M. Lamya

A semi-empirical kinetic model was developed for the atmospheric leaching of a Ni-Cu matte in copper sulphate-sulphuric acid solution. Kinetics of the leaching process was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate and particle size distribution. The kinetic model was developed on the basis of the leaching mechanism and chemical reactions of the leaching system investigated, and was evaluated by comparing the model predictions to experimental data. The model was found to satisfactorily fit the trends in the leaching of the metals, namely copper, nickel, cobalt and iron.

Jan 1, 2009

By J. C. Zachariades, D. M. Fraser

The leaching of pyrolusite in acidic ferous sulphate solution was studied so that the important factors governing the kinetics of the reaction could be determined. The reaction is very rapid, and was monitored by continuous measurement and logging of the redox potential in solution by use of a microcomputer. The relationship between redox potential and manganese extraction was established empiricaly for each set of conditions by the use of a technique in which a calibration run was conducted in paralel with each leaching run. The study involved a number of batch leaching runs, and demonstrated that, of the variables investigated, only the initial ferous ion concentration and the reaction temperature afect the rate of manganese extraction. The final extraction did not vary. The reaction was modeled from the results by use of the shrinking-core model and Britan's activation-energy model. The later was found to provide a significantly better fit to the data.

Jan 1, 1991

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By J. A. Wates

The paper examines the consequences of dam building with slime of high water content, and therefore Iow relative density, such as the tailings usually associated with the extraction of uranium. It shows how a Iow relative density reduces the practical maximum rate of rise, and hence the establishment cost, of slimes dams built by conventional means. Further hidden costs of such tailings dams are examined. It is concluded that dewatering of tailings before their disposal is the most cost-effective means of increasing the rate at which a particular dam can be constructed, or of reducing operating or stability problems on existing dams. In the longer term, underground disposal seems to be a feasible alternative. However, it is pointed out that there are other factors that can compound the operating difficulties, and that these should be investigated before remedial steps are taken.

Jan 1, 1983

By J. J. leR. Cilliers

ABSTRACT The recently introduced concept of negative taxation complicates estimation of the distributable profit of certain South African gold mines, and an assisted mine could operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. A simple diagram is presented from which the approximate working profit or loss, taxation payable or tax credit received, and the distributable profit of an assisted mine can be estimated directly for any combination of the four main variable operational factors: tonnage milled, recovery grade, unit cost and capital expenditure. INTRODUCTION The effects on the working profits of South African Gold mines caused by changes in unit working costs, recovery grade, tonnage milled and capital expenditure are readily estimated. For normal tax- and lease-paying mines the distributable profit is related to the working profit and the latter is a commonly accepted comparative measure of the profitability of an operation. However, the recently introduced concept of State assistance in the form of negative taxation1, i.e. a tax credit, for mines with a life of less than eight years complicates such estimates. A requirement of State assistance is that an assisted mine must lower its normal pay limit by 16 to 20 per cent, and it will be possible for a mine to operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. In the case of an assisted mine it is therefore necessary for management to judge the effects of changes in unit costs, grade, etc., in terms of distributable profit instead of working profit. This will require repeated calculation of tax to be paid or tax credits that will be received under the numerous possible combinations of the four main variable factors. However, with the aid of the diagram illustrated in Fig. 1, it is possible to assess at a glance the practical effect of these variables on the distributable profit of an operation not subject to tax on the normal formula, or small mine formula, with sufficient accuracy to decide whether a detailed analysis is required. USE OF THE DIAGRAM From the central point 'X' in Fig. 1, a range of tonnages milled per annum has been plotted along the north-bearing axis, a series of costs per ton milled in the northwestern quadrant, recovery grades in the northeastern quadrant, and capital expenditures in the southwestern quadrant. Starting from the tonnage milled per annum, a line is drawn east and west across the two northern quadrants up to the points where it reaches the desired cost- and grade-lines. From these points two north-south lines are drawn into the southern quadrants. A further line is drawn to the east from the point where the western north-south line crosses the desired capital expenditure. Distributable profit is read off in the southeastern quadrant where this line intersects the eastern north-south line. Every possible combination of

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

By N. E. K. Schuttler

Experience with Mars pumping of underground water by N. E. K. SCHUTTLER (Visitor) As the result of a planned increase in production, Vaal Reefs Exploration & Mining Company Limited increased the hoisting capacity of their existing equipment to its fullest extent and installed Mars pumps and a washing plant. The layout of the installation is described, and details are given of the modifications made to overcome its weaknesses. Plans to change the present four-stage system to a seven-stage system are outlined.

Jan 3, 1977

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By G. T. C. Emere, E. C. Hunter

The use of cylindro-conical settlers for the clarification of underground water by E. C. HUNTER- (Associate) G. T. C. EMERE-, B.A. (Hons.) (Keele) (Visitor) This paper analyses the performance of conical settlers on Harmony Gold Mine from 1959 to the present time, and describes the investigation that was undertaken to substantiate and improve the use of conical settlers for a new pump chamber in another part of the mine.

Jan 5, 1977

By D. F. Williams

The modelling, simulation, and design of processes for the recovery of gold from solution by absorption on carbon require the combination of a suitable rate expression with a description of the flow conflguration of the system. By the use of a suitable rate expression from the literature, methods are presented for the design of multi-stage countercurrent absorption systems corresponding to the commonly used carbon-in-pulp and carbon-in-column contacting systems. The sensitivity of the recovery to various design parameters is illustrated. These results have important implications in the choice and design of equipment.

Jan 1, 1985

By T. Gibson

It is generally accepted that South African coal mines have gone through the mechanization of most of its underground mines, and while there certainly were a lot of productivity improvements, the lack of visibility on these machines operating underground still leave vast areas for improvement. The average actual cutting time still remains very low, in the 30 per cent area, which leaves significant improvement possible. Currently all analysis is carried out using hand-written reports. Unfortunately this is subjective and often inaccurate because of human interpretation. In addition in order to avoid costly component failure, a monitoring system is required to warn of eminent failures and condition monitoring. The challenge faced was to supply and install a system that was ‘Open’ and could be retrofitted to existing machines in operation because of the current standard of communication links to the underground sections. In addition it was intended to use, existing ‘off the shelf’ software and hardware and adapting this for the harsh underground mining conditions wherever possible in order to reduce costs. As development occurred, as with all technology, doors opened to other opportunities such as, remote access data logging and Internet based reporting. We focused on the Voest Alpine Bergtechnik (VA) range of continuous miners, as need arose to achieve the desired cost improvements because of the strategy of service contracts the subsidiary company, Voest Alpine Mining & Tunnelling (VAMT) offer the mining industry in South Africa. This paper describes a data logging system that has been installed on various continuous miners that provides data in real time, on line, and that could be expanded to any electrically supplied underground mobile or stationary mining machine.

Sep 1, 2001

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986

By R. T. Rudd

The impact of slimes-dam formation on water quality and pollution by R. T. RUDD*, B.Sc., AMI (S.A.) CE (Visitor) This paper discusses the mechanics of pollution by slimes dams in the gold- and fluorspar-mining industry, as well as that caused by coal dumps and slurry dams. The effect of coal mining on two typical rivers in Natal is shown and the implications discussed. The implications and trends of sulphates pollution on the Rand Water Barrage in the Vaal River are discussed. The spread of pollutants (sulphates and fluorides) from the Reef and elsewhere, and the impact on urban use and agriculture downstream of the barrage, are illustrated. Conclusions and future policy are outlined.

Jan 12, 1973

By John Freer

As an innovation on the annual programme, the Excursions Sub-Committee organized a social get together of the Institute's Councillors and their families on Sunday, 27th February, 1983. Asian Mining - change of date The Second Asian Mining Conference, previously announced as being held in Manila, The Philippines, from 5th to 8th November, 1984, will now be held in Manila from 11th to 14th February, 1985.

Jan 1, 1983

By A. N. Brown

The importance of the minerals industry in the economy of the country is discussed, and the tremendous changes that have taken place over the past two decades, including the widespread application of computers and the use of mechanization, are outlined. A discussion of the future of the minerals industry points out that, with the rise in the price of gold, the life of the gold-mining industry can be expected to extend beyond that previously predicted, and that the demand for uranium, which has been depressed, is uncertain. As a result of the oil crisis, the demand for coal has increased and large expansion programmes are planned. These involve coal exports and the use of coal for the generation of electric power, for the production of liquid fuels, and for the smelting of metals. Technical challenges face engineers in every avenue of the minerals industry: in deep gold mines, underground coal mines, strip coal mines, and open-pit mines. Studies indicate that only one-third of the demand for trained mining and metallurgical engineers is being met and that the position is worsening. However, there are indications that the industry is succeeding in attracting more engineering students, and the supply is expected to improve. These efforts should be co-ordinated, expanded, and intensified. There is a need to ensure that sufficient teaching staff of the right calibre and experience are attracted to universities and technikons. The first degree course is comprehensive and basic, and specialization through post-graduate study should be encouraged. The influence of national service on the education and training of engineers is discussed.

Jan 1, 1982

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By I. J. A. Brackley

An investigation of the slope stability of a pit and failures of spoil dumps, carried out at Silicon Smelters quartz mine, Pietersburg, South Africa, is described. The major geological feature of the mine is the intensely foliated schist in the footwall, with exceptionally Iow strengths upon extensive discontinuities, and the similarly unusual strength properties of the dumped schist spoil. The selection of slope angles for the pit is described, and a proposal for the stabilization of the failing spoil dump by segregated dumping is explained.

Jan 1, 1985