Search Documents

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By L. Pretorius, S. Uludağ

This paper explores how to apply system dynamics principles to surface mining problems towards understanding the consequences of mining efficiencies. Some simulation examples related to machine and people performance have been used to demonstrate systems engineering concepts to mining engineers. The simulation tool used is Vensim, which is widely used in industrial engineering applicable to systems thinking, and systems dynamics. The science and mathematics behind the system dynamics as well as benefits and typical challenges are discussed to explore the applicability to mining problems. The benefit of having one less drill is easily quantifiable with the developed model which is one of many other measurable benefits, using the developed model. Some of the benefits of the improved quality of drill holes are not fully quantified as this depends on the mine specific inputs. There are examples of quantifying this in the other industries using system dynamics tools.

Sep 1, 2021

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

FOURTH INTERNATIONAL CONFERENCE ON VACUUM METALLURGY This Conference will take place in Tokyo from June 4th-8th 1973. The language used will be English. Inquiries should be addressed to: Mr S. Tabata, Conference Secretariat, The Iron and Steel Institute of Japan, (Nippon Tekko Kyokai), Keidanren Kaikan (3rd Floor), 9-4, Otemachi 1 - Chome, Chiyoda-ku, Tokyo, JAPAN. SYMPOSIUM ON BLAST FURNACE (A.I.M.M.) February 15-17, 1972 Circulars setting out the programme for the symposium, and registration forms, may be obtained from the Secretary of the S.A.I.M.M.

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4, which is the main product, and other waste metal chlorides. TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amounts of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify the effects of using different feedstocks.

Jan 1, 2014

By Y. Jiao, V. S. Thompson, D. W. Reed, Y. Fujita, J. E. Aston

Rare earth elements (REE) are vital components in modern electronics and green technology products. Supply is tight and global demand is expected to increase, leading to high risk for the economic and national security of countries largely dependent upon foreign supplies. Recycling of REE from consumer and industrial waste materials is a possible way to help meet demand. We have shown previously that biohydrometallurgy can play an economically and environmentally sustainable role in REE recycling, particularly if agriculture or food wastes are used to produce organic acid bioleaching agents. A challenge for organic acid-based bioleaching is the incomplete conversion of the carbon substrate to an optimal organic acid biolixiviant with high REE extraction capability from a variety of REE-containing feedstocks (e.g., mining wastes, magnets from end of life products, spent batteries, etc.). To help meet this challenge a metabolic model was developed for Gluconobacter oxydans to identify options for improving sugar conversion to organic acids. Model predictions were consistent with laboratory data for the microbial consumption of glucose and production of gluconic acid, and suggested that providing growth conditions with relatively high C:N molar ratios could result in lower pH biolixiviant production and thus improve bioleaching. Keywords: Gluconobacter oxydans, bioleaching, metabolic modelling, rare earth elements summaries 2019: U.S. Geological Survey, 200 p., https://doi.org/10.3133/70202434.

Jan 1, 2020

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By A. E. Voigt

Iron ore samples representing the input and output of several jigging experiments were analysed to determine the effect of particle size, shape, and density on jigging performance. Traditionally, the manual measurement of the size and shape of individual particles is very tedious and prone to inaccuracies and inconsistencies. Using a novel multi-view imaging technique the 3-dimensional representations of each particle in the sample was determined. From this representation several size and shape measurements were extracted, and these were correlated with the individual particle density measurements. A rigorous investigation into the confidence associated with density and the size and shape features as a function of sample size was conducted, thus allowing the significance of correlations in the data to be determined. The jig?s performance was seen to be clearly sensitive to density and markedly so to particle size, while the results for shape indicated the need for continued work in the definition of particle shape.

Jan 1, 2012

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By T. M. Louw, L. Auret, S. M. Bradshaw, F. F. Noelle

Modern industrial processes undergo frequent process state shifts due to changes in demand, feedstock or maintenance operations. Multimodal continuous process monitoring is therefore required for effective plant operation. Steady state analysis is a key component in effective multimodal monitoring. Various issues still remain in determining the starting and ending times of transition states. High dimensionality of process data is a characteristic that makes it difficult to select variables to consider when conducting steady state analysis. In order to address these problems, steady state detection on the principal component space is proposed. First, data undergoes principle component analysis to reduce dimensionality, then existing multivariate steady state detection algorithms are applied on the principle component scores. A novel algorithm, threshold PCA-SSD, is proposed and compared to an existing technique for steady state detection. The algorithms are investigated on high dimensional synthetic data Keywords: Multimode process, steady state detection, principle component analysis

Jan 1, 2020

By R. C. Nkhoma, K. A. Annan, S. Ngomane

The effects of welding current, electrode force, and welding time in a resistance spot weld were studied to investigate the effectiveness of welded joints between a thin EN10130: DC04 material and a thicker 817M40 part, through analysis of the microstructural and mechanical properties. All welded specimens were subjected to tensile testing at room temperature (25°C) and sub-zero temperature (–46°C) to test the strength of the welded joints. No full button failure was observed at either room temperature or sub-zero temperature after optimization of the weldng parameters. The fusion zone was observed to consist mainly of martensitic phase, due to rapid quenching, while the HAZ was composed of clusters of martensite in a ferrite and bainite matrix. The base 817M40 metal remained fully ferritic after welding. The hardness was found to increase with increasing welding current. An increase in nugget size, indicating good fusion of the weld, was observed with an increase in the welding current.

Oct 1, 2021

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By R. Pretorius, N. Mautsa

In a cobalt precipitation plant, phosphoric acid is used to eliminate excess uranium from the pregnant leach solution, resulting in a cobalt hydroxide product that has little uranium contamination. However, the amount of phosphoric acid added must be monitored and controlled to avoid financial and sustainability impacts and to prevent negative impacts on the final product quality. One possible solution to this problem is the use of online residual phosphorus measurement techniques to regulate the addition. By continuously monitoring the residual phosphorus levels in the solution, the plant can adjust dosing in real time to maintain the target residual phosphorus level. As a result, the cobalt precipitation plant can improve phosphorus level control, lowering the risk of overdosing, and ensuring consistent product quality. This approach can also improve process efficiency, reduce operational costs, and have a positive environmental impact

Jan 1, 2023

Despite the media's use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996