Search Documents

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

Broken Hill Mines-1968, edited by M. Radmanovich and J. T. Woodcock, published by The Australian Institute of Mining and Metallurgy, Melbourne, 613 pages. Price $A15. This volume, containing some 65 technical papers, was produced for the 1968 annual conference of the Australasian Institute held at Broken Hill to mark the 75th Anniversary of that Institute, founded at Broken Hill in 1893. That conference also coincided with the 85th Anniversary of the discovery of the Broken Hill mining field. This closely reflects the position in this country, where the Witwatersrand gold fields were discovered in 1886, and our South African Institute of Mining and Metallurgy will in March, 1969 be celebrating the 75th Anniversary of the founding of the forerunners of our Institute. There is a comprehensive report of the geology of the Broken Hill area and the mineralogy of the ore body, and there are reports on the mining methods and the metallurgical procedures which have been developed over 85 years of operation of one of the great mining fields of the world. The value of most of the papers is enhanced by a large number of illustrations and photographs. An early section covers the academic and practical aspects of rock mechanics, prospecting, and exploration techniques are described in some detail. A third of the volume is devoted to mining, with papers on 26 aspects. The breadth of the coverage gives an indication of much specialized development, research, and consequent maturity in all departments. The detailed treatment of metallurgical aspects such as sizings of individual mineral particles throughout the milling stages and the development of an on-stream analysis system for lead will commend this volume to the specialist. The committee responsible for the production of this volume, which brings together much information previously only to be found after searching through numerous publications, are to be congratulated on a well produced comprehensive review of many aspects of the mining and metallurgical fields. H.B.

By Maggi Loubser

"In a technologically advanced era, where process control is accurately maintained within the smallest error margins, and accuracy and precision are continuously improved, sampling is still left to the lowest paid employee in the company without training him or her properly to understand the relevance and importance of the task. In this paper the objectives of sampling in a process control environment is discussed and an attempt is made to link it to the theory of sampling. Some of the practical problems associated with implementing theoretical sampling principles in an industrial environment will be elucidated and some examples given on how compromises are made. Different methods of sampling will be discussed with real life examples from different manufacturing industries."

Jan 1, 2014

By B. K. Loveday

The use of large flotation machines is well established, resulting in substantial savings in both capital and operating costs. Therefore, when a new plant is designed, laboratory and pilot-plant tests should be used to simulate large flotation cells, or appropriate scale-up factors should be employed. 'Conference on titanium The Fifth International Conference on Titanium will be held from 10th to 14th September, 1984, in Munich, West Germany, organized by the Deutsche Gesellschaft fur Metallkunde e.V., in association with the American Society for Metals, Societe Francaise de Metallurgie, The Academie of Sciences U.S.S.R., The Japan Institute of Metals, The Metallurgical Society of A.I.M.E., and The Metals Society.

Jan 1, 1983

VERSLAG- REPORT No. 1365 STUDIES OF INCIPIENT FUSION IN THE SYSTEM CHROMITE- MgO- Al2O3-SiO2-C 5th January, 1972 Investigator: N. A. Barcza SYNOPSIS A fundamental study was made of twelve chromite ores by use of a thermobalance under atmospheric and reducing conditions. It was found that their thermal behaviour under atmospheric conditions can be related to the mineralogical composition of the chromite spinel and the gangue. The overall mechanism of reduction with solid carbon over the temperature range of 1 200 to 1 500°C was shown to be diffusion of carbon through the reaction product. The effects of additions of fluxes and variations in particle size on the kinetics and mechanism of reduction were determined. It was shown that carbon monoxide does not reduce chromite ore up to temperatures of 1 550 °C, and it can therefore be eliminated as the diffusing reducing species. However, the reaction product of reduction, namely a mixed carbide of iron and chromium, was shown to be an effective reducing agent for chromitc ore, while also facilitating the transport of carbon. VERSLAG - REPORT No. 1380 AN ELECTROCHEMICAL MODEL FOR THE LEACHING OF URANIUM DIOXIDE 10th January, 1972 Investigators: C. R. S. Needes, M. J. Nicol SYNOPSIS A correlation between the rate of leaching of UO2 and the electrochemical properties of the oxidant concerned has been derived. This correlation is found to be borne out by experimental results. Certain effects observed in UO2 leaching and hitherto unexplained have been clarified in terms of an electrochemical mechanism. Experiments have shown that the mixed potential of a UO2 electrode gives a measure of the rate of dissolution of UO2. Its significance to commercial practice is discussed. CONCLUSIONS (I) The dissolution of UO2 in the presence of a number of oxidants can be explained in terms of an electrochemical mechanism. (2) The mixed potential of the UO2 electrode is a measure of the rate of UO2 leaching. This principle could be used in the control of industrial leaching operations. (3) A simple treatment has provided a mathematical basis for a fundamental correlation between the rate of U02 dissolution and the chemical properties of the oxidants concerned. This relation has been found to agree well with experimental results. (4) A number of phenomena occurring during the leaching of UO2, hitherto not explained in a satisfactory manner, have now been clarified in terms of an electrochemical mechanism.

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By H. L. Monro

Contribution by B. K. Martust I congratulate the author on his interesting paper. In my view, the establishment of the level at which South African gold output is at some kind of optimum is an interesting though somewhat academic exercise. Contribution by D. M. Hawkins* The thesis of the paper is a very interesting one, but, before it is used as the basis of any firm proposals to restructure the mining industry, which changes may be irreversible, one should be very sure that the basis of the calculations is sound. Contribution by P. J. Niewenhuizen* The hypothesis advanced by Mr Monro that the demonetization of gold in August 1971 introduced a major new policy variable, namely the supply-pricejdemand-price relationships, into the decision making process touches on a matter that has never really been given serious thought by the industry. Contribution by B. G. Kingsman* As a co-worker on the development of an econometric model for supply and demand in the world gold market with Mr H. L. Monro, it would perhaps be useful for me to make some comments on the various points raised in the discussions on his paper.

Jan 1, 1984

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020

By M. Verri

[ ]

Jan 1, 2009

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

By X. B. Zhao, J. G. Cai

When stress wave propagates through fractured rock masses, the wave will be slowed and attenuated due to the presence of these fractures. If the amplitude of stress wave is large enough to mobilize nonlinear deformation of these fractures, they will present different effects on one-dimensional P-wave propagation compared with those of linear deformational fractures. The static BB model is adopted to describe the nonlinear deformational behavior. Method of characteristics combined with displacement discontinuity theory is used to build analytical solutions of wave particle velocities and wave stresses. These equations are numerically solved with sufficient accuracy.

Jan 1, 2003

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

1. Book reviews Mining and metallurgical practices in Australasia. Melbourne, Australian Institute of Mining and Metallurgy, 1981. $40 (incl. surface postage). Reviewer: M. G. Atmore Coal mine ground control, by Syd. S. Peng. 1978. Reviewer: C. F. Engelbrecht Sixth Annual International Conference on Coal Gasification, Liquefaction and Conversion to Electricity, July 31 -August 2, 1979. Pittsburgh, School of Engineering of the University of Pittsburgh, 1980. Reviewer: S. T. J. van Rensburg This book is a useful general reference volume on the topics covered provided a great deal of technical detail is not required from it. It consists of 29 papers, which are arranged under 6 headings. Flotation agents and processes. Technology and applications, edited by M. W. Ranney. Park Ridge, D.S.A., 1980. $48. Reviewer: R. P. King 2. New books Project control manual, by Sven R. Red. 250 pp. in loose-leaf binder. U.S. Al47. (Obtainable from the author at Bray Studios, Windsor Road, Windsor SL45 UG, England.) Manganese deposits, by Supriya Roy. London, Academic Press, 1981. 400 pp. Joint preparation for welding (set of overhead-projector transparencies). Abington (England), The Welding Institute, 1980. £34 per set. Electron micrographs of clay minerals, by T. Sudo,S. Shimoda, R. Yotsumoto, and S. Aita. Amsterdam, Elsevier, 1980. 228 pp. Dfl.150. Weld pool chemistry and metallurgy. Abington (England), The Welding Institute, 1980. 357 pp. $27. 3. New journal ...being known as Gliickauf + Translation, at an annual subscription of 396 DM for 24 issues per year. It is available from Verlag Gliickauf GmbR, D-4300 Essen I, P.O. Box 103945, Federal Republic of Germany. 4. Canadian MRI publications During 1980 the Mineral Policy Sector introduced a new series of reports identified by the prefix MRI. These cover internal studies and analytical works on a wide variety of subjects, that for one reason or another, do not reach the publication stream of the regular series yet may be of interest to readers in this 'unpublished form'. Twenty-four such titles are listed below. Exploration planning A series of professional advancement seminars for the mineral industry is to be held at Rhodes University from 12th to 20th August, 1981. The series, entitled 'Economic Guidelines for Exploration Planning', will be conducted by Professor B. W. Mackenzie, and the attendance will be limited to 30 participants. The seminars are intended Seminar on Geostatistics A seminar for mining executives on Geostatistics and Decision Making in the Mining Industry is to be held in Toronto from 23rd to 25th September, 1981. v

Jan 1, 1981

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By F. J. N. Stassen

SYNOPSIS The effect of conditioning energy on the flotation of gold, U308, and pyrite was investigated in the range 0,1 to 100 kWh per tonne of dry ore for various combinations of conditioning time and impeller speed in a cylindrical con¬ditioning tank. It was found that, when the conditioning energy was increased to between 5 and 10 kWh per tonne of dry ore, the total recovery and flotation rate of the valuable minerals (expressed as Klimpel parameters) increas¬ed substantially. The Klimpel parameters are dependent on conditioning energy, but are independent of condition¬ing time or impeller speed (at constant conditioning energy). The Klimpel parameters of the gangue are indepen¬dent of conditioning energy.

Jan 1, 1991

By B. Friedrich

In a German governmental funded three-year research project, a closed loop recycling process for Nickel-Metalhydride-Batteries (NiMH) is under development. Today the discarded batteries are used in the steel industry as a cheap nickel source. Cobalt and rare earth (RE) are slagged and lost for reuse. The entire value of the metals in discarded Ni-MH is estimated to be 4?-4.5 ?/kg. Spent NiMH-batteries containing 36?42 per cent Ni, 3?4 per cent Co and 8?10 per cent rare rarth (Ce,La, Pr, Nd). The dismantled and processed NiMH-batteries are melted in a DC electric arc furnace producing a nickel-cobalt alloy and a slag phase highly enriched with RE-oxides. The key to success in this process is to find a suitable slag system, which ensures best separation of NiCo-alloy from the rare earth oxides and high concentration of RE in the slag. Different oxidic and halogenic slag systems are investigated in the melting process. So far a slag system based on 65per cent CaF2 and 35 per cent CaO delivers the best separation of the two phases and metal yields. A slag with a composition of 20?25 per cent La, 13-16 per cent Ce, 1.5?2.5 Pr, 4.5?6.5 per cent Nd is obtained and further treated to misch metal hydro-/electrometallurgically. The first results of the influence of rare earth oxides on the density of CaO-CaF2slag system are shown at 1600°C. Keywords: battery recycling, CaF2, CaO, rare earth oxides, slag characterization, density measurement

Jan 1, 2004

By J. P. Gouvea

Back-analysis of two mining-induced tremors in 2011 was used to determine a modelling criterion for the entire Klerksdorp Goldfield (i.e., Vaal Reefs region). At that time, most mining operations in the region were owned by AngloGold Ashanti (AGA) and shared many geotechnical similarities. By 2018 AGA had sold off all its Klerksdorp operations to different mining companies, which continued applying the 2011 modelling criterion. As mining activities became more remote, scattered, and isolated, the extraction of isolated blocks of ground and remnants became increasingly necessary. However, the inherited criterion allowed only minimal or no mining activities at these areas. Keeping in mind that safety is the overriding consideration, an innovative numerical modelling approach, which includes the application of peak particle velocity designs, was developed to provide practitioners in the Klerksdorp Goldfield with a suitable criterion to justifiably and safely mine isolated blocks of ground and remnants. This would not always be possible if a conformist approach was used.

Mar 14, 2024

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

By H. Hamma, R. Fehrmann, M. Gaune-Escard, G. Hatem, S. B. Rasmussen, K. M. Eriksen

The molten salts M2S2O7and MHSO4, the binary molten salt systems M2S2O7-MHSO4and the molten salt-gas systems M2S2O7-V2O5and M2S2O7-M2SO4-V2O5(M = Na, K, Rb, Cs) in O2, SO2and Ar atmospheres have been investigated by thermal methods like calorimetry, Differential Enthalpic Analysis (DEA) and Differential Scanning Calorimetry (DSC). Fundamental thermodynamic data like temperatures and molar heats of solid-solid transition and fusion, phase diagrams, heat capacities of solids and liquids, heat of mixing, and heats of complex formation have been obtained and are reviewed here. Also EPR spectroscopic evidence of V(IV) complexes and their structure are reported and the results are discussed in relation to the mechanism of SO2oxidation by V2O5based industrial catalysts. Keywords: Alkali pyrosulfates, alkali hydrogen sulfates, vanadium pentoxide, EPR spectroscopy, complex formation

Jan 1, 2004