Search Documents

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

By Gerald W. Elger

This report compares the quality of zirconium metal prepared by batch reduction of zirconium tetrachloride by (1) sodium, (2) magnesium, and (3) mixtures of sodium and magnesium. Criteria for quality are based on chemical analyses and hardness testing of zirconium arc-melted from sponge. The best quality zirconium with respect to low oxygen content and hardness numbers was prepared by reaction of zirconium tetrachloride with a mixture of sodium and magnesium. It was found that this reaction could be successfully carried out by two methods: (1) addition of sodium and magnesium before the initial reaction and (2) periodic injection of sodium during reaction of zirconium tetrachloride with magnesium. The largest quantity of metal was found to be recovered from experiments in which a mixture of sodium and magnesium was used. Magnesium appeared to be a better reductant than sodium because magnesium-reduced zirconium contained less oxygen and exhibited lower hardness numbers than sodium-reduced metal.

Jan 1, 1962

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By K. Hennings

Noise from vibrating screens is generated in two ways: 1) Noise due to the material being processed and, 2) noise from the screen itself. Non-metallic decks had been shown previously to reduce material noise. The noise reduction and change in screening performance was quantified for six non-metallic decks using dolomite, granite and coal as the materials. The non-metallic decks were from 2 to 7 dBA quieter and from -1 to +10 percent less efficient as compared to a steel wire cloth deck of the same open area. Damping of the sidewalls and isolation of the drive mechanisms had been shown, in a development configuration, to reduce the noise of the screen itself. Tests of four prototype damping treatments gave reductions up to 4.9 dBA and the mechanism isolators gave an additional 2.1 dBA. The treatments were successfully life tested in two ways: 1) Lab tests to a simulated 25,000 hours were conducted on samples of the treatments in a corrosive salt spray to simulate coal plant wash water and, 2) the full size treatments were run on a full size screen for 5,000 hours.

Jan 1, 1980

By H. W. Busch

In the course of examinations by representatives of the Bureau of Mines of several compressed-air systems in which explosions had occurred, samples were obtained of the carbon deposits that are formed normally in various parts of the systems by decomposition of the compressor lubricating oil. Experimentation with these carbon deposits has demonstrated that they contain a "carbon-oxygen complex" similar to that formed on coal and on other carbonaceous materials and generally recognized as being the cause of spontaneous heating of coal. The exothermic properties exhibited by such a complex are considered significant in relation to the possible initiation of combustion reactions that may lead to explosions or formation of carbon monoxide in compressed-air systems. This report discusses the occurrence of explosions and formation of carbon monoxide in the use of compressed air and presents results of experimentation conducted with carbon deposits from air compressors.

Jan 1, 1949

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discusses the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that -,re being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. 3. Clay in 2 paper cartridges. 4. Commercial hydrated lime in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By Sidney Speil

In the study of clays and related minerals, the analytical techniques commonly employed in mineral analysis are not always applicable. The X-ray examination of a clay sample usually will show the major constituents, but often minor· clay impurities will not be detected because of line broadening and the similarity of the main lines of clay· mineral diffraction patterns, The petrographic analysis of clay minerals with clay particles as small as a few microns is usually difficult. With still smaller particles, a gross effect often is noted in which a mixture of several constituents gives the appearance of a single constituent with the mean optical-characteristics of the mixture. 3/ The electron microscope has recently been used to study clay particle shapes of various aluminosilicates. 4/ However, this method has not yet been sufficiently explored. The Chemical method in which a mineralogical analysis is calculated from the oxide chemical analysis has been discussed by Wilson 5/ and others, and many of the shortcomings have been pointed out. It should also be recognized that the variable alkali and alkaline earth content of bentonites makes it inaccurate to assign these basic elements arbitrarily to feldspar or mica in any clay that contains appreciable bentonite.

Jul 1, 1944

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By R. R. Sayers

The contemplated use of dichloro-difluorco methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for public buildings and possibly homes, brims attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorino compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines as requested to make a laboratory study of the toxicity and potential hazard, and it was ca the oasis of the results is of this work and the results of a preliminary investigation made in another laboratory6 that the compound has been selected for commercial use. The investigation conducted by the Bureau of Mines is still in progress, enough information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:

Jan 1, 1930

By Bruce F. Grant

This report discusses research being done by the Petroleum and Natural Gas Branch und the Applied Physics Branch of the Bureau of Mines to deter-mine the most effective uses of explosives in shooting oil and gas wells, as measured in terms of rates of production from the wells. An experimental investigation of the effects of detonating explosives in shallow holes drilled in rocks, chosen to be similar to those forming oil and gas reservoirs, forms the basis of this study. Records obtained from strain gages placed in the rock around the experimental shots permit determination of the generation and propagation characteristics of the strain wave. Water-injection tests made on the test holes before and after shooting allow the increase in fluid conductivity resulting from the shot to be determined. By rotating these data to the physical properties of the rock, and by conducting shooting experiments over the range of rock types common to oil and gas reservoirs, it is expected that relationships between the fluid conductivity and the properties of the explosive and rock can be developed and used for designing efficient shots for oil and gas wells. Four series of experiment.al tests were completed during the summer of 1949 and are described herein. The results of these tests confirmed the feasibility of the experimental approach and permitted outlining the plans for future research discussed in this report. This report is presented to acquaint industry with this research program and the progress to date, so that the Bureau may have the benefit of suggestions from interested readers.

Jan 1, 1950

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discussed the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that are being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. Clay in 2 paper cartridges. Commercial hydrated lira in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940