Search Documents

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By A. E. Kehew

Earth resistivity surveys using the Wenner electrode configuration were made in unmined areas and reclaimed spoils at three surface lignite mines in western North Dakota. The study sites were the Center, Indian Head, and Falkirk Mines. Automatic interpretation of the curves was accomplished with the method of Zohdy and Bisdorf (1975). Overburden materials become more homogeneous with respect to resistivity during the mining and reclamation process. The spoils curves show localized hetero-geneities probably related to discontinuous moisture content variations in the spoils. Consistent resistivity differences in spoils occur between mines with over-burdens of different mineralogic compositions. Groundwater chemical composition in terms of total-dissolved-solids (TDS) is inversely correlated (r=-0.61) with apparent resistivity at the 80-foot spacing from a survey centered at a piezometer screened near the base of the spoils. Better inverse correlation is probably pre-vented by high variability in TDS within the spoils groundwater. A useful predictive relationship may be the plot of mean apparent resistivity at the 80-foot spacing for ar. entire mine against mean TDS for all wells in spoils at that mine. Data from more mines are needed to test the hypothesis.

Jan 1, 1982

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By Francis C. Lincoln

"INTRODUCTION As part of a general investigation of the zinc-producing area of southwestern Wisconsin, the Bureau of Mines undertook a limited amount of exploratory drilling in the immediate vicinity of the New Dale Rundell mine, in the Mifflin District of Iowa County, Wisc.The work was carried out during the early part of 1945, at a time when all effort was being directed toward increasing production of metals important to the Nation's war program. Bureau of Mines engineers decided to conduct exploration at the New Dale Rundell mine after a preliminary study of available data showed a reasonable possibility of indicating an important deposit. Before the Bureau of Mines investigation, 50 holes had been drilled in the vicinity. Of this number, 18 encountered ore of minable grade. Subsequently the mine was developed and operated for a brief period; however, work was stopped before all of the ore disclosed by drilling had been mined. There appeared to be a correlation between the ore shown by the drilling in the New Dale Rundell mine and another disclosure some 1,500 feet to the northwest. The Bureau of Mines exploration was pinned to explore this possible correlation. Of the 7 holes drilled by the Bureau of Mines, 3 disclosed minable ore beyond the limits of previous drilling."

Aug 1, 1946

By Thomas M. Sweeney

This open-file map is a quick reference containing location, ownership, and general lithology information on 124 active or significant Nevada gold mines. The map includes all counties, significant towns, and major highways in Nevada to aid in mine location. Several geologic trends with which the mines are associated are also depicted. General ore genesis for each deposit, including sedimentary, volcanic, plutonic, and placer-hosted deposits, are also identified. Gold mines are also listed alphabetically, by mine name, on the map. Each entry includes the appropriate county, percent of company ownership, operating company, and the property status as of May 1992. For additional information, contact Thomas M. Sweeney, U.S. Bureau of Mines, Western Field Operations Center, 360 East Third Avenue, Spokane, WA 99202; telephone (509) 353-2700.

Jan 1, 1993

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By L. J. Froisland

The U.S. Bureau of Reclamation requested U.S. Bureau of Mines (USBM) assistance in developing design data for moving lead-zinc-gold tailings from their current location without disrupting the existing chemically stable conditions. This report presents results of USBM work in determining (1) the minimum required time to air dry the tailings to approximately 20 pet moisture under various drying conditions both in the laboratory and in the field, (2) the degree of oxidation or reduction that occurs during drying, (3) the effect of lime or cement addition before drying, and (4) the likely equilibrium conditions of the dried tailings after deposition at the new location. The limited number of tests performed by the USBM in the available time frame established trends in oxidation levels but did not provide absolute statistical validity of data values. All data from drying and oxidation testing are included in appendices to this report.

Jan 1, 2010

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By G. V. Sullivan

This report summarizes the results of metallurgical investigations by the Federal Bureau of Mines of manganese oxide ore, averaging 23 to 25 percent manganese, stockpiled at the Butte-Philipsburg depot of General Services Administration (GSA). The oxide ores were stockpiled in two general classifications, straight oxide ore and mixed oxide-carbonate ore. Continuous-circuit flotation tests at the Albany (Oreg.) Metallurgy Research Center of the Bureau of Mines showed that each of these ore types could be concentrated by an oil-emulsion scheme to produce a concentrate that could be sintered to meet program specifications. About 88 percent of the manganese was recovered in the concentrate from the straight oxide sample, with the sintered concentrate containing 48 percent Mn. The sintered concentrate from the mixed oxide-carbonate sample contained 41 percent Mn with a recovery in the concentrate of 95 percent.

Jan 1, 1961

By R. C. Hickman

"INTRODUCTION Marl, consisting of a bed of coarse shell conglomerate from 1 to 5 feet thick, occurs on the Chesapeake Corporation tract and Philbates properties in New Kent County, Va.Nine holes were drilled on these properties in February 1946. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.LOCATIONThe Chesapeake Corp. deposit is reached from West Point, Va., by driving west on State Route 33 to the junction of State Route 634, approximately 5 miles. Proceed southeast along State Route 634 about three-quarters of a mile, at which point an old longing road turns north along a ridge and leads to the marl outcrops about one-half mile distant. The Philbates property lies three-quarters of a mile farther west along State Route 33 from the junction with State Route 634. The property lies north of State Route 33 and east of State Route 623 (fig. 1). The marl deposits are on the north end of the farm. The Chesapeake Corp. tract comprises 174 acres and the Philbato property 58 acres."

Aug 1, 1947

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By W. J. Kroll

The production of beryllium metal and its alloys is one of the most difficult tasks in metallurgy. In this report we shall examine the progress made in this work- in the last 15 years; taking into account the outstanding publications, including; those of the patent literature, and the information obtained during our 20 years? experience with this metal. The difficulties experienced' in producing elementary beryllium derive from the physical nature as well as from the chemical behavior of the metal and its compounds. Its oxygen affinity is about the same as that of calcium and a little higher than that of magnesium. Its chlorine affinity is much lower than that of magnesium, about equal that, of manganese, and little higher than that of aluminum. The sulfur and nitrogen affinity is probably almost the same as that of calcium for these elements, and beryllium carbide is probably more stable than aluminum carbide, A14C3. The intermetallic affinity of beryllium may be given in descending order, as follows: Nickel - copper - iron. It forms eutectics with -aluminum and silicon as well as with silver. It does not alloy with magnesium and only partly with calcium. Its oxide melts at 2,570° C., but CaO and BaO form readily fusible eutectics with BeO(65).3/ No igneous solvents are known for BeO, which behaves id this regard like Mgo. The beryllium silicate is a strong compound, the aluminete much less so; however, CaO easily displaces Be in the heated mixtures. The Anhydrous chloride hydrolyzes, and it cannot be made from aqueous liquors. It sublimes at 488° C, and melts at 405° C., The fluoride, which, is very Soluble in water, hydrolyzes also, but a kind of oxyfluoride of the approximate formula 2 BeO?5 BeF2 can be made from solutions by dessication. The fluoride melts at 800° C, and boils above 1,100° C. It forms very stable double fluorides with alkalifluorides, which have very low melting points and are fairly soluble in water. They are more stable than the analogous fluosilicates and the sodium fluoaluminate cryolite.

Jan 1, 1945

By F. G. Miller

[Petroleum tscknologists nnd progressive operatorr. constantly are striving to increase the percentage of oil thnt may be recorered from reservoir rocks through wells. The exhaustive studies that hve boen made of the function of natural gas in the production of oil, for example, havo aided operators greatly in increasing tho quantity of oil recovered from reservoirs. Natural gas dissolv.3d in and otheraiso asnociatod under pressuro with oil in rsservoir rocks, howovor, is not tho only source of energy available for rnovi~~ oil through sands to wells. In becomine Veservoi~enorgy conscious^^ encineera havo lonrned that in nnny petroleum resorroirs the edgewater flanking the oil accurrulation constitutos a potantinl source of enorgy cnpnblo, through pro1,sr control, of increasing oil-recovory officioncies materially. ?To longer is tho oncronchmont of mter into the oil- and gas-fillod uart of tho reservoir conridsred as evil to be combatted by dovious mothods but rnthar a nrtturrtl consequence, incident to the withdraval of oil nna gas from tho rolls, thnt mP.y be used nd~~mtngeoualy in lengthening the flowing life of wells ,md incre~sing the oconornic recovery nf oil and gns. Little is knom a3out tho nac'n-~nisrn by mhich wnter qor-rtos in driving nil through reservoir rocks, nnd thjro is n scnrcity of published informa- tion on rates of rnovzrnant of ~ntcr +,hat will result in naxilnm oil recoveries. Bureau of Xine s er.gir.ess nr r'reciate the ~aucity of scientific knowledge on the best methods of lying the natural rater drive to in- crease oil-recovery efficiencies arid ar9 initiating stildies that rill, they hope, contributo to tho procont small fund of information now available on the subject. This rh~.ort is s syr,o_nsis or brief c03pilation of published dAta and thought nccumulntod 30 far, groliminary to la-uorgtory ox~eriment+ tion NI& further resaarch on the principlgs und~rlying the nnturnl wnter drive RS it nffocts oil rocovory. The vrritors hopo th2t the omosition of available information prosentod in tho rey~ort rill stindate constructive thought and efforts loading torard moro comrlote extraction of oil and gas from resorvoirs.]

Jan 1, 1938

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By R. H. Grau, S. B. Robertson, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. Large-opening mine ventilation is unique for the following reasons: (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings to direct ventilation airflows are costly to construct and maintain. The research results suggest that by incorporating ventilation planning into the mine planning process, using propeller fans, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible, the ventilation of large-opening mines can be significantly improved. The ventilation improvements created by incorporating these various techniques into the ventilation plan will help reduce the exposure of mine workers to airborne contaminants in underground large-opening mines.

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By Paul M. Tyler

Masurium and rhenium are two elements known only to a few scientists and known to them for scarcely more than five years . The existence of two members of the manganese family was long suspected , and places were left for them in the orderly table of the periodic systemas developed by Mendeljeeff . The empty spaces left in this table some 60 years ago were for elements numbered 43 and 75 , respectively , and since it was evident these were related to manganese they were sought for in research laboratories under the names of ekamanganese and dvimanganese . This nomenclature is in harmony with that usually employed in describing hypothetical elements , and the prefixes are taken descriptively from ancient Sanskrit wherein the word " eka " means one and " dvi " ( also spelled dui or dwi ) means two . Ekamanganese or element 43 was once removed and dvimanganese or element 75 was twice removed from manganese . It was further possible to predict that these elusive elements would not only be related to manganese but would have a great deal in common with certain other elements . It was reasonable to suppose that element 43 , merely because it stood in numerical sequence between element 42 and element 44 , would likewise prove to be intermediate in many other respects . Since its next neighbors were molybdenum ( No. 42 ) on the one hand and ruthenium (No. 44) on the other , ekamanganese could be given in advance what would correspond among persons to a social and economic rating . Similarly , the properties of dvimanganese were likely to be in simple harmony with those of tungsten and with those of osmium , which latter , like ruthenium , is a member of the platinum group of metals . Another inference , although one which could not be stated with scientific certainty , is that these new elements because they have odd instead of even atomic numbers , would be even more sparingly distributed than their near neighbors , none of which is abundant in nature . This inference has been amply supported by available evidence . These elements eluded discovery until 1925 and never have been found except as minute traces in complex association with relatively rare minerals . In 1930 , for the first time , rhenium became available in quantities which give promise of commercial possibilities , but masurium still stands on the border of the unknown , like some distant star speck photographed and identified by vigilant astronomers but invisible without the aid of the powerful tools of science . The telltale flame of element 43 has been charted by its spectrum lines ; but beyond that , little more can be said except perhaps to repeat the forecasts made for ekamanganese before the Noddacks captured it and gave it a definite name . Certain rare - mineral dealers will furnish molybdenite samples from Norway which are said to contain masurium as well as rhenium , but except for a few highly technical statements as to its behavior in the spectrograph , nothing in the way of concrete information on masurium has come to the notice of the present writer . The literature of rhenium is a little less meager and a brief résumé of the data available in the files of the Bureau of Mines may be of interest not merely because of the novelty of the metal but because its unique properties and increasing availability afford a prospect of its finding employment in industry .

Jul 1, 1931