Search Documents

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

A preliminary program dated April 25, 1974 was prepared for Development Engineering, Inc. (D.E.I.) on research and development, laboratory; field and other engineering studies for the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included a discussion on the peculiarity of retorted shale materials to be investigated and a discussion of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I - Program Development II - Exploratory Laboratory tests on old U.S.B.M., retored shale III - Laboratory tests on Pilot Plant retorted shale IV - Laboratory tests on retorted shale from Semi-Works Plant, and field and test plots and ponds. V - Field compaction tests

Jan 1, 1975

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By E. J. Matson

The Table Mountain copper deposit is in an isolated portion of north-eastern Churchill County, Nev. Although copper-bearing outcrops have been known to exist in the area since 1909, no copper ore has been mined. Development of the property has been hampered by poor roads and rugged topography. Until 1941, the last 4 or 5 miles to the property had to be traveled either by foot or pack animal. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a project was started at the Table Mountain deposit. The Bureau began its field work on July 29, 1947, and completed it on October 18, 1948. Thirteen holes aggregating 2,711 linear feet, were drilled; samples were analyzed - 509 from cores and 143 from sludges. This report contains a brief history of the district and a description of the geology, deposits, and drilling done by the Bureau.

Jan 1, 1949

By Donald I. Kurth

The Bureau of Mines conducted experimental work on comminuting coal. The size distributions of coarse fragments and fine particles were obtained under different modes of energy application--drop, impact crushing, wedge impact, compression, and shear tests. Four levels of energy application were used in the impact crushing and wedge impact tests. Airborne dust and respirable air-borne dust distributions were obtained for the impact crushing and wedge impact tests. Analyses of nonairborne dust and coarse fragment-fine particle distributions were carried out on impact, wedge, compression, and shear tests. The experimental size data on nonairborne dust were fitted to normal, log-normal, power law, Weibull, log-Weibull, and exponential distribution functions. Both the nonairborne dust and the coarse fragment-fine particle size distributions are best described by Weibull distributions. For the impact crushing tests, mean product size was found to be inversely related to specific crushing energy. The particle counts in a given size range of airborne and nonairborne dust were found to increase with increased input energy and specific crushing energy. However, in another sense the particle distributions were independent of energy level; that is, the percent-ages in a given size range were approximately constant regardless of energy level. Respirable airborne dust was related to respirable-size nonairborne dust by a power law.

Jan 1, 1975

By D. Bienstock

In connection with air-pollution studies, the Bureau of Mines is cooperating with the U.S. Public Health Service in investigating the use of solids for removing sulfur dioxide in concentrations of less than 0.5 percent from combustion and waste gases. Removal of sulfur dioxide at flue-gas tempera¬tures would no longer result in the cooling of scrubbed gas, which is inherent to liquid scrubbing processes used exclusively in industry today. Results are reported of extensive investigation, using metallic oxides as absorbents, adsorbents, and oxidation catalysts at 130° and 330° C. (temperatures at which flue gas may be treated in powerplant practice). The most active absorbents tested were the oxides of manganese, cobalt, copper, and alkalized alumina; 23 to 33 grams of sulfur dioxidn were removed by 100 grams of absorbent at 130° C., while scrubbing more than 90 percent of the sulfur dioxide from a simulated flue gas, and 19 to 61 grams of sulfur dioxide were removed at 330° C. A more detailed study is reported on absorption and regeneration, using manganese oxides and alkalized alumina. Adsorption of sulfur dioxide on activated carbons and molecular sieves at elevated temperatures is considerably less efficient than removal by absorption--a maximum of 7 to 8 grams of sulfur dioxide could be removed with 100 grams of adsorbent at 130° C. A potash-promoted vanadium pentoxide is effective in converting sulfur dioxide to trioxide; complete conversion in a simulated flue gas containing 0.35 percent sulfur dioxide was obtained at 365° C. Pilot-plant and cost studies are being made by the Bureau to determine the economic feasibility of removing on an industrial scale the sulfur dioxide present in gases in low concentrations.

Jan 1, 1961

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By Douglas W. Fuerstenau

This report presents the results of an investigation of comminution in tumbling mills. Five different topics involved with ball mill and rod mill grinding kinetics were studied and the results analyzed in terms of phenomenological size reduction and transport models. Continuous rod mill grinding was found to be characterized by high Peclet numbers which permit simulation to be carried out by several methods. The dry batch ball mill grinding of mineral mixtures showed that the breakage rates of the components were composition-dependent but time-independent and were normalizable with specific energy. Locked-cycle tests on mineral mixtures showed that a grinding circuit may take a long time to attain steady-state, during which time the composition of the mill holdings, and hence the breakage rates of the components, continuously changed. This study revealed that under plant conditions, grinding circuits can be in transience perpetually. The transport of mineral mixtures through drums was found to exhibit complex size and/or density-dependent segregation. However, the grinding media in a ball mill can eliminate such segregation, thereby simplifying the modeling of the continuous grinding of complex feeds. Wet batch rod mill grinding on single minerals divulged that the normalizability of breakage kinetics is valid for slurries of constant pulp density at different hold-ups but cannot be extended to slurries varying in pulp density.

Jan 1, 1983

This Bureau of Mines report is devoted to descriptions of systems that provide in-mine wired telephone service. Although they may incorporate other features, each system described functions to allow one telephone to selectively access another telephone. Except for the paper on Conventional Telephone Equipment, the equipment described is newly developed and specifically designed to satisfy the requirements of underground mine communications.

Jan 1, 1977

By James P. May

Operating mine haulage trucks near the crest of stockpiles and waste dumps is a potentially hazardous practice often resulting in a localized slope failure and a dump point accident. The U.S. Bureau of Mines has developed a computer code (INSLOPE3) based on the kinematic method of limit analysis which determines an admissible truck weight (upper bound value) for varying distances from the slope edge. The program considers the material strength parameters, slope geometry, and inertial forces induced by vehicle braking. The program can be utilized to assist in the determination of safe operating distances for a haulage truck from a slope edge, the development of safe vehicle operating procedures, and the admissible weight for a static concentrated loading near the crest of an otherwise stable slope. This report provides information on the use of INSLOPE3, interpretation of the results for mining applications, and instructions for acquiring a copy of the software.

Jan 1, 1991

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By FREDERICK L. WARD

This paper , describing the operation of the Ward Sand and Gravel Co.'s plant at Oxford , Mich . , is one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of mining and preparing sand and gravel throughout the United States . These papers are designed to disseminate technical information regarding the methods used . The cost tabulations represent local operating expenditures only and not total production costs . It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole . On the other hand , operating costs are essential to the technical discussion and study of the methods employed . The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue . The plant described is a dredging operation with many unique features ; especially noteworthy are the mining of the sand and gravel with hydraulic jets operating on the principle of a water ejector , the unusual construction of the dredge and the self- unloading barges that tend it , the transportation of the sand and gravel to shore in barges instead of in pipe lines , the large storage capacity of the plant , and the fact that all material goes into storage before being shipped .

Jan 1, 1932

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993