Search Documents

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By Philip C. Tully

These modifications to the Redlich-Kwong equations for pure hydrogen and neon were developed after an unsuccessful attempt to generalize a modification technique previously developed for helium. New coefficients of the B terms were developed by minimizing the residuals. No changes were made in the coefficients of the A terms. For normal hydrogen, B was changed to [0.08063Tc PcT] for temperatures from 980 to 423° K and pressures up to 1,050 atm. The average deviation in Z was 0.36 percent with maximum deviations less than 1 percent for all but a few low-temperature points. For neon, B was changed to [PCT 0.1025T], for temperatures from 120° to 973° K and pressures up to 1,500 atm. The average deviation in Z was 0.34 percent with maximum deviations less than 1 percent for all but a few high-pressure and low-temperature points. Efforts to attain a lower temperature range to comparable accuracy with this type of modification were unsuccessful. In the range of applicability, these equations should be used with caution when calculating derived thermodynamic functions, such as the isobaric specific heat.

Jan 1, 1968

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale's organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale's organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By CLARENCE G. SMITH

Prior to the actual development of an oil property it is difficult to determine the quantity of oil under the property and the rate at which this oil can be brought to the surface-factors that determine the ultimate value of the property. Consequently, there has been much confusion in devising accounting systems that, during the entire life of a property, will show costs and profits from which the producer can determine whether his property is being worked at a profit or otherwise. The Bureau of Mines publishes this report in recognition of a distinct need for a simple treatise on accounting methods adapted to the peculiarities of the petroleum industry. Probably many companies operating oil wells are not fully acquainted with details important to the welfare of their business, because their account books fail to furnish them with exact and adequate data. With the accountant rests the responsibility of providing the management with reports setting forth the details of the business expressed in fitting terms as well as in dollars and cents. These reports are a means whereby efficiency may be maintained, waste prevented, oil obtained and sold, and money suitably reinvested. They also enable a concern to study the progress of its business in order to conserve to the utmost the possible benefits from an exhaustible deposit of mineral wealth. When managements realize the extent of the waste at their properties more attention will be given to the character of the accountancy records. Herein are presented descriptions and discussions of balance sheets, profit-and-loss statements, and bookkeeping methods peculiarly adapted to the oil business. As far as possible, technical phrases have been omitted in order that those not familiar with accounting terms may be able to follow the subject matter. The systems of keeping books outlined in Chapter X have all been found practical. For brevity as well as clearness the major part of the work refers to the company operating only one property.

Jan 1, 1917

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By R. H. Hiltz

One of the major hazards in underground coal mining is fire. The inherent hazard of fire is exaggerated by the nature of coal mining restricted areas, the highly combustible nature of coal itself, and a potential for explosive concentrations or dust and gas in the air it becomes imperative therefore to make every effort to eliminate the causes of fires, while providing the most effective means possible to control and extinguish those fires which may occur it has been demonstrated by prior work that the problem of control increases in proportion to the time necessary to institute control procedures. There are several areas of underground coal mining with obvious fire potential. Some of these, like belt heads, have reliantly undergone improvements in standby fire control devices Others, although having fire suppression systems available to them, have not received as complete a systematic study of their problems. Face machinery, particularly those without a water supply, falls in this latter category.

Jan 1, 1973

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By Sidney Katell

This report, covering the period January 1967 through December 1967, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the ninth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week.

Jan 1, 1968

By Fremont F. Clarke

"INTRODUCTION Clay beds of southwestern North Dakota were investigated to determine (1) the average alumina content of the clays in four principal areas of occurrence, (2.) which, if any, would be the most feasible method of extracting alumina from the clays, and (3) whether the clays had any other commercial uses.During the investigation exposed sedimentary beds were examined for clay and the thickness and areal extent of outcropping clay beds in the more promising areas were measured. Four-principal areas of bentonitic clays, comprising 6,967 acres in Stark, Slope; and Billings Counties, N. Dak., were mapped and sampled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chiefs analyzes samples and makes beneficiation tests.Acknowledgment is duo John P. Gries, professor of geology, South Dakota School of Mines and Technology, for his studies of and advice on geological phases of the work. His data were drawn on freely in preparing this report; also E. D. Gardner, regional engineer, Rolla, Mo., and E. Y. Dougherty, district engineer, Rapid City, S. Dak., for assistance and advice in supervising the program."

Mar 1, 1948

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By C. M. Harrer

This paper describes the location and general features of iron occurrences in Colorado. Most of the deposits were examined; many are in forested and mountainous areas at altitudes of 5,000 to 13,700 feet. Iron is known to occur in 30 counties of western Colorado. Transporting the ore to market is a handicapping economic factor involving long truck and railroad hauls; the nearest purchaser of smelting ores is the Colorado Fuel and Iron Corp., at Pueblo, Colo. When the ore can be sold locally for special purposes and at higher prices than can be obtained at iron smelters, small-scale operations can supply that market.

Jan 1, 1959